Seagull Models JU-87 STUKA Manuel utilisateur

ASSEMBLY MANUAL

Code: SEA284

“ Graphics and specications may change without notice “ .

JU-87 STUKA GIANT SCALE

Specications:

Wingspan---------------90 in (228.6 cm).

Wing area---------------1328.7 sq.in (85.7 sq.dm).

Weight-------------------17.6 lbs (8.0 kg).

Length-------------------68.3 in (173.4 cm).

Gasoline Engine--------38-50cc

Radio--------------------7 channels with 7 servos.

JU-87 Instruction Manual.

ank you for choosing the JU-87 ARF by SG MODELS . e JU-87 was designed

with the intermediate/advanced sport yer in mind. It is a semi scale airplane which

is easy to y and quick to assemble. e airframe is conventionally built using balsa, ply-

wood to make it stronger than the average ARF, yet the design allows the aeroplane to be

kept light. You will nd that most of the work has been done for you already. e motor

mount has been tted and the hinges are pre-installed. Flying the JU-87 is simply a joy.

is instruction manual is designed to help you build a great ying aeroplane. Please read

this manual throughly before starting assembly of your JU-87 . Use the parts listing below to

indentify all parts.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & REPONSIBILITY.

If you are inexperienced with basic R/C ight we strongly recommend you contact your R/C

supplier and join your local R/C model Flying Club. R/C Model Flying Clubs oer a variety of

training procedures designed to help the new pilot on his way to successful R/C ight. ey

will also be able to advise on any insurance and safety regulations that may apply.

INTRODUCTION.

WARNING.

KIT CONTENTS

KIT CONTENTS.

SEA284 JU-87 STUKA GIANT

1. Fuselage

2. Wing set

3. Tail set

4. Canopy

5. Cowling

6. Pilot

7. Aluminum wing tube

8. Wheel pants

ADDITIONAL ITEMS REQUIRED.

TOOLS & SUPPLIES NEEDED.

in cyanoacrylate glue.

Medium cyanoacrylate glue.

30 minute epoxy.

5 minute epoxy.

Hand or electric drill.

Assorted drill bits.

Modelling knife.

Straight edge ruler.

2mm ball driver.

Phillips head screwdriver.

220 grit sandpaper.

90° square or builder’s triangle.

Wire cutters.

Masking tape & T-pins.

read-lock.

Paper towels.

�38-50cc gasoline engine.

�Computer radio with 7 servos.

�Glow plug to suit engine.

�Propeller to suit engine.

�Protective foam rubber for radio

system.

HINGING THE AILERON.

2x10mm

Note: adjust decal rim straight away.

JU-87 Instruction Manual.

HINGING THE FLAP.

INSTALL THE AILERONS

CONTROL HORN.

Epoxy.

Aileron control horn.

Flap control horn.

Epoxy.

Fiberglass control horn

INSTALL FLAP CONTROL HORN.

INSTALL LED LIGHT.

Install the ap control horn using the

same method as same as the aileron con-

trol horns.

JU-87 Instruction Manual.

Epoxy.

HINGING THE FLAP FOR

CENTER WING.

1) Repeat steps to install hinging for

center wing as same as steps done for ai-

lerons.

2) en, t the joiner wire into the ap of

center wing as below pictures.

3) Slide the wing tube into the wing tube

socket.

4) Slide the wing panel into position,

guiding the extensions from the side

wing into center wing.

INSTALLING THE AILERON SERVOS.

Because the size of servos dier, you

may need to adjust the size of the precut

opening in the mount. e notch in the

sides of the mount allow the servo lead to

pass through.

1) Using a small weight (Weighted fuel

pick-up works well) and string, feed the

string through the wing as indicated.

2) Place the servo between the mounting

blocks and space it from the hatch. Use a

pencil to mark the mounting hole loca-

tions on the blocks.

JU-87 Instruction Manual.

3) Use drill bit in a pin vise to drill the

mouting holes in the blocks.

4) Apply 2-3 drops of thin C/A to each

of the mounting holes. Allow the C/A to

cure without using accelerator.

