Securam ProLogic L66 Manuel utilisateur

ProLogic L66 Operation Instructions

Document No: EC-0601A-L66-180510

Version No: V1.01

1.0 System Installation

1.1 System Components

1.2 Pairing the EntryPad with the Lock(s)

1.3 Lock and EntryPad Installation

1.4 Installing Battery

1.5 Test Lock Operation

2.0 Code Length Options

2.1 PW L – 6 / Users 10

2.2 PW L – 8 / Users 30

2.3 PW L – 6 / Users 30

3.0 Lock Operation

3.1 Opening the Lock

3.2 Opening the Lock in Time Delay

3.3 Opening the Lock Under Duress

3.4 Opening the Lock in Dual Control

3.5 Opening the Lock with a Multi-Lock System

4.0 Set Date and Time

4.1 Set Clock Time

4.2 Show Clock Time

4.3 DayLight Savings Time

5.0 Code Management

5.1 Enrolling New users

5.2 Change Code

5.3 Delete One User

5.4 Delete All Users

5.5 Disable/Enable User

5.6 Obfuscate Code Entry

5.7 Set ID01 to Master

5.8 Renew Code Period

6.0 System Identification

6.1 System Info

7.0 Time Delay

7.1 Set/Cancel Time Delay

7.2 Set Duress Time Delay

7.3 Setting Time Delay Override Users

8.0 Audit Trail Functionality

8.1 Show Audit Trail

8.2 Uploading Audit Trail

9.0 Manager Mode

9.1 Enable Manager Mode

9.2 Disable Manager Mode

10.0 Single or Dual Control

10.1 Enable Dual Mode

10.2 Dual Mode Group ID

11.0 Setting Time Lock

11.1 Set Timer

11.2 Set Time Table

11.3 Set Holidays

11.4 See Timer

12.0 Door Management

12.1 Max. Door Open Time

12.2 Configuring a Multi-lock system

12.3 Set Number of Locks

12.4 Authorize Locks

12.5 Enable Sequence

13.0 Duress Management

13.1 Duress Setup and Wiring Configuration

13.2 Duress Code Shift

14.0 Wireless Management

14.1 Set Device ID

14.2 Set Host ID

14.3 Wireless Connection

15.0 Data Management

15.1 Restore Data

15.2 Backup Data

15.3 Encryption Key Set

ProLogic L66 Operation Instructions

16.0 Recovering the System – Reset to Default

16.1 Recovery Code Set

16.2 Recover System

16.3 Disable Recover

16.4 Mechanical Reset

17.0 System Testing

17.1 Cycle Testing

17.2 Hardware Testing

18.0 Menus

18.1 The ProLogic L66 Menus

IMPORTANT: It is imperative that all programming be completed with the safe

door in its open position, such that the programmer can gain access to the lock

body in the event of an incorrect programming.

1.0 System Installation

1.1 System Components

The system consists of (1) EntryPad – Part # EC-0601A-L66 plus (1) or more Lock bodies as follows:

 SwingBolt – Part # EL-0601

 SwingBolt with Status Sensor – Part # EL-0601-S

 DeadBolt – Part # EL-0701

 SpringBolt – Part #EL-0801

Note: The ProLogic L66 can control up to 4 locks when used in conjunction with the Expansion Box –

Part # CB11-1T4. (If setting up a multi-lock system, please refer to Section 11.2 – Multi-Lock Systems)

1.2 Pairing the EntryPad and the Lock

SecuRam safe lock systems can operate in two different modes depending upon the type of EntryPad

being used with the lock body. The ProLogic L66 is a digital lock system and therefore the lock must also

be programmed in digital mode. Both modes follow the same steps to reset / set which is done by

following the steps detailed below:

Step 1: Ensure the battery is connected to the Entry Pad.

Step 2: Ensure the lock cable is disconnected from the lock body.

Step 3: Locate the Reset Hole on the back of the lock (under the QC sticker).

ProLogic L66 Operation Instructions

Step 4: Using a paper clip depress the reset button, inside the reset hole, 3 times to dissipate

any latent energy in the lock.

Step 5: Now depress the reset button and hold.

Step 6: While continuing to depress the reset button, connect the lock cable to the lock body.

