NW6000-7501 QIG
-1- -2- -3-
1. Overview
NW6000-7501 DNV GL Certied Managed PoE+ Switch is designed for
harsh environments to withstand vibration, shock, free fall and power
surges. The switch provides layer 2+ software features while operating
from a 24/48VDC power source, and has DNV GL Marine Approval and
Lloyd's Register Group Approval for safe and reliable marine
operations. It includes 8-port 10/100/1000Mbps PoE+ downlink and
4-port GbE SFP uplink with 30W per PoE+ port for powered devices.
2. Package Checklist
5.1 Wiring Power Input
5.1.1 The Switch with terminal block
You can use “PWR” for Primary Power input and “RPS” for Redundant
Power Input. Check the polarity while connecting.
Top view of Terminal Block is shown in the gure below:
3. Mounting and Dismounting to DIN-Rail
!ATTENTION:
The Switch is an open type device and shall be DIN-Rail
mounted or wall mounted (optional) in the cabinet and
the ambient temperature should not exceed the operating
temperature.
!
Terminal Block
Caution:
• Use copper conductors only
• Wiring cable temperature should
support at least 105°C
• Tighten the wire to a torque value 5lb
• The wire gauge for the terminal block
should range between 12~24 AWG
To insert power wire and connect the specied voltage range at a
maximum of 6A DC power to the power terminal block, follow the
steps below:
1. Use a at-head screwdriver to loosen the wire-clamp screws
2. Insert the negative/positive DC wires into the PWR-/PWR+
terminals, respectively
3. Tighten the wire-clamp screws to prevent the wires from loosening.
!ATTENTION:
Please use a power supply from 24~57VDC, the device
power shall be supplied by SELV circuit.
voltage. DO NOT use a voltage greater than what is specied on
the product label. Calculate the maximum possible current in each
power wire and common wire. Observe all electrical codes
dictating the maximum current allowable for each wire size. If
current exceeds the maximum rating, the wiring can overheat
causing serious damage to your equipment.
Please read and follow these guidelines:
• Use separate paths to route wiring for power and devices. If
power wiring and device wiring paths must cross make sure the
wires are perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power
wiring through the same wire conduit. To avoid interference,
wires with dierent signal characteristics should be routed
separately.
• You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of
thumb is that wiring that shares similar electrical characteristics
can be bundled together
• You should separate input wiring from output wiring
• We advise that you label the wiring to all devices in the system
!WARNING:
Safety measures should be taken before connecting the
power cable. Turn o the power before connecting
modules or wires. The correct power supply voltage is
listed on the product label. Check the voltage of your
power source to make sure that you are using the correct
5. Wiring requirements
The switch is shipped with the following items*.
If any of these are missing or damaged, please contact your customer
service representative for assistance.
• The Switch x 1
• DIN-Rail kit x 1
• Console Cable x 1
• Quick Installation Guide x 1
4. Grounding the switch
Grounding and wire routing help limit the eects of noise due to
electromagnetic interference (EMI). Run the ground connection from
the ground screw to the grounding surface prior to connecting
devices.
!ATTENTION:
A corrosion-free mounting rail is advisable. When installing,
make sure to allow for enough space between devices to
properly install the cabling. And provide ample space for
air ow.
!ATTENTION:
This product is intended to be mounted to a well-grounded
mounting surface such as a metal panel.
Mounting the switch
Place the switch on the DIN-Rail from above using the slot, push the
front of the switch toward the mounting surface until it snaps into
place with a click sound.
Dismounting the switch
Press the switch from top and pull out the lower edge of the switch
and then remove the switch from the DIN-Rail.
Panel view
Front ViewTop View
DIP Switches
USB
1
3
5
7
2
4
6
8
9 10
11 12
CONSOLE
RPS
PWR
ALM
POST
1000Mbps
(Green)
LNK/ACT
(Green)
24~57VDC
+
+
PWR
RPS
ALM
Grounding
Screw
Power Input
Terminal Block
OFF ON
1
2
SFP
ALM
POST
PWR
RPS
9 10 11 12
SFP
SFP
PoE
1
ALM
PWR
RPS2
Reset
1 2 34
5 6 7 8
PoE
1000
LNK/
ACT
Mounting the Switch
Click
Removing the Switch
NOTE: We strongly request that each Industrial PoE switch connects
to the individual power supply. Please don’t use one power supply to
two or more PoE switches at a time.
