Securitytronix ST-PTZMINI-540W Manuel utilisateur

v2.0 3/21/11

INSTALLATION MANUAL

ST-PTZMINI-540W

Medium Speed Intelligent

Dome PTZ Color Camera

v2.0 3/21/11

PACKAGE CONTENTS

This package contains:

One ST-PTZMINI-540W medium speed dome color camera

One installation manual

Note: The ST-PTZMINI-540W requires a minimum 12VDC 1.2A power supply such as the

ST-PS12VDC2A.

PRODUCT DESCRIPTION

The ST-PTZMINI-540W is a professional grade indoor dome color camera with pan, tilt and zoom

(PTZ) capability of 540TVL of resolution. The camera’s full digital design allows the saving of all

settings in non-volatile memory. Its 128 preset positions allows up to 8 preset positions for auto

tracking functions. The ST-PTZMINI-540W’s mechanical design permits continuous horizontal

360°rotation, 0 to 92°vertical rotation and 180°auto turning. The camera features include auto

focus, auto iris, auto bright controls, color and black/white auto change, AWB, BLC and AES. The

ST-PTZMINI-540W uses the PELCO-D protocol.

SPECIFICATIONS

ST-PTZMINI-540W

Specifications (Typical)

1. Image Sensor

1/3” SONY Super HAD CCD with DSP

2. Resolution

540TVL Color; 600TVL B&W

3. Lens

Auto Iris; 5mm –15mm; 3X optical zoom w/auto-focus

4. Illumination

0.01 Lux

5. Video Output

1.0±0.2VP-P, 75Ωcompound video signal

6. Signal to Noise Ratio

≥50dB

7. Manual Speed

Horizontal (0.5°~50°/s) / Vertical (0.5°~50°/s)

8. Preset Speed

50°/s

9. Rotation

Horizontal 360°continuous / Vertical 0~92°with auto overturn

10. Focus Speed Auto Control

Control speed auto-adjusting according to the focal length

11. Preset Positions

128

12. Auto Overturning

Vertical 90°, auto turning into 180°

13. Auto Scanning

2 pieces, 1 auto scanning route and speed can be set

14. Synchronization

Internal/External optional

15. Communication Baud Rate

1200/2400/4800/9600 bps

16. Address Range

1~255

17. Operating Humidity

0~95%

18. Operating Temperature

14°- 122°F

19. Power Supply

DC12V 1.2A

20. Dimensions

5”x 5”

21. Weight

2.2 lbs

v2.0 3/21/11

INSTALLATION AND OPERATION

CAUTION: To reduce the risk of electrical shock do not remove the cover or back of this

unit. No user serviceable parts are inside.

CAUTION: To prevent electric shocks and risk of fire hazards, do not use other than

specified power source.

1. UNPACKING and HANDLING

Each unit is shipped assembled and factory tested.

Ensure that all accessories are removed from the container before discarding packing material

2. MECHANICAL INSPECTION

Inspect the front and rear of the equipment for shipping damage. Make sure the equipment is

clean, and no connectors are broken, damaged, or loose. If equipment appears to be

damaged or defective please contact your distributor or SecurityTronix at 1-610-429-1511 for

assistance.

3. SPECIAL ATTENTION

a. The installer must comply with electrical safety standards. There must be sufficient

space between the camera’s power supply and video line and any high voltage

equipment and/or cables.

b. To help ensure the camera’s life and proper operation do not point the camera

towards the sun or strong light.

c. Do not install the camera in an environment where the temperature is above 122°F.

d. Do not install the camera near a magnetic field or a high-power motor.

e. Do not mount the camera near a radiator or heater.

f. Only use a dry cloth to clean the camera. If there is dirt that is difficult to remove wipe

gently with a mild detergent. Never use strong or abrasive detergents.

g. A minimum 12VDC 1.2A power supply must be used. AC power cannot be applied.

Using an AC or other incorrect power supply will damage the camera.

h. Only qualified installers are allowed to install, test and disassemble the camera.

i. The camera is a low voltage product. If installed outdoors proper safety and lightening

grounding are required.

This symbol is intended to alert the user to the presence of important operating and

maintenance (servicing) instructions.

This symbol is intended to alert the user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a

risk of electrical shock.

v2.0 3/21/11

4. WIRING CONNECTIONS

a. Connect the power supply’s DC plug to the camera’s power outlet.

b. Connect the camera to the monitor with a 75Ωcoaxial video cable.

c. Connect unshielded twisted pair (UTP) control cable between the camera’s RS485

port and the PTZ controller. Be sure wire polarities are the same at each connection.

The camera’s violet wire (A) is + positive and the white wire (B) is –negative.

d. Connect power supply’s AC plug to a suitable AC power outlet.

e. Adjust the lens direction according to the required surveillance area and environment.

