SECURECOM V-4408D Manuel utilisateur

DESCRIPTION

V-4408D EIGHT-CHANNEL

NETWORK VIDEO RECORDER (NVR)

Installation Guide

Figure 1: V-4408D Network Video

Recorder (NVR)

1INSTALL THE V-4408D

1. Attach the included power cable to the back of the NVR.

See Figure 2.

2. Attach the other end of the power cable into a wall outlet.

3. Power on the NVR with the switch on the back.

2Connect cameras and any peripheral devices to the ports in the

back of the NVR. See Figure 2 for port locations.

LAN

Connect the NVR directly to the customer’s network using the

LAN port.

USB

Connect USB devices like a mouse, keyboard, ﬂash drive, or an

external hard drive to the NVR using the two built-in USB ports.

HDMI

Connect one end of the HDMI cable to the NVR and the other

end to a TV or monitor to monitor video.

Hikvision and 4000 Series

Can only be automatically learned in if they are plugged into the

camera ports on the back of the NVR.

5000 Series

Cannot be plugged in to the ports on the back of the NVR. Also

requires that a DHCP reservation is set up on the router. For more

information, refer to the documentation for your router model.

1 2 3 4

5 6 7 8

AUDIO IN

AUDIO OUT VGA HDMI

LAN

Power

Switch

Figure 2: V-4408D Ports

CONNECT THE DEVICES DIRECTLY

8 Camera Ports

HDMI

LAN

USB

Power

On/O

Switch

The SecureCom™ Video V-4408D

Eight-Channel NVR connected to

residential or commercial systems

gives users a more powerful

security tool to monitor cameras

connected to their systems.

The V-4408D provides Power over

Ethernet (PoE) capability, allowing

you to supply power to a network

camera using the same cable that

transmits the data.

The V-4408D provides 2 TB of

storage for around the clock, local

recording. The V-4408D supports all

ONVIF 2.4-compatible cameras and

is viewable on the Virtual Keypad™

App or VirtualKeypad.com and can

be monitored from any monitor with

and HDMI cable or with Apple TV

(Virtual Keypad™ App required).

Compatibility

• 4000 or 5000 Series

SecureCom Video Cameras

• ONVIF-Compliant Cameras

• Hikvision Cameras

What is Included?

• SecureCom Video V-4408D

Eight-Channel NVR

• Power cable

• Three-button USB mouse

• 6 ft Network cable

• Hard drive cable

• Hardware pack

2 V-4408D INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS

3ACTIVATE THE V-4408D

Locally (Optional)

1. Click Yes on the Warning Screen to activate the NVR locally.

2. Type securecom into the Old Password ﬁeld.

3. Type in a new password of your choosing and click OK. Your password should be between 8-16

characters and should consist of two of the following options; numbers, letters, special characters.

4. You will be notiﬁed that the password has been modiﬁed. The GUID (Globally Unique Identiﬁer) ﬁle can

be exported at a later time in case you forget your password.

5. Select OK.

6. After successfully activating the NVR, log in to dealer.securecomwireless.com and complete steps 2

through 8 below.

Remotely with Dealer Admin

1. Log in to dealer.securecomwireless.com.

2. Select the customer’s system account number to add the V-4408D.

3. Click + NVR/Converter.

4. Enter the Device Serial Number found on the NVR label.

5. Click Next. To add cameras.

6. When the NVR has successfully connected, the Device Serial Number is assigned as the serial number

and the name. The name can be changed here.

7. Create an NVR Username and Password to create a local operator account for viewing prerecorded

video locally using an HDMI-connected device.

Note: You do not need to add the NVR Username and Password for SecureCom to connect to the

NVR.

8. Select the Time Zone and leave Observe Daylight Savings Time as default if observed by the area and

enable the local user option.

9. Click Save.

4CONNECT A CAMERA TO THE NVR

To connect over PoE/Network, connect one end of the network cable to one of the eight provided ports on

the back of the NVR. Up to eight cameras can be connected using PoE. The NVR will automatically add any

4000 Series SecureCom camera that is connected to one of the eight PoE ports. When using PoE, no power

cable is needed.

Note: When managing 5000 Series cameras with both the V-4408D NVR and Dealer Admin, cameras

must be connected to the NVR through a switch.

Conﬁguration Details

Refer to the following information for the conﬁguration details of speciﬁc camera models.

V-4060DB Admin Veriﬁcation

For the V-4060DB Doorbell, the password is a combination of the word “admin” followed by the veriﬁcation

code that is on the doorbell’s label found under the cover below the serial number. As an example, if the

veriﬁcation code is ILGWQM then the password would be adminILGWQM.

5000 Series Default Passwords

For V-5012B or V-5052D cameras with lower than D3.2.1_20200818_DMP ﬁrmware and V-5014B or V-5054D

cameras with lower than D4.2.1_20200818_DMP ﬁrmware, the default password is scw12345user.

For V-5012B and V-5052D cameras with ﬁrmware Version D3.2.1_20200818_DMP and higher or V-5014B

and V-5054D cameras with ﬁrmware Version D4.2.1_20200818_DMP and higher, the default password is scw

plus the last six alphanumeric characters in the camera’s MAC address. As an example, if the MAC address

1A:2B:3C:4D:5E:6F, the default password is scw4D5E6F.

For conﬁguration speciﬁcs, refer to Table 1.

V-4408D INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 3

4000 Series: Connect a Camera Directly to the NVR

On the NVR monitor, make sure Plug and Play is selected as the adding method for the port that you want

the camera to use. No further conﬁguration is required.

5000 Series: Connect a Camera Directly to the NVR

When connecting a 5000 Series camera directly to the NVR, you’ll need to start by conﬁguring the camera

with a static IP address before connecting the camera directly to the NVR.

Set Up a Static IP

Note: Leave the camera disconnected from the NVR until you’ve ﬁnished conﬁguring the static IP.

1. On the NVR monitor, right-click in the window and select Menu. Enter the username and password that

you used during activation.

2. Select Camera to open the Camera Management window. Find the NVR camera port that you want to

connect the camera to and record its IP address.

Note: This IP address may be in a dierent address range than other IP addresses used on the network.

3. Connect the camera to the local network.

4. Using the camera’s MAC address, determine the IP that the camera is currently using.

5. Open a web browser and enter the camera’s IP address.

6. Enter the camera’s default username and password.

7. Go to Network > Network Settings.

8. In Network Type, select Static.

9. In IP setup, enter the IP address the NVR assigned to the port that you want to use.

10. Change the gateway address to the ﬁrst address on the NVR’s subnet: 192.168.254.1.

11. Press Apply. Disconnect the camera from the network, then connect it to the NVR port that you want

to use.

Add the Camera to the NVR

1. On the NVR monitor, right-click in the window and select Menu.

2. Select Camera to open the Camera Management window.

3. Select Edit to open the Edit IP Camera window.

4. Set the Adding Method to Manual.

5. Use the information from Table 1 to set the Management Port and Protocol, then enter the username

and password.

6. Press OK. The NVR attempts to connect to the camera.

MODEL MANAGEMENT

PORT

PROTOCOL USERNAME PASSWORD

V-4022C 8000 Hikvision admin blank

V-4052D 8000 Hikvision admin blank

V-4060DB 8000 ONVIF admin admin veriﬁcation (See “Admin Veriﬁcation”)

V-4072MD 8000 Hikvision admin blank

V-5012B* 80 ONVIF scwuser scw12345user or

scw + [last 6 of MAC uppercase]

V-5014B* 80 ONVIF scwuser scw12345user or

scw + [last 6 of MAC uppercase]

V-5052D* 80 ONVIF scwuser scw12345user or

scw + [last 6 of MAC uppercase]

V-5054D* 80 ONVIF scwuser scw12345user or

scw + [last 6 of MAC uppercase]

*Default password depends on ﬁrmware version. Refer to “5000 Series Default Passwords” for more information.

Table 1: Camera Conﬁguration Speciﬁcs

LT-1779 20443

V-4408D NVR

Speciﬁcations

Temperature Range: 14°F to 131°F (-10°C to 55°C)

Humidity Range: 10% to 90%

Dimensions: 2.0”H x 15.2”W x 12.4”D

Compatibility

SecureCom Wireless Video Cameras:

• V-4022C Indoor Cube Camera

• V-4052D Indoor Dome Camera

• V-4060DB Video Doorbell

• V-4072MD Indoor/Outdoor Mini Dome Camera

• V-5012B Indoor/Outdoor HD Video Camera

• V-5014B Indoor/Outdoor HD Video Camera

• V-5052D Indoor/Outdoor HD Video Camera

• V-5054D Indoor/Outdoor HD Video Camera

INTRUSION • FIRE• ACCESS• NETWORKS

2500 North Partnership Boulevard

Springﬁeld, Missouri 65803-8877

800.641.4282 | DMP.com

NAME THE CAMERAS

Remotely

1. Log in to dealer.securecomwireless.com.

2. Click the customer’s system account number. All cameras connected to the V-4408D should display on

the System Information screen.

3. Select Edit to edit the NVR.

4. Click on the default camera name to change the name of each camera.

Locally

1. Right-click the screen and select Menu from the dropdown menu.

2. Select Camera.This will take you to the Camera Management screen. From this screen, you are able to

conﬁgure the camera to suit the installation.

3. Select OSD to edit the camera. See “Connect a Camera over Network to the NVR”.

4. Click on the default camera name to change the name of each camera.

Connect a Camera over Network to the NVR

Refer to Table 1 throughout the following steps.

1. On the NVR monitor, choose Manual as the method to add a 4000 Series camera, a V-4060DB

doorbell, or a 5000 Series camera.

2. Open a web browser and enter the camera’s IP address.

3. Enter the camera’s default username and password.

4. Use the information from Table 1 to set the Management Port and Protocol.

5. Select the Channel Port and TransferProtocol, then enter the username and password.

6. Press OK. The NVR attempts to connect to the camera.

Add an ONVIF Camera in Dealer Admin

Refer to Table 1 throughout the following steps.

1. Log in to dealer.securecomwireless.com.

2. Click the customer’s system account number. All cameras connected to the V-4408D should display

on the System Information screen.

3. Select Edit to edit the NVR.

4. Select the Add icon to add the camera.

5. Enter the name and IP port.

6. At Camera Type, select the type. For the doorbell, select Standard Hikvision. For a 5000 Series

camera, select Other ONVIF. For a 4000 Series camera, select Securecom Hikvision.

7. Select Save.

Autres manuels SECURECOM Instrument de mesure

SECURECOM

SECURECOM SS21-GSM M2 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur