Sealey AP1640 Manuel utilisateur

1.52M WOODWORKING BENCH WITH 4

DRAWERS

MODEL NO: AP1640

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,

and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY

WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this bench.

9Locate the bench in a suitable work area.

9Keep the work area clean, uncluttered and ensure there is adequate lighting.

WARNING! Use the bench on level and solid ground, preferably concrete.

9Keep the bench clean and tidy in accordance with good workshop practice.

9Keep children and unauthorised persons away from the work area.

8DO NOT use the bench for any purpose other than for which it is designed.

8DO NOT undertake work on the bench without the workpiece being adequately secured.

8DO NOT use the bench outdoors.

8DO NOT clean the bench with any solvents which may damage the surface or the protective coating on the worktop.

8DO NOT get the bench wet or use in damp or wet locations or areas where there is condensation.

2. INTRODUCTION

Made from Rubber Wood. Features tool well, shelf, 4 tool drawers, front vice, four metal bench stops and four wooden board jacks.

Supplied with 4 Wooden Pegs and 4 Anvil Pegs.

3. SPECIFICATION

Model No: ................................................................. AP1640

Overall Size (W x D x H): .......... 1520mm x 620mm x 820mm

Worktop: .........................................................1520 x 500mm

4. CONTENTS

Refer to

instruction

manual

AP1640 Issue:1 17/05/22

Original Language Version

Tool Well: ........................................................ 1110 x 410mm

Drawer(x4): ...............................................460 x 390 x 80mm

Vice (x1):...............................280mm wide x 180mm opening

Part

no.

Description Quantity

1 Table top 1

2 Shelf 1

3 Cross brace 2

4 Leg 2

5 Vice 1

6 Screw 60mm 4

7 Bolt 90mm 4

8 Connecting nut 8

9 Hex wrench 50mm 1

10 Wood peg 4

11 Anvil peg 4

12 Vice screw & washer 1

13 Screw 30mm 32

14 Screw 35mm 8

15 Sliding partition 1

16 Lower support 2

17 Drawer front panel (P1) 4

18 Drawer back panel (P2) 4

19 Drawer panel (P3) 4

Original Language Version

20 Drawer slot panel (P4) 4

21 Drawer bottom (P5) 4

22 Drawer handle 4

23 Drawer screw (40mm) 8

5. ASSEMBLY

5.1.

5.2.

5.3.

5.4.

Step 1: Insert the cross nut with groove (8) into the

frame strut (3). Align the cross nut so that the groove is

horizontal.

Step 2: Fasten the frame to the foot (4) with 2pcs of 90mm

screws (7).

Step 3: After both feet have been attached to the frame

strut, the shelf (2) is pushed into the groove.

Step 4: Align the second frame strut (3) and fasten it with

the connecting nuts with groove (8) and 2 pcs of 90mm

screws (7) on the foot (4). The shelf must snap into the

groove of the frame strut.

Step 5: The lower support (16) is attached to the front with

4 pcs of 35mm screws (14) at both ends of the feet.

Step 6: The lower support(16) is also attached to the

partition wall with rails (15) using 2 pcs of 35mm screws

(14).

AP1640 Issue:1 17/05/22

Original Language Version

Step 7: The legs are then attached to the worktop with 4

pcs of 60mm screws (6), 2 pcs per leg.

Step 8: The partition is also attached to the frame with 2

pcs of 35mm screws (14). WARNING! there are no pre

drilled holes.

Step 9: Attach handles (22) to the front of the drawer (17)

with 8 pcs of 40mm drawer screws (23), 2 pcs per drawer.

Step10: The two side parts of the drawer (19 & 20) are

attached to the front of the drawer with 2 pcs of 30mm

screws (13) per side, 4 pcs per drawer.

Step11: The back of the drawer (18) is attached to the two

side parts by using 4 pcs of 30mm screws (13), 2 pcs per

side. Then insert the bottom of the drawer. Step12: After installing the drawers, check whether the

inner tracks of the drawer pull outs are pushed all the way

forward if not, then push all the way forward.

Step13: When inserting the drawers, make sure the runner

clip is facing forwards see picture, then slide the drawers

into the guides.

Step14: Fasten the holding rods (10) and the bench hooks

(11) in the holes provided in the worktop.

AP1640 Issue:1 17/05/22

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to

a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely

unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids

according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior

notice.

Important: No Liability is accepted for incorrect use of this product.

Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

AP1640 Issue:1 17/05/22

Original Language Version

Autres manuels Sealey Rangement des outils

Sealey

Sealey AP0618.V4 Manuel utilisateur

Sealey

Sealey PTB39003 Manuel utilisateur

Sealey

Sealey AP12600 Manuel utilisateur

Sealey

Sealey AP22 Series Manuel utilisateur

Sealey

Sealey AP165WB Manuel utilisateur

Sealey

Sealey AP335M Manuel utilisateur

Sealey

Sealey SM30.V2 Manuel utilisateur

Sealey

Sealey PTB104008 Manuel utilisateur

Sealey

Sealey AP1010 Manuel utilisateur

Sealey

Sealey SL1D.V2 Manuel utilisateur

Sealey

Sealey AP6310BE Manuel utilisateur

Sealey

Sealey AP1520.V2 Manuel utilisateur

Sealey

Sealey AP1205 Manuel utilisateur

Sealey

Sealey AP28102BWS Manuel utilisateur

Sealey

Sealey SC01 Manuel utilisateur

Sealey

Sealey AP850MB Manuel utilisateur

Sealey

Sealey AP02WC Manuel utilisateur

Sealey

Sealey AP3020 Manuel utilisateur

Sealey

Sealey PTB104008SS Manuel utilisateur

Sealey

Sealey AP2010 Manuel utilisateur

Sealey

Sealey AP0615 Manuel utilisateur

Sealey

Sealey APMS20 Manuel utilisateur

Sealey

Sealey SC01.V2 Manuel utilisateur

Sealey

Sealey APMS01 Manuel utilisateur

Manuels Rangement des outils populaires d'autres marques

Ryobi

Ryobi RWB03 Manuel utilisateur

Husky

Husky H27CH5TR4BGK Manuel utilisateur

Scheppach

Scheppach ts 2100 Manuel utilisateur

Cornwell Tools

Cornwell Tools CTB360AKBK Manuel utilisateur

DIVERSIFIED WOODCRAFTS

DIVERSIFIED WOODCRAFTS SHAIN GSB-6024 Manuel utilisateur

Cassese

Cassese CS200 CART Manuel utilisateur

Kendall Howard

Kendall Howard ESDW-9630-1000 Manuel utilisateur

Lista

Lista Align Instructions de montage

Workzone

Workzone 99609 Manuel utilisateur

Stanley

Stanley STST83800-1 Manuel utilisateur

Homak

Homak PROFESSIONAL Series Manuel du système

Perel

Perel ROLLER SHUTTER STORAGE CABINET Manuel utilisateur

Husky

Husky H5CH2R Manuel utilisateur

BGS technic

BGS technic 4107 Manuel utilisateur

Clarke

Clarke CWB1250 Manuel utilisateur

Ryobi

Ryobi RWB02 Manuel utilisateur

Husky

Husky H52CH6HDV3WHT Manuel utilisateur

General International

General International Excalibur 40-100 Manuel de la liste des pièces