5. FUNCTIONS and OPERATION

Configuring the ST-PTZMINI-540W

The ST-PTZMINI-540W’s control board has an 10-DIP switch used to set a number of

parameters including address, communications protocols and control protocols. Any

command used should conform to the target camera and that camera’s response should occur

only when it has been addressed.

Of the 10 DIP switches:

Switches 1, 2, 3, 4, 5, 6, 7 and 8 are for setting the camera address.

Switches 9 and 10 are for setting the communications baud rate.

Set Camera Address

The tables below indicate DIP switch settings for creating the camera’s address. “1”

indicates the switch is set “ON” while “0” indicates the switch is set “OFF”.

v2.0 3/21/11

Address

Address Switch

Address

Address Switch

Code

1 2 3 4 5 6 7 8

Code

1 2 3 4 5 6 7 8

1 0 0 0 0 0 0 0

1 0 0 0 0 1 0 0

0 1 0 0 0 0 0 0

0 1 0 0 0 1 0 0

1 1 0 0 0 0 0 0

1 1 0 0 0 1 0 0

0 0 1 0 0 0 0 0

0 0 1 0 0 1 0 0

1 0 1 0 0 0 0 0

1 0 1 0 0 1 0 0

0 1 1 0 0 0 0 0

0 1 1 0 0 1 0 0

1 1 1 0 0 0 0 0

1 1 1 0 0 1 0 0

0 0 0 1 0 0 0 0

0 0 0 1 0 1 0 0

1 0 0 1 0 0 0 0

1 0 0 1 0 1 0 0

0 1 0 1 0 0 0 0

0 1 0 1 0 1 0 0

1 1 0 1 0 0 0 0

1 1 0 1 0 1 0 0

0 0 1 1 0 0 0 0

0 0 1 1 0 1 0 0

1 0 1 1 0 0 0 0

1 0 1 1 0 1 0 0

0 1 1 1 0 0 0 0

0 1 1 1 0 1 0 0

1 1 1 1 0 0 0 0

1 1 1 1 0 1 0 0

0 0 0 0 1 0 0 0

0 0 0 0 1 1 0 0

1 0 0 0 1 0 0 0

1 0 0 0 1 1 0 0

0 1 0 0 1 0 0 0

0 1 0 0 1 1 0 0

1 1 0 0 1 0 0 0

1 1 0 0 1 1 0 0

0 0 1 0 1 0 0 0

0 0 1 0 1 1 0 0

1 0 1 0 1 0 0 0

1 0 1 0 1 1 0 0

0 1 1 0 1 0 0 0

0 1 1 0 1 1 0 0

1 1 1 0 1 0 0 0

1 1 1 0 1 1 0 0

0 0 0 1 1 0 0 0

0 0 0 1 1 1 0 0

1 0 0 1 1 0 0 0

1 0 0 1 1 1 0 0

0 1 0 1 1 0 0 0

0 1 0 1 1 1 0 0

1 1 0 1 1 0 0 0

1 1 0 1 1 1 0 0

0 0 1 1 1 0 0 0

0 0 1 1 1 1 0 0

1 0 1 1 1 0 0 0

1 0 1 1 1 1 0 0

0 1 1 1 1 0 0 0

0 1 1 1 1 1 0 0

1 1 1 1 1 0 0 0





0 0 0 0 0 1 0 0

255

1 1 1 1 1 1 1 1

Set Communications Baud Rate

“1”indicates the switch is set “ON” while “0” indicates the switch is set “OFF”.

Baud Rate

Switch #

9 10

1200bps

1 1

2400bps

0 1

4800bps

1 0

9600bps

0 0

v2.0 3/21/11

FUNCTIONS

The user can control camera and lens movement through the use of a PTZ Controller. Further,

the user can track the target or shift the view while the camera’s focal length can be adjusted

to the required view angle and target image sizing. Note although manual adjustment of focal

length is possible while the dome moves at a high speed, the ST-PTZMINI-540W allows for

automatic horizontal and vertical dome speed adjustment consistent with lens focal length and

zoom settings so no information is lost during camera movement.

Zoom Control

The user can adjust the image farther or nearer to acquire a panoramic view by use a PTZ

Controller’s Zoom -/ Zoom + controls. The ST-PTZMINI-540W supports both digital and

optical variable focus. There are certain conditions whereby the camera may not be able to

auto focus:

The target is not in the center of the image.

The target is in bright light (e.g., neon light, spot light).

The target or object is moving too fast.

The target is a large, square monotonous object such as a wall.

The target is too dark or vague.

The target is too small.

Surveillance Functions

A preset position is the storing of a camera location parameter such as horizontal angle,

inclination, or lens focus in memory and transferring them to the camera when needed.

Recalling and transferring preset positions is done through the PTZ Controller. The

ST-PTZMINI-540W supports 128 preset positions.

Set Preset Positions

The ST-PTZMINI-540W supports up to 128 preset positions. Setting the preset positions using

a PTZ Controller is done as follows by way of example:

Move the joystick so the camera is on the location or image for the first preset point.

Push Preset button on the PTZ Controller and press number 1 and ENTER for Preset

Position #1.

Move the joystick so the camera is on the location or image for the second preset

point. Push Preset button on the PTZ Controller and press number 2 and ENTER for

Preset Position #2.

Continue the above steps for each preset position to be entered.

To move the camera to an existing preset point press CALL and the appropriate

number. E.g., to point the camera to Preset Position #2 press CALL and 2.

Set Scanning

Auto Scanning – The camera performs a level scan back and forth among the left and right

limits at a set speed –is incorporated in the ST-PTZMINI-540W. Left and right limits and scan

speed are set using the PTZ Controller. Auto scan can be done using CALL #125 or pressing

the auto-scan button on the PTZ Controller. The camera will auto scan 360°back and forth.

The auto scan speed is fixed.

Linear Scanning – The camera may also be set to scan back and forth between two fixed

positions established as preset positions. The scanning speed can be set from 1°to 50°per

second. By way of example, and using 50°per second as the scan speed, via the PTZ

v2.0 3/21/11

Controller:

Preset #126 for linear scanning.

Preset #1 to 50 (1 being slow, 50 being fast) as the speed index for total scan speed

time. Note each value refers to °/second (e.g., 1 = speed of 1°/second)

Move the controller’s joystick to the beginning location and adjust the image to be

viewed.

Preset #127 as the preset point for the beginning location.

Move the joystick to the ending location and adjust the image to be viewed.

Preset #128 as the preset point for the ending location.

Call 128 to activate the linear scan.

Tour

Automatic Tour is incorporated in the ST-PTZMINI-540W allowing preset points to be inserted

into a tour list. These preset points with timing pauses can be programmed as a tour route. In

so doing, the ST-PTZMINI-540W can automatically follow a predefined path or route. Up to 8

preset points and timing pauses can be stored in the camera. Two tour routes (#101 and

#102) can be created using 8 preset points each. The camera pauses 6 seconds at each

point. By way of example for Tour Route #101 using 3 preset points:

Preset 101.

For preset point 1 –move joy stick to the first location and Preset point 1.

For preset point 2 –move joy stick to the second location and Preset point 2.

For preset point 3 –move joy stick to the third location and Preset point 3.

Call 101 to activate Tour Route #101.

6. TROUBLESHOOTING

a. No picture after applying power –(i) check all plugs and cables are securely

connected to the proper connectors; (ii) ensure your power supply is providing the

correct voltage and current.

b. The picture has ripples –(i) check to see if the power supply is experiencing AC ripple,

if so a filter may be required; (ii) determine if the monitor is faulty; (iii) determine if

other peripheral equipment is causing ripple and if so make the necessary

adjustments.

c. The picture background continuously changes color –a fluorescent lamp’s magnetic

field may cause color roll, therefore, reduce the number of fluorescent lamps or

increase the distance between the camera and the lamps.

d. The picture appears smeared –(i) the power supply voltage level may be unstable,

therefore, try another power supply; (ii) ensure the cables are correctly connected

and/or the cables are of the correct impedance.

e. Other interference may require a SecurityTronix ground loop isolation filter.

f. Power is on, but the controller does not work –(i) check to make sure the DIP

switches for address and communications baud rate are properly set, (ii) check to

ensure the RS485 connections at the camera and the PTZ Controller have the same

polarity, (iii) check the integrity and continuity of the unshielded twisted pair (UTP)

control cable.

g. Additional troubleshooting assistance can be found on-line at www.securitytronix.com

in addition to support from SecurityTronix sales engineers at 1-610-429-1511.

v2.0 3/21/11

APPENDIX: PELCO-D PROTOCOL

The ST-PTZMINI-540W uses the PELCO-D protocol. Below is a description of the protocol for

those installers or system integrators in need of the protocol’s details.

Data Form: 1 beginning position, 8 pieces for data, 1 ending position, invalid checking point.

Baud Rate: 2400, 4800, 9600, 19200bps.

Command Form:

Byte 1

Byte 2

Byte 3

Byte 4

Byte 5

Byte 6

Byte 7

Synchronized

Byte

Address

Code

Command

Code 1

Command

Code 2

Data Code 1

Data Code 2

Confirmation

Code

All data in the protocol as HEX

Synchronization Byte is 0FFH

Address Code is the logical address number of cameras.

Address Range is 01H –0FFH

Form of Command Code:

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Command

Code 1

Auto

Scan

Iris

Open

Focus

Near

Command

Code 2

Focus

Far

Zoom

Wide

Zoom

Tele

Down

Left

Right

Command Code 1: Bit 7, Bit 6, Bit 5, Bit 3 is 0 without exception. Bit 4 is auto scanning

control points (1/0 ON/OFF). Bit 2 Iris Smaller (1 valid). Bit 1 Iris Larger (1 valid). Bit 0

Focus Nearer (1 valid).

Command Code 2: Bit 7 Focus Farther (1 valid). Bit 6 & Bit 5 for zoom control: Bit 6 far

away from the object (1 valid), Bit 5 near the object (1 valid). Bit 4, Bit 3, Bit 2, Bit 1

separately control the movement down, up, left, right (1 valid). Bit 0 is 0 without exception.

Data Code 1: Controls the horizontal direction of speed 00 –3FH.

Data Code 2: Controls the vertical direction of speed 00 –3FH.

Confirmation Code Index: [Byte 2 + Byte 3 + Byte 4 + Byte 5 + Byte 6 / 100H].

Confirmation Code = MOD [Byte 2 + Byte 3 + Byte 4 + Byte 5 + Byte 6 / 100H].

Setting and Transferring Preset Command

Set the Command for Preset Positions

Byte 1

Byte 2

Byte 3

Byte 4

Byte 5

Byte 6

Byte 7

Synchronized

Byte

Address

Code

00H

03H

00H

Present

Point #

Confirmation

Code

Transfer the Command of Preset Positions

Byte 1

Byte 2

Byte 3

Byte 4

Byte 5

Byte 6

Byte 7

Synchronized

Byte

Address

Code

00H

07H

00H

Present

Point #

Confirmation

Code

Preset Point # Range is 00 –FFH

v2.0 3/21/11

Turn On and Off the Command of Auxiliary Switches

Turn On the Command of Auxiliary Switches

Byte 1

Byte 2

Byte 3

Byte 4

Byte 5

Byte 6

Byte 7

Synchronized

Byte

Address

Code

00H

09H

00H

Auxiliary

Switch #

Confirmation

Code

Turn Off the Command of Auxiliary Switches

Byte 1

Byte 2

Byte 3

Byte 4

Byte 5

Byte 6

Byte 7

Synchronized

Byte

Address

Code

00H

0BH

00H

Auxiliary

Switch #

Confirmation

Code

Auxiliary Switch # Range is 01 –08.

Table des matières

Autres manuels Securitytronix Caméra de sécurité

Securitytronix

Securitytronix ST-BT6003.6-W2 Manuel utilisateur

Securitytronix

Securitytronix ST-BT600SIR –B Manuel utilisateur

Securitytronix

Securitytronix ST-D600IR2812-HB Manuel utilisateur

Securitytronix

Securitytronix HD-Coaxinator ST-HD-BT2812-1MP Manuel utilisateur

Securitytronix

Securitytronix ST-D600VP3.6-B-W Manuel utilisateur

Securitytronix

Securitytronix ST-BTLI540IR20 Manuel utilisateur

Securitytronix

Securitytronix ST-HD-BT2812M-2MP Manuel utilisateur

Securitytronix

Securitytronix ST-D700IR2812-B/W Manuel utilisateur

Securitytronix

Securitytronix ST-BTWD600IR40-B Manuel utilisateur

Securitytronix

Securitytronix ST-IP-BTVF-2 Manuel utilisateur

Securitytronix

Securitytronix ST-D600DNVP2812 Manuel utilisateur

Securitytronix

Securitytronix HD-COAXINATORTVI ST-HDC2FTD Manuel utilisateur

Securitytronix

Securitytronix ST-WD600PTZMINI Manuel utilisateur

Securitytronix

Securitytronix HD-COAXINATORTVI ST-HDC2VFTD-MZ Manuel utilisateur

Securitytronix

Securitytronix ST-CVTMD420-WPIR-W Manuel utilisateur

Securitytronix

Securitytronix ST-IP2FWD Manuel utilisateur

Securitytronix

Securitytronix ST-IP4VFD-MZL Manuel utilisateur

Securitytronix

Securitytronix ST-IP6FE Manuel utilisateur

Securitytronix

Securitytronix ST-DWDVF2812-720B/W Manuel utilisateur

Securitytronix

Securitytronix ST-HD-D2812M-2MP Manuel utilisateur

Securitytronix

Securitytronix ST-PTZ480-22 Manuel utilisateur

Securitytronix

Securitytronix ST-D7002812-B Manuel utilisateur

Securitytronix

Securitytronix ST-BT1000IR2812-G Manuel utilisateur

Securitytronix

Securitytronix ST-DWD650IRVP2812-B/W Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur