Sealey MES02 Manuel utilisateur
INSTRUCTIONS FOR
ENGINE REBUILD STAND - MULTICYLINDER
MODEL NO: MES02
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure all Health and Safety, local authority, and general workshop practice regulations are strictly adhered to when using this
equipment.
8DO NOT use unit if damaged.
9Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9Keep the stand clean for best and safest performance.
9Locate the stand in a suitable work area. Keep area clean and tidy and free from unrelated materials. Ensure there is adequate lighting.
9Use on a firm, level surface capable of sustaining the stand and the load.
9Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9Ensure all non-essential persons keep a safe distance whilst the stand is in use.
9Lock ratchet in position with locking pin before fixing a load and ensure the engine is centred and securely mounted.
9Ensure the stand and load are stable.
9DO NOT allow untrained persons to use the stand.
8DO NOT exceed the rated capacity of 75kg.
8DO NOT use the stand for purposes other than those for which it is designed.
9When not in use store stand in a safe, dry, childproof area.
2. INTRODUCTION
Suitable for a wide variety of engines and transmissions. features fully adjustable lower mounting arms and swivel castors, capable of supporting
larger (maximum 75kg) multi cylinder engines. Supports can rotate for accessibility to all parts of the engine.
3. SPECIFICATION
Model no: .................................................................. MES02
Maximum capacity: ........................................................ 75kg
Min./Max. width engine mounting brackets: ........ 150-360mm
Min./Max. length:................................................. 550/940mm
Min./Max. height:................................................. 540/795mm
MES02| Issue 1 15/03/16
Original Language Version
© Jack Sealey Limited
Refer to
Instruction
Manual
4. ASSEMBLY
Refer to g.1.
4.1. Insert bottom frame (5) into bottom frame (2). secure with locking bolt (4).
4.2. Bolt upright posts (1) to either end of bottom frame assembly (5 & 2) using bolt (9), washer (7) and nut (6).
4.3. Insert expansion posts (11 & 12) into upright posts (1), secure with pins (10) and R clips.
4.4. Insert rotary frame 1 (23) into expansion post (11). Secure rst with circlip (25) and then bolt (13) washer (14) and nut (15).
4.5. Insert rotary frame 2 (24) into expansion post (12). Secure rst with circlip (25) and then bolt (13) washer (14) and nut (15).
4.6. Use ratchet (16) and locking bolt (4) on top of expansion post 2 (12) to adjust angle of rotary frames (24 & 25).
4.7. Fit wheels (8) using washer (7) and nut (6).
4.8. Slide supporting frames (21 & 22) onto rotary frames 1 & 2 (23 & 24), secure with bolts (20).
4.9. Secure all fasteners.
5. OPERATION
Refer to gs. 2 & 3.
5.1. Use original engine mounting bolts or studding, washers
and nuts of appropriate size to secure the engine to the stand
using supporting frames (21 & 22).
Y
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
Sole UK Distributor, Sealey Group.
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk.
IP32 7AR
www.sealey.co.uk
sales@sealey.co.uk
01284 757500
01284 703534
Web
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
Fig.2
Fig.3
MES02| Issue 1 15/03/16
Original Language Version
© Jack Sealey Limited
Fig.1
Table des matières
Autres manuels Sealey Support et étagère
Sealey
Sealey AS20 Manuel utilisateur
Sealey
Sealey ES300A.V2 Manuel utilisateur
Sealey
Sealey APMF Manuel utilisateur
Sealey
Sealey AS15000 Manuel utilisateur
Sealey
Sealey MK61.V2 Manuel utilisateur
Sealey
Sealey MK54.V3 Manuel utilisateur
Sealey
Sealey BS102 Manuel utilisateur
Sealey
Sealey AS10H.V2 Manuel utilisateur
Sealey
Sealey ES900F.V2 Manuel utilisateur
Sealey
Sealey MS063A Manuel utilisateur
Sealey
Sealey ASC50 Manuel utilisateur
Sealey
Sealey MK74 Manuel utilisateur
Sealey
Sealey MPS3 Manuel utilisateur
Sealey
Sealey AS2000HS Manuel utilisateur
Sealey
Sealey BS104 Manuel utilisateur
Sealey
Sealey ASH4000 Manuel utilisateur
Sealey
Sealey AP6350.V3 Manuel utilisateur
Sealey
Sealey MK56.V3 Manuel utilisateur
Sealey
Sealey STR003E Manuel utilisateur
Sealey
Sealey MK79 Manuel utilisateur
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