Step 7: Continue to hold down the reset button for 5 seconds and then release.

Step 8: Verify that the pairing has been completed, by opening the lock with the default code

111111.

Step 9: Press any button on the EntryPad to initiate a lock communication test. The EntryPad

will display the following information:

Followed by:

Enter a valid code to test the lock.

The Default codes are as follows:

 Super Code (ID00) is 111111

 Manager Code (ID01) is 123456

Upon entry of a valid code, the lock will open. If the lock does not open and the LCD screen

displays the message “Fail to Link with Lock”, repeat the reset procedure. Be sure to hold down

the reset button through steps 5-7.

If you have difficulty resetting the lock, please call SecuRam Tech Support at (805) 988-8088 or email

info@securamsys.com.

1.3 Lock and EntryPad Installation

Included within your installation kit are (2) shoulder bolts and (3) lock mounting bolts.

 Install the shoulder bolts on the safe door in the pre-drilled holes above and below the spindle

hole.

 Now insert the lock cable (attached to the EntryPad) through the spindle hole.

 On the backside of the safe door, you will see the lock mounting plate and the predrilled lock

mounting holes.

 Connect the lock cable to the lock body and position the lock body appropriately on the lock

mounting plate.

ProLogic L66 Operation Instructions

 Ensure that the lock cable is positioned so that it lies in the channel on the back of the lock. This

channel is provided to protect the lock cable from damage or crimping during installation.

 Using the provided lock bolts, secure the lock body to the mounting plate.

Note: it is very important to ensure that there is an adequate gap between the lock bolt and the

boltwork. This gap must be 0.125”.

1.4.1 Installing the Battery – Standard Battery Compartment (located on the back of the EntryPad)

 Connect the battery terminal clip to the 9V battery. (Duracell or Energizer brands are

recommended).

 Position the battery so that the terminals are in the downward position and push the battery

into the battery compartment. See Fig. 1.

 Carefully tuck the excess lock cable into the cavity on the back of the EntryPad and install the

EntryPad on the shoulder bolts. See Fig. 2.

 Be careful not to crimp or damage the lock cable upon EntryPad installation.

1.4.2 Installing the Battery – SureLock Battery Compartment (removable battery compartment)

 Locate the SureLock Battery Compartment at the 5 o’clock position of the EntryPad. See Fig. 3.

 Release the latch of the battery compartment, by pulling lever downward. See Fig 4.

 Pull out the battery compartment from the bottom of the EntryPad. See Fig 5.

 Install a new 9V alkaline battery (Duracell or Energizer brands are recommended) into the

compartment. The battery compartment will only receive the battery when the positive and

negative terminals are oriented correctly. See Fig. 6

 Put the battery compartment back into the EntryPad. Push the latch of the battery

compartment up until it snaps closed. See Fig. 3

ProLogic L66 Operation Instructions

1.5 Testing the Lock Operation

The ProLogic L66 comes with two factory default codes:

• Super Code (ID00) is 111111

• Manager Code (ID01) is 123456

Enter one of the valid codes to verify that the communication between the lock and EntryPad. The lock

will open.

2.0 Code Length Options

IMPORTANT: This must be completed before any programming.

The ProLogic L66 allows you the ability to select the code length for all safe lock operators and the total

number of users allowable on the lock. Setting the code length and number of Users is a global setting

and applies to all safe lock operators.

There are 3 options available as follows:

 Code Length 6 digits – 10 total codes available - This is the default mode and meets the UL

requirement.

 Code Length 8 digits – 30 total codes available – This mode also meets the UL requirement.

 Code Length 6 digits – 30 total codes available – This mode does not meet the UL requirement.

2.1 PW L – 6; Users – 10 – This is the default mode

NOTE: This operation must be performed with the safe door open and with access to the back of the

lock, as a mechanical reset must be performed during this programming sequence.

Step1: Press the Menu/OK button.

Step 2: Using the  and , scroll to the System Menu and Press Menu/OK.

ProLogic L66 Operation Instructions

Step 3: The display will prompt you to enter a valid code. Enter the Super Code (ID00) only .

This function is not available to Manager Codes ID01 or ID02. The “Select Menu” message will

be displayed as follows:

Step 4: Scroll  and  to the menu selection “PW L – 6; Users – 10” and Press OK

Step 5: The LCD will display a warning followed by “Delete All Users?”, press OK to confirm.

All users have been deleted.

IMPORTANT: The LCD will advise if a reset is required to finalize the programming. If required, follow

the Mechanical Reset procedure outlined in 15.4 Mechanical Reset.

The code length will now be 6 digits and the total available users will be 10.

The Super Code ID00 will now be 1-1-1-1-1-1

The Manager Code ID01 will now be 1-2-3-4-5-6

2.2 PW L – 8; Users – 30

NOTE: This operation must be performed with the safe door open and with access to the back of the

lock, as a mechanical reset must be performed during this programming sequence.

Step1: Press the Menu/OK button.

Step 2: Using the  and , scroll to the System Menu and Press Menu/OK.

Step 3: The display will prompt you to enter a valid code. Enter the Super Code (ID00) only .

This function is not available to Manager Codes ID01 or ID02. The “Select Menu” message will

be displayed as follows:

ProLogic L66 Operation Instructions

Step 4: Scroll  and  to the menu selection “PW L – 8; Users – 30” and Press OK

Step 5: The LCD will display a warning followed by “Delete All Users?”, press OK to confirm.

All users have been deleted.

IMPORTANT: The LCD will advise if a reset is required to finalize the programming. If required, follow

the Mechanical Reset procedure outlined in 15.4 Mechanical Reset.

The code length will now be 8 digits and the total available users will be 30.

The Super Code ID00 will now be 1-1-1-1-1-1-0-0

The Manager Code ID01 will now be 1-2-3-4-5-6-0-0

The Default Recovery Code will be 9-9-9-9-9-9-0-0

The Default Encryption Code will be 6-8-5-1-9-8-0-0

2.3 PW L – 6; Users – 30

NOTE: This operation must be performed with the safe door open and with access to the back of the

lock, as a mechanical reset must be performed during this programming sequence.

Step1: Press the Menu/OK button.

Step 2: Using the  and , scroll to the System Menu and Press Menu/OK.

Step 3: The display will prompt you to enter a valid code. Enter the Super Code (ID00) only .

This function is not available to Manager Codes ID01 or ID02. The “Select Menu” message will

be displayed as follows:

ProLogic L66 Operation Instructions

Step 4: Scroll  and  to the menu selection “PW L – 6; Users – 30” and Press OK

Step 5: The LCD will display a message to indicate that this setting does not meet the UL

requirement.

Step 6: The LCD will then display a warning followed by “Delete All Users?”, press OK to

confirm.

All users have been deleted.

IMPORTANT: The LCD will advise if a reset is required to finalize the programming. If required, follow

the Mechanical Reset procedure outlined in 15.4 Mechanical Reset.

The code length will now be 6 digits and the total available users will be 30.

The Super Code ID00 will now be 1-1-1-1-1-1

The Manager Code ID01 will now be 1-2-3-4-5-6

3.0 Lock Operation

Upon initial power up, the LCD screen starts a communications test as shown below:

 Including Model Number

 Software Version Number

 No. of Users/ No. Users Programmed

 Lock ID#/Host ID#

 Model Name

ProLogic L66 Operation Instructions

 No. of Audit Events

After this initial power up it will also check to ensure that the system is communicating correctly. The

display will read “Link with Lock OK”.

If the Display reads: “Fail to Link with Lock” proceed to Section 1.2 entitled “Pairing the EntryPad and

the Lock”

3.1 Opening the Lock

The safe lock system has two default codes installed as follows:

• Super Code (ID00) 1-1-1-1-1-1

• Manager Code (ID01) 1-2-3-4-5-6

Step 1: Enter a valid code – for example ID00.

The display will read “ID00 Verified”.

And the Lock will open.

The display will read:

The lock will relock after 6 seconds.

Note: Time to relock is hard coded and cannot be changed.

3.2 Opening Lock with Time Delay Programmed

When Time Delay has been programmed, the user must enter a valid code.

Note: Users are defined as ID03- ID30

Wait through the preprogrammed time delay period, then enter the code again to open the lock safe, as

follows:

Step1: Enter a valid code

Note: ID00, ID01 and ID02 are Administrator users and will bypass Time Delay.

ID00

ProLogic L66 Operation Instructions

Step 2: Display will read “Time Delay Start”

Step 3: Display will flash on every 15 seconds, counting up until it reaches the preprogrammed

time delay value.

Note: Administrators can override Time Delay to open lock anytime.

Step 4: When Time Delay expires, the EntryPad will beep twice then display: “Time Window

XX:00”, indicating the length of time the User has to enter a valid user code to gain entry.

The Counter will count down until the Time Window has expired. A user code is used to open

the lock.

Step 5: Enter a valid Code to open the lock.

3.3 Opening the Lock Under Duress

The ProLogic L66 has a Duress Feature, which allows a User or Admin to open the lock and send a silent

Duress signal indicating that you are in danger. By default, the duress function is active and cannot be

disabled.

In Order to send a signal, the system must have a CB10 junction box installed and must be connected to

an alarm panel.

To Open the Lock under Duress:

Step 1: Enter a valid Code, but add or subtract 1 from the code. The Lock will open as normal and a

silent alarm will be issued.

Note: This will be logged as “Duress Unlock” in events.

For example, if your code is 123456; under Duress, enter 123455 or 123457 to send silent alarm.

Table des matières

Autres manuels Securam Verrouillage

Securam

Securam SH-TB01 Manuel utilisateur

Securam

Securam SafeLogic Basic Manuel utilisateur

Securam

Securam ProLogic B01 Manuel utilisateur

Securam

Securam SCANLOGIC FPC-1808-II-MB Manuel utilisateur

Securam

Securam ProLogic L02-C Manuel utilisateur

Securam

Securam ProLogic B22 Manuel utilisateur

Securam

Securam SafeLogic Xtreme Manuel du propriétaire

Securam

Securam ECSL-601 Manuel utilisateur

Securam

Securam ProLogic L22 Manuel utilisateur

Securam

Securam SafeLogic Basic Series Manuel utilisateur

Securam

Securam EM-1701A-R Manuel utilisateur

Securam

Securam SafeLogic TopLit Series Manuel utilisateur

Securam

Securam ScanLogic D66 Manuel utilisateur

Securam

Securam ScanLogic Optical Manuel d'installation

Securam

Securam ScanLogic B22 Manuel utilisateur

Securam

Securam D Series Manuel utilisateur

Securam

Securam FPC-0601A-D22 Manuel utilisateur

Securam

Securam SafeLogic C10 D-Drive Manuel utilisateur

Securam

Securam SafeLogic Basic Manuel utilisateur

Securam

Securam MANAGER Series Manuel utilisateur

Securam

Securam V8 Manuel technique

Securam

Securam SafeLogic Basic Manuel utilisateur

Securam

Securam SH-WB01 Manuel utilisateur

Securam

Securam ProLogic L01 Manuel utilisateur

Manuels Verrouillage populaires d'autres marques

Magic

Magic 105 Manuel utilisateur

Gantner

Gantner GAT NET.Lock 7020 System Guide rapide

Wittkopp

Wittkopp Insys 7202 Manuel utilisateur

Dorma

Dorma Studio Classic Manuel utilisateur

Sudhaus

Sudhaus 3003 Manuel utilisateur

Safety 1st

Safety 1st 48517 Manuel utilisateur

Pado

Pado FDS-10 Manuel utilisateur

Esco

Esco systeQ Series Manuel utilisateur

COMPX

COMPX National D8951 Manuel utilisateur

secureo

secureo Key Box Manuel utilisateur

Stock Loks

Stock Loks C8713 Manuel utilisateur

COMPX

COMPX 1T-058 Manuel du propriétaire

Auslock

Auslock T11 Manuel utilisateur

ELCOM

ELCOM 7205 Manuel utilisateur

Stealth SAFES

Stealth SAFES ShadowVault Manuel utilisateur

Knox

Knox KeySecure 5 Manuel utilisateur

Kwikset

Kwikset 48334/01 Manuel utilisateur

Metra Electronics

Metra Electronics Door Access Terminal Combo Manuel utilisateur