Seagate MEDALIST 1080SL Manuel utilisateur

. . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .

Medalist 1080sl

. . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . .

SCSI Interface Drive

. . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . .

Installation Guide

. . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .

Publication Number: 36325-001, Rev. A, August 1995

Seagate, Seagate Technology and the Seagate logo are regis-

tered trademarks of Seagate Technology, Inc. MedalistSL, Sea-

FAX, SeaFONE, SeaBOARD and SeaTDD are trademarks of

Seagate Technology, Inc. Other product names are registered

trademarks or trademarks of their owners.

Seagate reserves the right to change, without notice, product

offerings or specifications. No part of this publication may be

reproduced in any form without written permission from Seagate

Technology, Inc.

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 1

Read before you begin...

. . . . . . . . . . . . . . . . . . 3

Configuring the drive . . . . . . . . . . . . . . . . . . . . 5

Attaching cables . . . . . . . . . . . . . . . . . . . . . . 10

Mounting the drive . . . . . . . . . . . . . . . . . . . . . 11

Configuring the drive and computer . . . . . . . . . . . 12

System setup configuration . . . . . . . . . . . . . . . . 12

Low-level formatting . . . . . . . . . . . . . . . . . . . . 12

Partitioning . . . . . . . . . . . . . . . . . . . . . . . . 13

High-level formatting . . . . . . . . . . . . . . . . . . . 14

NonDOS operating systems . . . . . . . . . . . . . . . 15

Network installation . . . . . . . . . . . . . . . . . . . . 15

Basic troubleshooting . . . . . . . . . . . . . . . . . . . 16

Advanced troubleshooting . . . . . . . . . . . . . . . . 18

Technical support services . . . . . . . . . . . . . . . . 21

Storing and shipping your drive . . . . . . . . . . . . . . 24

Introduction

Thank you for choosing a Seagate drive. The purpose of this

guide is to assist you with installing your new hard drive. Its

organization outlinesthecomplete installation processfromhan-

dling the drive and drive application in Before you begin... to

offering troubleshooting suggestions and technical support infor-

mation. The topics discussed are:

•Handling your drive (see Before you begin...)

•Configuring the drive

•Attaching cables to the drive

•Mounting the drive

•Configuring the computer

•Troubleshooting

•Where to call for Seagate technical support

We hope your installation goes smoothly, but if complications

arise,alistof commonsymptomsandsolutionsisprovidedinthe

troubleshooting section. If the problem persists, contact your

dealerfirst.Yourdealerisfamiliarwith systemintegrationandthe

conflicts that arise. If you need additional help or information

about Seagate products, Seagate technicalsupport numbersare

provided.

Medalist 1080sl SCSI Installation Guide,August 1995 1

Drive features

Formatted Capacity (Mbytes) 1080.23

Total sectors 2,109,840

Cylinders 4,826

Physical heads 4

Sectors per track (average) 109

Bytes per sector 512

Spindle speed 5,376 RPM

Average seek time (msec) 12.5 msec

Cache (segmented) 128 Kbytes

Internal transfer rate (Mbits per second max) 33 MHz to

65 MHz

External transfer rate (Mbytes per second max)

Asynchronous

Synchronous 5.0

10.0

Power on to Ready 20 sec

Seek power (typical) 7.11W

Drive acoustics, Idle mode 30 dBA

2 Medalist 1080sl SCSI Installation Guide, August 1995

Read before you begin...

Note. Throughout this manual the Medalist 1080sl SCSI is

referred to by its model number, ST51080N.

Application. YourSeagate® drive is designed for IBM and IBM-

compatible personal computers, Macintosh and other systems

using the SCSI interface.

Turn off the system power before attempting any installation.

Static discharge. Observe the followingprecautions:

•Keep the drive in its static-shielded bag until you are ready to

complete theinstallation.Donotattach anycablestothedrive

while it is in its static-shielded bag.

•Handle the drive by its edges or frame, and do not touch the

I/O connector pins or the circuit board.

•Before handling any components, put on a grounded wrist

strap, or ground yourself frequently by touching the metal

chassis of a computer that is plugged into a grounded outlet.

