Seagate Exos CORVAULT Manuel utilisateur

Exos® CORVAULT Quick Configuration Guide

Part Number 83-00007918-00-01, A • December 2021

Storage enclosure management

Select an interface that best fits your requirements to directly or remotely monitor and manage storage enclosure activity.

Method Description

Command-line interface (CLI)* Supports interactive and scripted commands

Storage Management Console (SMC)* Provides web-based GUI

JSON-based API Provides means to conduct JSON-based operations

Redfish/Swordfish-based API Provides means to conduct Redfish/Swordfish operations

XML-based Application Programming Interface (API) Provides means to conduct XML-based operations

*Access method discussed in the following content

Table 1 Interface options

TIP Use the QR code on the included Getting Started sheet to access related storage enclosure documentation online.

Command-line interface usage

One of the simplest methods of monitoring and managing activities performed by the storage enclosure system is to use the

command-line interface (CLI) embedded in each controller module. There are two primary access methods:

lDirect connection to a controller module's serial USB port using a terminal emulator installed on a management host

lRemote connection to a secure LANusing either SSH or HTTPS

Item Description

1 Manufacturing service port: Do not use

2 Serial USB port for use with supplied serial cable

3 Ethernet port for connection to management host

4 SAS data ports for data exchange

Figure 1 Ports on sample controller module

NOTE If the management host does not recognize the new controller or the connection, it cannot communicate with it.

All setup and configuration tasks identified in this section assume you have a direct connection between the management

host and the controller using the supplied or a known good serial cable. The connection you establish is an out-of-band

connection, since it does not use a data path to transfer information between the controller and the management host.

The host computer or server can be either Linux- or Windows-based. Certain operating systems require a special mode of

operation or the installation of a device driver.

Install a device driver

Some operating systems, such as a Windows OS that predates Windows 10/Server 2016, require download and installation of a

device driver before the OS recognizes the USB device and can connect to a controller module.

To install a device driver:

1. Navigate to https://www.seagate.com/support/systems/general-support/ and locate the device driver for download.

2. Download the zip file to the management computer.

3. Unzip the file, then click Setup.exe.

4. Follow all install instruction dialogs, clicking the prompts to run, accept, and install the device driver.

5. After successful completion of the install, close the dialog.

6. (Optional) Reset the management computer if required to complete installation and recognize the device driver.

Configure the management host for serial communication

After you successfully connect the supplied serial cable to the controller module, the management host should detect a new

USB device. The next step is to establish communication between the management host and the controller module.

Once you successfully install and run a supported terminal emulator, the controller presents a single serial port that uses the

related USB vendor identification (ID) and product ID hex codes.

Operating system Supported application

Microsoft Windows (all versions) HyperTerminal, TeraTerm, PuTTY

Linux (all versions) Minicom

Table 2 Supported terminal emulator applications

USB vendor identification code type Hex code

USB vendor identification code 0x210C

USB product identification code 0xA4A7

Table 3 Terminal emulator serial port hex codes

Configure Linux for serial communication

If you do not have a terminal emulator, such as Minicom, you must obtain one prior to completion of this task.

To configure Linux for serial communication:

IMPORTANT While Linux systems do not require installation of a device driver, it might require USB parameters as you

load the device driver to enable controller recognition.

modprobe usbserial vendor=0x210c product=0xa4a7 use_acm=1

You may also choose to incorporate the same information into the /etc/modules.conf file.

1. Determine if the operating system recognizes the USB (ACM) device by entering a command:

cat /proc/devices |grep -i "ttyACM"

If the OS discovers a device driver, it responds with the device number followed by ttyACM, for example:

116 ttyACM

2. To query the system about USB buses and the devices connected to them, use the list USB command:

lsusb

If the OSdiscovers a USB device driver, it responds with the single serial port, using the USB parameter hex codes:

ID 210c:a4a7

This confirms that the appropriate USB (ACM)device is visible to the management computer.

3. Invoke Minicom to configure it.

minicom -s

4. Select Serial Port Setup from the menu.

5. Select the parameter setting you want to change at the prompt by typing the related setting letter (A-G).

Setting Description Parameter settings

A Serial device /dev/ttyACM0

B Lockfile location /var/lock

C Callin program

D Callout program

E Bps/Par/Bits 11520 8N1

F Hardware flow control No

G Software flow control No

Table 4 Sample Linux Minicom serial port parameter settings

6. Press the ESC key to shift from the parameters to the configuration menu.

7. Select Save setup as dfl to save the parameter settings to default.

8. Select Exit from Minicom.

Configure Windows for serial communication

Use the terminal emulator to launch the device driver window and directly communicate with each controller module, after

meeting the following prerequisites:

lAn installed and tested terminal emulator.

lAn installed and tested Windows USB device driver to connect to the controller module USB port, by using the native

USBserial driver for Windows 10/Server 2016 or higher, or by downloading and installing the Seagate device driver.

To configure Windows for serial communication:

1. Start and configure the terminal emulator, using the specified settings.

Parameter Value Parameter Value

Connector COM3¹ Parity None

Baud rate 115,200 Stop bits 1

Data bits 8 Flow control None

¹ Your configuration determines the COM port used for USB connection. Verify you have the correct COM port.

Table 5 Terminal emulator port connection settings

2. In the terminal emulator, right-click on the connected and identified COM port and select Enable.

NOTE You must disable XON/XOFF when using Windows 10/Server 2016 with PuTTy so you can open the COMport.

3. For any hung connection, take the following corrective actions:

a. Validate the terminal emulator configuration is correct and you selected the correct COMport.

b. Quit the terminal emulator program.

c. In the Windows Device Manager window, right-click on the problem COM port and select Disable.

d. Confirm the COM port disabled status.

e. Right-click on COM port you just disabled and select Enable to re-enable it.

f. Start the terminal emulator program again and connect to the COM port, then validate the port settings again.

Connect to a controller module for configuration

When you first install a storage enclosure, you must perform some initial tasks to connect to and configure the system, such as

setting up a user, log in, and setting a valid IP address for each controller module (CM) serial COM port.

You have three options for setting up a network, each a viable approach to the same goal: connection to the CM.

lUse a direct connection to the serial COM port to access the Storage Management Console (SMC).

lUse a remotely connected network to access the SMC and connect to the CM through the identified factory default

IPaddresses.

lUse secure shell (SSH) to access the SMC at the identified factory default IP addresses.

> ssh 10.0.0.2

If the CM default IP address is not compatible with your network, you must manually set a valid IP address for each network

port, once you have a good serial port connection to the management host.

IP version Controller 0A addresses Controller 0B addresses

IPv4

IP address: 10.0.0.2 IP address: 10.0.0.3

IP subnet mask: 255.255.255.0 IP subnet mask: 255.255.255.0

Gateway IP address: 10.0.0.1 Gateway IP address: 10.0.0.1

IPv6

Autoconfig: Enabled Autoconfig: Enabled

Gateway: :: Gateway: ::

Link-Local Address: fe80::2c0:ffff:fe44:952f Link-Local Address: fe80::2c0:ffff:fe44:7010

Autoconfig IP: 6::2c0:ffff:fe44:952f Autoconfig IP: 6::2c0:ffff:fe44:7017

Table 6 Factory default network port IP addresses

To connect to a controller module for configuration:

1. Connect a serial cable from your management host to the CLI port on one of the CMs.

2. Launch the terminal emulator software and enable the CLI port for subsequent communication.

3. Press Enter to access the CLI prompt.

4. At the prompt, login with setup, press Enter, then press Enter again at the password prompt, for example:

System Version: S100R009

OS Version: SPM100R009-01

MC Version: SXM100R009-01

Serial Number: 00C0FF535A86

SEAGATE00C0FF527EB8B login: setup

Password:

5. For first time access to the SMC, enter Yat the prompt to continue.

6. To log in at the prompt, choose from one of the following actions:

a. For first time access, create a user, such as manage, and follow the on-screen directions to create a user account. After

doing so, the session will expire, and you can log in as the user you just created.

b. For all subsequent log in activity, log in using valid system user credentials.

7. At the prompt, type the following command to set the IP address for each controller module or both controller modules:

set network-parameters ip <address> netmask <netmask> gateway <gateway> controller a|b

where:

<address> is the IP address of the controller

<netmask> is the subnet mask

<gateway> is the IP address of the subnet router

a|b specifies the controller whose network parameters you are setting

For an ipV4 static example:

# set network-parameters ip 192.168.0.10 netmask 255.255.255.0 gateway 192.168.0.1

controller a

# set network-parameters ip 192.168.0.11 netmask 255.255.255.0 gateway 192.168.0.1

controller b

For a DHCP example:

# set network-parameters dhcp controller a

# set network-parameters dhcp controller b

NOTE See the CLI Reference Guide for information about IPv6, and the commands used to add IPv6 addresses and set

IPv6 network parameters. The ipv6 term is included within each relevant command name.

8. Choose one of the following actions to verify the new IP address:

a. For IPv4, use the show network-parameters command.

b. For IPv6, use the show ipv6-network-parameters command.

The result for each controller includes the IP address, subnet mask, and gateway address.

9. In the host computer's command window, first ping controller 0A and then controller 0B to verify connectivity.

ping <controller-IP-address>

10. When you are done using the CLI, exit the terminal emulator.

11. Retain the new IP addresses to access and manage the controllers by using either the SMC or the CLI.

If you cannot access your system after changing the IP address and waiting up to two or three minutes, your network

might require you to restart each affected Management Controller (MC) connected to the serial port. When you restart an

MC, you temporarily lose communication with the MC until it successfully returns to a ready state.

12. (Optional) To restart the management controller on both controllers, type the following command :

restart mc both

If you lose communication with the CLI while using an out-of-band cable connection, you can often restore communication by

disconnecting and reattaching the serial cable.

After you initially set a controller IP address and have a functioning connection, you can change it later using the SMC.

IMPORTANT Changing IP settings can cause management hosts to lose access to the storage enclosure.

Storage Management Console usage

Seagate provides a user-friendly interface that provides the means to configure, monitor, and manage the storage system: the

Storage Management Console (SMC). Access it through a supported browser, then use it to complete initial configuration of

the management host, then monitor and manage the storage enclosure.

Browser Version

Microsoft Internet Explorer 11

Mozilla Firefox 68 and newer

Google Chrome 70 and newer

Apple Safari (Mac) 11 and newer

Table 7 Supported browsers

For best results, use the following guidelines:

lEnable browser pop-up windows and set the browser to allow cookies for the related storage system IP addresses.

lFor Internet Explorer, set the browser’s local-intranet security option to medium or medium-low, and then add each

controller’s network IP address as a trusted site.

NOTE By default, your system is loaded with self-signed certificates. You should generate new self-signed certificates on

each controller, using the create certificate CLI command. Expect browser warnings about security or privacy concerns

related to self-signed or untrusted certificates or invalid certificate authorities. Bypass such warnings, if you are confident of a

secure connection. Depending on the browser and its settings, you can create a security exception to inhibit future related

warnings, despite the continued indication of an insecure connection in the browser address bar.

Access the web-based management interface

Once you successfully complete initial installation of the storage enclosure and initial configuration of the management host,

you can access the controller module's web-based management interface, the Storage Management Console (SMC). It is a

user-friendly interface that provides the means to configure, monitor, and manage the storage system.

To access the web-based management interface:

1. Launch a web browser on the computer connected to the controller module.

2. Enter the IP address of the controller module's network port, either the default address of 10.0.0.2/3 or the address you just

configured, then press Enter.

3. To log in to the SMC, perform the following actions:

a. In the web browser address field, type https://<controller-network-port-IP-address>,such as 10.1.4.33

without any leading zeros, and then press Enter. If a login prompt does not display, confirm you entered the correct IP

address.

b. At the prompt, enter the user name and password you just created. Refer to "Connect to a controller module for

configuration" on page4.

c. Select Log In. If the user authentication fails, a message indicates if the system is unavailable or unable to authenticate

the login.

4. Familiarize yourself with the SMC, consulting the online help topics or the Storage Management Guide.

5. To end your session, select Log Out from the banner, instead of simply closing the browser.

Complete the preboard and onboard process

During your initial connection, a wizard in the Storage Management Console (SMC) guides you through the first-time setup of

your system: the preboard and onboard process. Follow the on-screen directions to complete your setup.

To complete the preboard and onboard process:

1. Complete the following actions to successfully complete the preboard process:

a. Agree at the prompt to the end-user license agreement (EULA).

b. Create your profile username and password for all future access.

c. Update the controller firmware, as required.

2. Complete the following actions to successfully complete the onboard process:

a. Configure your system settings: network settings, data and time, user definitions, and system notifications.

b. Complete the storage system configuration, choosing the key features that pertain to the storage enclosure to ensure

your storage enclosure achieves optimal capacity and performance.

c. Provision the storage enclosure by creating hosts and host groups, then creating volumes and attaching them to hosts.

3. Continue to use the SMC to monitor and manage the storage enclosure by following instructions in the related Storage

Management Guide, or use the online help.

TIP Use the QR code on the included Getting Started sheet to access related storage enclosure documentation online.

Technology LLC in the United States and/or other countries. CORVAULT and Exos are either trademarks or registered trademarks of Seagate Technology LLC or

one of its affiliated companies in the United States and/or other countries. All other trademarks or registered trademarks are the property of their respective

owners. All coded instruction and program statements contained herein remain copyrighted works and confidential proprietary and trade secret information of

Seagate Technology LLC or its affiliates. Any use, derivation, disassembly, reverse engineering, dissemination, reproduction, or any attempt to modify, prepare

derivative works, reproduce, distribute, disclose copyrighted material of Seagate Technology LLC, for any reason, in any manner, medium, or form, in whole or in

part, if not expressly authorized, is strictly prohibited. Seagate reserves the right to change, without notice, product offerings or specifications.

Open source third-party licenses and code

Seagate storage products use open source software components. To view information about open source software licenses and open source code used in Seagate

storage products, see www.seagate.com/support.

Autres manuels pour Exos CORVAULT

Autres manuels Seagate Stockage

Seagate

Seagate ST902504EXA101-RK Manuel utilisateur

Seagate

Seagate 1AYBA4 Manuel

Seagate

Seagate GoFlex Satellite Manuel utilisateur

Seagate

Seagate ST31000322CS - Pipeline HD 1 TB Hard Drive Instructions d'utilisation et de sécurité

Seagate

Seagate Lyve Mobile Array Manuel utilisateur

Seagate

Seagate Personal Cloud SRN21C Manuel utilisateur

Seagate

Seagate SPINPOINT F3 HD164GJ Manuel utilisateur

Seagate

Seagate 1200 Manuel utilisateur

Seagate

Seagate Backup Plus Desktop Manuel utilisateur

Seagate

Seagate ST3120020A Manuel utilisateur

Seagate

Seagate ST1000VX000 Manuel utilisateur

Seagate

Seagate FIRECUDA ST2000DX002 Manuel utilisateur

Seagate

Seagate Barracuda 36FC Manuel utilisateur

Seagate

Seagate 600 SSD Manuel utilisateur

Seagate

Seagate 15K.3 - Cheetah - Hard Drive Manuel utilisateur

Seagate

Seagate Medalist 3240 Manuel utilisateur

Seagate

Seagate ST3600002FC - Cheetah 600 GB Hard Drive Manuel utilisateur

Seagate

Seagate Cheetah 15K.4 SAS ST3146854SS Manuel utilisateur

Seagate

Seagate IRONWOLF NAS ST14000VN0008 Manuel utilisateur

Seagate

Seagate Lyve Mobile Array Manuel utilisateur

Seagate

Seagate ST3144 Series Manuel utilisateur

Seagate

Seagate ST500VT001 Manuel utilisateur

Seagate

Seagate MARATHON 1680 Manuel utilisateur

Seagate

Seagate Joy Drive Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur