Sealey AK98943 Manuel utilisateur
INSTRUCTIONS FOR:
VACUUM SUCTION CUP - PAIR
MODEL No: AK98943
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/
OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
2. INTRODUCTION & SPECIFICATION
Original Language Version AK98943 Issue: 1 - 24/09/13
© Jack Sealey Limited
Twin proled rubber suction cups designed for strength and reliability. Ideal for windscreen installation and glass transportation.
Capable of lifting 30kg from a horizontal position. Also suitable for other non-porous at surfaces such as sheet metal and tiles.
WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using
this tool.
DO NOT use the suction cup if any parts are damaged or missing as this may cause failure and/or personal injury.
Before each use, check condition of suction cup. Examine rubber pads for excessive glaze, cuts or roughness. If any
component is worn or damaged replace immediately.
DO NOT clean the suction cup with solvents or other harsh chemicals.
Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
WARNING! Always wear approved eye, face and hand protection when using the suction cup.
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
Maintain correct balance and footing. DO NOT over reach, ensure the floor is not slippery, wear non-slip footwear.
Keep children and unauthorised persons away from the working area.
Ensure workpiece is secure before attaching and using the suction cup.
WARNING! Ensure that the surface to which the suction cup is to be attached is non-pourous, clean, dry and free from oil
and grease.
DO NOT exceed the maximum pull capacity of the suction cup.
DO NOT use the suction cup for any purpose other than that for which it is designed.
DO NOT use the suction cup when you are tired or under the influence of alcohol, drugs or intoxicating medication.
When not in use, store in a safe, dry, childproof location.
DO NOT use any sharp object to loosen the suction cup as it may damage the rubber and prevent the tool from creating
suction.
DO NOT attempt to attach the suction cup to a person as severe bruising and/or damage to internal organs can occur.
DO NOT allow anything to interfere with the free movement of the plunger whilst the suction cup is attached to a surface.
Keep fingers clear of suction release tag during use.
DO NOT allow anything else to touch the release tab whilst in the process of lifting e.g. other lifting gear or adjacent fixtures
and fittings.
Model No;............................................................AK98943
Cup ø: ................................................................ 150mm
Maximum Lift Capacity:................................30kg (From Horizontal Position)
4. MAINTENANCE
3. OPERATION
WARNING! Ensure that you read, understand and apply Section 1 safety instructions.
The suction cup is designed to work best on float glass at a room temperature of 20ºC. Cold temperatures, humidity and
other surface contamination may reduce the holding capacity of the tool. The tool may not be as effective on other sheet
materials such as plastic and metal. Moisture and other contaminants will also reduce the slip resistance of the cup.
WARNING! This is a hand tool and must not be used in conjunction with a crane or any other lifting device.
3.1 Ensure that the workpiece to be moved is clean, dry and free from oil and grease.
3.2 Remove the protective cover from the suction cup.
3.3 Holding the handle, firmly push the suction cup onto the material and hold it there under pressure.
3.4 With your other hand, pump the plunger until it recedes into the barrel and the red line disappears from view. The suction cup
should now be firmly attached and ready for use.
3.5 Always keep the plunger in view during moving/lifting. Should the plunger begin to rise and the red line reappears, this
indicates a loss of suction and you should immediately put down the load.
3.6 Check that the suction cup and surface of the material are clean and free from any foreign bodies or imperfections.
When satisfied, reattach the suction cup as previously described.
NOTE: The suction cup is designed for lifting, carrying and holding objects for a short period of time only. If circumstances cause
an object to be held for longer than expected, the grip must be checked frequently with reference to the plunger position and
the visibility of the red line.
3.7 Only release the suction cup when the load has been set down. To release the suction cup from the surface to which it is
attached, lift the release tag at the side of the cup. DO NOT use any sharp object to loosen the suction cup as it may
damage the rubber and prevent the tool creating suction.
3.8 Refit the protective cover onto the suction cup and store it in a clean, dry, childproof location.
4.1 Check condition of suction cup regularly, if damaged replace using genuine parts only.
4.2 Always keep suction cup clean and free of oil and grease. Clean regularly with a non-aggressive cleaner.
4.3 In order to preserve elasticity, do not expose rubber pads to sunlight over an extended period of time.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
sales@sealey.co.uk
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
Original Language Version AK98943 Issue: 1 - 24/09/13
© Jack Sealey Limited
Parts support is available for this product. To obtain a parts listing and/or
diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or phone 01284 757500.
Table des matières
Autres manuels Sealey Système de levage
Sealey
Sealey MC390.V2 Manuel utilisateur
Sealey
Sealey FLR680T Manuel utilisateur
Sealey
Sealey LS501 Manuel utilisateur
Sealey
Sealey MC365 Manuel utilisateur
Sealey
Sealey HPT300 Manuel utilisateur
Sealey
Sealey MC680A Manuel utilisateur
Sealey
Sealey EVBT1000 Manuel utilisateur
Sealey
Sealey MC390 Manuel utilisateur
Sealey
Sealey MC480.v2 Manuel utilisateur
Sealey
Sealey MC450 Manuel utilisateur
Sealey
Sealey MC480.V3 Manuel utilisateur
Sealey
Sealey MC401.V3 Manuel utilisateur
Sealey
Sealey Quality MACHINERY MC402.V3 Manuel utilisateur
Sealey
Sealey MC680E Manuel utilisateur
Sealey
Sealey MC135 Manuel utilisateur
Sealey
Sealey MC500 Manuel utilisateur
Sealey
Sealey TD1202S Manuel utilisateur
Sealey
Sealey WD80 Manuel utilisateur
Sealey
Sealey PPL01 Manuel utilisateur
Sealey
Sealey DH02 Manuel utilisateur
Manuels Système de levage populaires d'autres marques
morse
morse 82H-124 Manuel utilisateur
Braun
Braun NL955 Series Manuel utilisateur
haacon
haacon 1889.10 Manuel utilisateur
Protekt
Protekt AT 252 Manuel utilisateur
R. Beck Maschinenbau
R. Beck Maschinenbau HS 600 Manuel utilisateur
Nova Technology International, LLC
Nova Technology International, LLC NAS Series Manuel utilisateur
Genie
Genie Z-60/34 Manuel utilisateur
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Manuel utilisateur
Custom Equipment
Custom Equipment Hy-Brid 3 Series Manuel de programmation
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Manuel de programmation