•Use antistatic padding on all work surfaces.

•Avoid static-inducing carpeted areas.

Drive handling. The drive is extremely fragile—handle it with

care. Do not attach labels to any part of the drive.

Inspection. After you are familiar with the handling precautions

listed above, inspect the drive. If it appears to be damaged, call

your distributor or dealer immediately.

Warranty. See your authorized Seagate distributor or dealer.

Maintenance and repair. Seagate drives do notrequire mainte-

nance. The head/disc assembly is sealed; if you break the seal,

Medalist 1080sl SCSI Installation Guide,August 1995 3

you voidthe warranty. Seagate customer service centers are the

only facilitiesauthorized to repairSeagate drives. Seagate does

not sanction any third-party repair facilities.

Shipping. Keep your original box and packing materials for

transporting or shipping your drive. The box has a

Seagate

Approved Package

label. Shipping a drive in a nonapproved

container voids the warranty. Call your authorized Seagate dis-

tributor to purchase additional boxes.

Radio and television interference. This product complies with

ClassBlimitsforradionoiseemissionsfromcomputerequipment

as set out in the radio interference regulations of the Canadian

Department of Communications.

Le présent appareil numérique néémet pas de bruits radioélec-

triques depassant les limites applicable aux appareils numéri-

ques de Classe B prescrites dans le règlement sur le brouillage

radioélectrique edicté par le Ministère des Communications du

Canada.

Sicherheitsanleitung

1. Das Gerrät ist ein Einbaugerät, das für eine maximale Umge-

bungstemperatur von 55°C vorgesehen ist.

2. Zur Befestigung des Laufwerks werden 4 Schrauben 6-32

UNC-2Abenötigt.BeiseitlicherBefestigungdarfdiemaximale

Länge der Schrauben imChassis nicht mehr als 5,08 mm und

bei Befestigung an der Unterseite nicht mehr als 5,08 mm

betragen.

4 Medalist 1080sl SCSI Installation Guide, August 1995

3. Als Versorgungsspannugen werden benötigt:

+5V æ 5% 0,65A

+12V æ 5% 0,45A (1,9A fur ca. 10 Sek. fur æ 10%)

4. Die Versorgungsspannung mub SELV entsprechen.

5. Alle Arbeiten auf dem Festplatte dürfen nur von Ausgebilde-

tem Servicepersonal durchgeführt werden. Bitte schaffen Sie

Festplatteetiketten nicht weg.

6. Der Einbau des Drives mub den Anforderungen gemäb DIN

IEC 950V DC 0805/05.90 entsprechen.

Configuring the drive

Required materials:

2-mm jumper connector (supplied as spare jumpers)

Your Seagate drive is configured for operation using the options

jumper block (J8) shown in Figure 1 on page 6. The settings for

theavailableconfigurations areshowninFigure2onpage7.The

options jumper block (J8) allows you to:

•Set the SCSI ID

•Connect a remote LED

•Enable or disable parity

•Enable or disable the drive’s terminator

•Select the termination power source

SCSI ID settings. Each device on the SCSI bus must be as-

signed a unique SCSI ID. The drive uses pin-pairs1 and 2, 3 and

4, and 5 and 6 on the options jumperblock (J8) forassigning the

ID. The chart in Figure 2 shows you how to place the jumpers to

Medalist 1080sl SCSI Installation Guide, August 1995 5

J3. Standard

power connector

1234

J1. Interface

connector

J8. Options jumper block

+5V

+5V return

+12V return

+12V

Circuit

board

J1 pin 1

J8 pin 1

Figure 1. Connector and jumper block locations

6 Medalist 1080sl SCSI Installation Guide, August 1995

SCSI ID 0

SCSI ID 1

SCSI ID 2

SCSI ID 3 (default)

SCSI ID 4

SCSI ID 5

Note.

1. All other pins

are reserved. Do

not use them.

2. Jumpers on

pins 28 and 30

and 32 and 34

are spares; these

pins do not

require jumpers.

SCSI ID 6

SCSI ID 7

Remote LED 

connection

Reserved 

Do not use

Remote start

Enable parity (default)

Disable terminator

(default is enable)

Power to drive

terminator only

Power from bus, drive

terminator disabled

Power to drive

terminator and to

SCSI bus (default)

Power to SCSI

bus only

J8. Options jumper block Circuit board

side up.

11

9

7

5

3

13

1

15

17

19

21

33

31

29

27

25

23

Spares

Figure 2. Options jumper settings

Medalist 1080sl SCSI Installation Guide, August 1995 7

assign ID values0 through 7. Be sure that the ID you choose is

not used by another device on the SCSI bus.

YourSeagate driveis shippedby the factory configuredas SCSI

ID 3—jumpers are attached to pins 3 and 4 and pin 5 and 6. You

must reconfigure the SCSIID if another device is assigned SCSI

ID 3 or if you are making the drive the bootable drive. The

bootable drive must be Drive C. It must be assigned the ID

number your SCSIadapterrecognizes as the first positionon the

bus. Usually, this is SCSI ID 0 (refer to your SCSI host adapter

documentation).

If installing your new drive puts more than two drives on the bus,

your SCSI adapter may require thatyou install a device driver or

that you reconfigure its onboard BIOS. Refer to your SCSI

adapter’s user guide for instructions on how to install the third

drive.If a device driver isrequired, it will beprovided bythe SCSI

adapter manufacturer.

Remote LED. You can connect a remote LED to the drive using

pins 9 and 10 on jumper block J8. Connect the LED ground wire

(usually the black wire) to pin 9.

Remote start. This setting causes the drive to wait for a specific

commandfromthehostbeforeitstartsorstopsthespindlemotor.

Parityenable.Parityisamethodthatissometimesusedforerror

detection. The drive is shippedwith parity enabled.

Terminators. The drive is designed with single-ended drivers

andreceiversandmustbeusedwithotherSCSIdevicesthatuse

single-ended drivers and receivers. These systems require that

terminators be used at both ends of the SCSI bus to ensure the

integrity of the signal. The drive has built-in terminators that can

be enabled or disabled as required. It is shipped with the termi-

8 Medalist 1080sl SCSI Installation Guide, August 1995

Autres manuels pour MEDALIST 1080SL

Table des matières

Autres manuels Seagate Stockage

Seagate

Seagate ST3600002FC - Cheetah 600 GB Hard Drive Instructions d'utilisation et de sécurité

Seagate

Seagate ST9100828A - Momentus 5400.3 100 GB Hard... Manuel utilisateur

Seagate

Seagate U Series Manuel utilisateur

Seagate

Seagate BARRACUDA COMPUTE ST8000DMZ04 Manuel utilisateur

Seagate

Seagate ST425 Manuel utilisateur

Seagate

Seagate ST3450802SS Manuel utilisateur

Seagate

Seagate ST3100011A - 100GB UDMA/100 7200RPM 2MB IDE Hard... Manuel utilisateur

Seagate

Seagate ST330631A Manuel utilisateur

Seagate

Seagate Exos ST14000NM0001 Manuel utilisateur

Seagate

Seagate Expansion SSD Manuel utilisateur

Seagate

Seagate ST34501N Manuel utilisateur

Seagate

Seagate ST9160411AS - Momentus 7200.3 160 GB Hard... Instructions d'utilisation et de sécurité

Seagate

Seagate MEDALIST PRO ST36530N/W/WC Manuel utilisateur

Seagate

Seagate Medalist 2532 Manuel utilisateur

Seagate

Seagate Medalist Pro Family Manuel utilisateur

Seagate

Seagate ST150176LW Manuel utilisateur

Seagate

Seagate ST9100822A Manuel utilisateur

Seagate

Seagate GoFlex STBL500100 Manuel utilisateur

Seagate

Seagate ST3300657SS - Cheetah 300 GB Hard Drive Manuel utilisateur

Seagate

Seagate MARATHON 810 Manuel utilisateur

Seagate

Seagate CONSTELLATION ES ST32000444SS Manuel utilisateur

Seagate

Seagate Exos E 4U106 Manuel utilisateur

Seagate

Seagate Medalist 1720 Manuel utilisateur

Seagate

Seagate Barracuda Green Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur