Seeley magiq Manuel utilisateur
INSTALLATION MANUAL
MagIQ Touch Controller
(English)
MAGIQ TOUCH CONTROLLER INSTALLATION MANUAL |1
CABLE LENGTHS 1
MOUNTING THE CONTROLLER 2
CONNECTING THE CONTROLLER 8
SINGLE COMPONENT INSTALLATION (NO ZONES) 8
MULTIPLE COMPONENT INSTALLATIONS 10
OPERATION SCREENS 11
SETTINGS MENU 13
GENERAL MENU 15
COOLER & HEATER MENUS 15
SERVICE MENU 16
CONTROLLER OR SYSTEM RESET 19
MANAGING COMPONENTS 20
ADDING COMPONENTS 20
REPLACING COMPONENTS 21
REMOVING COMPONENTS 22
MANAGING THE CONTROLLER 24
CONNECTING A NEW CONTROLLER
TO AN EXISTING SYSTEM 24
CONNECTING A PRE-USED CONTROLLER 25
FAULT ROUTINE 26
POWER OUTAGES 28
TROUBLE SHOOTING 29
TABLE OF CONTENTS
• Cables used for the MagIQ Touch Controller
are26AWG,7/016,6coreat.
• 20m/66"cable is supplied with each Seeley cooler or heater
• 40m/131"cable is also available
• Suppliedcablesshouldnotbealtered.
ALWAYS route cables at least 300mm / 12"away from regular
powercablesandhighpowermachines.Crossoverpowercables
atrightangles.
Important!
Where maximum cable lengths are exceeded, or cables are not
routed in accordance with our recommendations Seeley technical
supportisnotavailableandtheproductwarrantymaybevoided.
Note!
The term “component” (Seeley International cooler or heater)
will be used in this document to describe any separate device,
such as a cooler, heater or sensor, which is to be connected
totheMagIQTouchController.
CABLE LENGTHS
40m / 131"
MAX
ILL1583-A
Seeley International
cooler or heater
2 |MAGIQ TOUCH CONTROLLER INSTALLATION MANUAL |3
TheControllershouldbeplacedapproximately1.5metresabove
theoor,inthemostusedroomofthehome.
Placement is critical for correct functioning of the temperature
sensingthermostatinsidethecontroller.
The following points must be taken into consideration:
• Avoiddirectsunlightexposure.
• Avoidmountingonexternalwalls.
• Avoid mounting the wall control near heat sources such as
stovesandtelevisions.
• Donotlocateinthedirectairowoftheductoutlets.
• Do not locate in strong drafts or in dead spots such as
cupboards/drawers.
• Alwayssealthecableentryhole.Hotorcoldaircomingthrough
thewallmayinterferewiththetemperaturemeasurement.
CAUTION!
Always make sure there are no electrical cables, gas or
water pipes, or the like, behind where you intend to drill.
MOUNTING THE CONTROLLER
RemovethemountingbracketfromtherearoftheController.
MOUNTING THE CONTROLLER cont
STEP 1
STEP 2
STEP 3
ILL1584-A
ILL1585-A
ILL1586-A
4 |MAGIQ TOUCH CONTROLLER INSTALLATION MANUAL |5
Using the bracket as a template, mark the centre points
forthescrewandcableaccessholes.
MOUNTING THE CONTROLLER cont
Important! The cable hole should be positioned centrally
withintherectangularwindowinthemountingbracket. Alternatively, a standard stud mounting bracket
(usedforwallplates)canbeusedwithplasterboardwalls.
MOUNTING THE CONTROLLER cont
Insertwallplugsintoholes.Alignandscrewthebracketinto
positionusingthesuppliedscrews.
ILL1587-A
ILL1597-A
ILL1589-A
ILL1591-A
ILL1590-A
ILL1588-A
Drill a 16mm hole for cable access, and two smaller
holesforthewallplugsprovided(5mmholesfor
plasterboardwallsor6mmholesforbrickwalls).
6 |MAGIQ TOUCH CONTROLLER INSTALLATION MANUAL |7
Draw the cable through the wall cavity to the hole made at the wall
bracket.Connectthecabletothewallcontrolandmountthewall
controlontoitsbracket.
MOUNTING THE CONTROLLER cont
Slideandalignthewallcontrolovertheprotrudingbrackettabs.
Pull the wall control down so the bracket tabs engage and locate
withthekeywayslotsontherear.
MOUNTING THE CONTROLLER cont
Important! Take care not to damage the cable or plug during this
process.
Important! Drafts within the wall cavity can impact the temperature
readingofthewallcontrol.Werecommendthatthecableaccess
hole be sealed, but in such a way that the cable can still retreat into
thewallcavity.
STEP 1
STEP 2
ILL1592-A
ILL1593-A
ILL1594-A
8 |MAGIQ TOUCH CONTROLLER INSTALLATION MANUAL |9
CONNECTING THE CONTROLLER
ToactivatetheControllerscreen,pressthebuttontotheright.
SINGLE COMPONENT INSTALLATION (NO ZONES)
Ensuring the Controller is properly connected
poweruptheheater/cooler.
ILL1521-A
CONNECTING THE CONTROLLER cont
Select “ALL NEW SYSTEM” option and start the
“SystemInstallationWizard”.
Accept“01”asthenumberofcoolers/heaterstobeinstalled.
ILL1610-A
ILL1611-A
ILL1595-A
10 |MAGIQ TOUCH CONTROLLER INSTALLATION MANUAL |11
Thecontrollerwillscantondthecomponent(cooler/heater).
Whenithasbeenidentied,continuetotheoperatingscreen.
MULTIPLE COMPONENT INSTALLATIONS
The Controller uses a ‘System Installation Wizard’ to assist
withtheinstallationprocess.
Therstpartofthewizardrequirestheinstallertospecifythe
type and number of components that will be installed in the
system.ThisstepisimportantbecausetheControllerneeds
components to be connected and powered up one at a time
and in the correct order.
Note!Itisimportantthatcomponents(e.g.heaters,coolers,
sensorsetc.)areconnectedONE AT A TIME as prompted by the
Controller.Ifmorethanonecomponentofthesamedevicetype
is connected at the same time there is a risk of communication
corruption and the system will not function correctly!
The system installation is complete once all components have
beendetected.
CONNECTING THE CONTROLLER cont
Skipnowtothe‘OPERATIONSCREENS’chapter.
ILL1612-A
Selectprimarymode(COOL/HEAT/FANONLY):
OPERATION SCREENS
Turn system on & off:
Adjust temperature:
ILL1613-A
ILL1614-A
ILL1615-A
12 |MAGIQ TOUCH CONTROLLER INSTALLATION MANUAL |13
Access advanced display:
OPERATION SCREENS cont
Choose between MANUAL or PROGRAM modes
or access SETTINGS menu:
For detailed information on the operation screens
refer to the MagIQ Touch Controller Owner’s Manual.
ILL1616-A
ILL1617-A
SETTINGS MENU
The SETTINGS menu contains a GENERAL menu relating to the
Controllerandthesystemasawhole,COOLERandHEATER
menus depending on what has been installed, and a SERVICE
menucontainingcomponentdetailsandfaultinformation.
Note! The controller will only display the menus and menu items
thatarerelevanttotheinstalledsystem.
Navigate through the menus by tapping the heading tabs
atthetopofthescreen.
Allthemenuitemsarelistedonthelefthandsideofthescreen.
ILL1618-A
ILL1619-A
ILL1620-A
14 |MAGIQ TOUCH CONTROLLER INSTALLATION MANUAL |15
SETTINGS MENU cont
Thecurrentstatusislistedontheright,closetothearrowbuttons.
If you want to change a setting or access a menu item,
pressthearrowbutton.
Some menu items are locked with a pin code to
discouragecustomeraccess.Thepincodeis7378.
ILL1599-A
ILL1621-A
ILL1622-A
GENERAL MENU
The GENERAL menu includes settings or information related
totheMagIQTouchController,orthesystemasawhole.
• Time and Date
• Language
• Child Access Lock (set a pin to restrict access)
• Zone Renaming (customise zone names)
• SystemConguration
• System or Controller Reset
COOLER & HEATER MENUS
TheCOOLERandHEATERmenusincludesettingsorinformation
relatedtothespecicSeeleyInternationalcoolingorheating
productsinstalledwithinthesystem.
Moreinformationaboutthespecicsettingsoftheseproducts
is provided in the separate product installation guide
ILL1623-A
16 |MAGIQ TOUCH CONTROLLER INSTALLATION MANUAL |17
SERVICE MENU
The SERVICE menu contains information and functions
forcompetentservicepersonnel.
Accessislockedwithaservicepincode.Thepincodeis7378.
Once the pin code is entered you will have access to component
specicinformationsuchasmodelnumber,serialnumber,etc.
ILL1624-A
ILL1625-A
ILL1626-A
SERVICE MENU cont
Also included in this menu is access to a ‘Service Operating
Screen’foreachcomponentinstalledinthesystem.Thisscreen
canbeusedasatroubleshootingtool.
On this screen the status of the component
isdisplayedandcanbemodied.
ILL1627-A
ILL1628-A
Autres manuels pour magiq
1
Table des matières
Autres manuels Seeley Routeur réseau
Manuels Routeur réseau populaires d'autres marques
NETGEAR
NETGEAR FS526T - Switch Manuel utilisateur
Korenix
Korenix JetNet 5710G Series Manuel utilisateur
Automated Logic
Automated Logic ZN551 Manuel du propriétaire
Cisco
Cisco ASR 1000 Series Manuel de l'opérateur
EnGenius
EnGenius ESR-9710 Manuel utilisateur
Cisco
Cisco 805 Series Instructions d'utilisation et de sécurité