C/A glue

5) Use dental oss to secure the connec-

tion so they cannot become unplugged.

6) Secure the servo to the aileron hatch

using Phillips screwdriver and the screws

provided with the servo.

7) Apply 1-2 drops of thin C/A to each of

the mounting tabs. Allow the C/A to cure

without using accelerator.

8) Remove the string from the wing at

the servo location and use the tape to at-

tach it to the servo extension lead. Pull

the lead through the wing and remove

the string.

9) Set the aileron hatch in place and use a

Phillips screw driver to install it with four

wood screws.

INSTALLING THE FLAP SERVO.

Repeat the procedure as above for the

ap servo.

2x10mm

AILERON PUSHROD

INSTALLATION.

Please see below pictures.

100mm

M3 clevis. M3 lock nut.

JU-87 Instruction Manual.

INSTALLING THE FLAP PUSHROD.

INSTALLING THE LANDING GEAR.

Repeat the procedure as aileron push-

rod.

100mm

M3 clevis. M3 lock nut.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Seagull Models Jouet

Seagull Models

Seagull Models SEA231 Manuel utilisateur

Seagull Models

Seagull Models Laser 200 Manuel utilisateur

Seagull Models

Seagull Models SEA 94 Pilatus PC-9 Manuel utilisateur

Seagull Models

Seagull Models SEA FURY Manuel utilisateur

Seagull Models

Seagull Models ZLIN 50 Manuel utilisateur

Seagull Models

Seagull Models SEA 324Y Manuel utilisateur

Seagull Models

Seagull Models DHC-1 Chipmunk Manuel utilisateur

Seagull Models

Seagull Models Extra 260 Manuel utilisateur

Seagull Models

Seagull Models YAK 54 Manuel utilisateur

Seagull Models

Seagull Models Mini MXS-R EP Manuel utilisateur

Seagull Models

Seagull Models Funfly 3D Manuel utilisateur

Seagull Models

Seagull Models ultra-jet Manuel utilisateur

Seagull Models

Seagull Models Seagull 2000 Manuel utilisateur

Seagull Models

Seagull Models Little Bunnt P-47D Manuel utilisateur

Seagull Models

Seagull Models CAP 232 Manuel utilisateur

Seagull Models

Seagull Models KA8-B Manuel utilisateur

Seagull Models

Seagull Models Arising Star Manuel utilisateur

Seagull Models

Seagull Models SEA230B Manuel utilisateur

Seagull Models

Seagull Models THUNDERBOLT P47G SNAFU 60 ARF Manuel utilisateur

Seagull Models

Seagull Models CHEROKEE Manuel utilisateur

Seagull Models

Seagull Models SEA 94 Pilatus PC-9 Manuel utilisateur

Seagull Models

Seagull Models MESSERSCHMITT BF109E 60 Manuel utilisateur

Seagull Models

Seagull Models HARRIER 3D Manuel utilisateur

Seagull Models

Seagull Models Turbo Raven Manuel utilisateur

Manuels Jouet populaires d'autres marques

marklin

marklin 37321 Manuel utilisateur

Canon

Canon PAPER CRAFT Manuel utilisateur

GREAT PLANES

GREAT PLANES Pitts M-12S Manuel utilisateur

NOCH

NOCH 14261 Manuel utilisateur

Hausler

Hausler 450 SE V2 Manuel utilisateur

Dynaflite

Dynaflite Daydream Manuel utilisateur

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuel

Kenner

Kenner Batman 63651 Manuel utilisateur

LEGO

LEGO 8527 Manuel utilisateur

iKarus

iKarus ECO 8 Manuel utilisateur

Multiplex

Multiplex EasyStar II Mode d’emploi

Walkera

Walkera 38 Mode d’emploi

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuel utilisateur

MD MXION SWD Manuel utilisateur

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuel utilisateur

marklin

marklin 39671 Manuel utilisateur

Meccano

Meccano 15103 Manuel utilisateur

LEGO

LEGO TECHNIC 8735 Manuel utilisateur