SEA Sprint Manuel utilisateur

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

SPRINT

SEA S.p.A.

Zona Ind.le S. Atto - 64020 S. Nicolò a Tordino (TE)

Tel. 0861.588341 - Fax 0861.588344

Numero Verde: 800.979.732

www.seateam.com

e-mail: [email protected]

Italiano

English

Français

Español

Rev. 01 - 03/2016

Barriera oleodinamica

H barrierydraulic

Barrière oleodynamique

Barrera oleodinámica

67411055-A 1

SPRINT BARRIER

INSTALLATION MANUAL Thank you for choosing a SEA product. This choice will give you

the opportunity to understand that our company aims at

combining high-tech and remarkable reliability and safety, thanks

to studies, research and the accurate analysis of our customers'

needs, without undermining the simple use and installation of our

products.

General features

SPRINT is a barrier (2, 3, 4, 5 m) recommended for the hydraulic

automation of access points which require a high opening/closing

speed (parking lots, motorways, airports, etc.) and frequent use

features. The automation includes an anti-crush security system

with adjustable sensitivity, which guarantees a barrier force value

not exceeding 15 kg, thus protecting people and objects from any

accidents. A highly reliable slowdown device guarantees the total

control of the forces of inertia.

The emergency batteries guaranty at least 15 opening cycles

(depending on the installed accessories) in case of power failure

and a release system allows the manual opening in case of

emergency.

English

The automation system is composed of the following elements:

1 Adjustable mechanical and electronic stop with microswitch (where present)

2 Manual release with key

3 Galvanised steel rocker arm.

4 SPRINT, casing cover with lock and DIN key

5 Balancing spring.

6 Electronic control unit, a complex device which can be used to program and manage all the

operation and safety systems.

7 Foundation plate out of galvanized steel

8 24V - 1400 rpm electric motor

9 Cataphoresis-treated and polyester painted SPRINT casing, for outside, protects all included

mechanical and electronic devices from fire, flood, lightning, etc.

Predisposed for the application of photocells, key switch, proximity reader.

Stainless steel casing available on request.

Main components:

1) Adjustable mechanical and electronic stops

2) Release screw

3) Rocker arm

4) SPRINT casing cover

5) Balancing spring

6) Electronic control unit

7) SPRINT anchoring plate (optional)

8) Piston

9) Hydraulic unit

10) SPRINT casing

Sistemi Elettronici

di Apertura Porte e Cancelli

INSTALLATION INSTRUCTIONS

1) Spring position

Thanks to its high flexibility, the barrier you are installing can be closed on the

right-hand or left-hand side of the post, according to your needs.

e.g. if the spring is on the right-hand side, the guard opens on the right (see Fig. 2).

English

Fig.2

Fig.1

Opening on the left Opening on the right

Overall dimensions:

Light beam

Beam Length

D. Spring Cod. kit beam

2 5,5 16400005

2,5 6 16400008

3 6 16400008

3,5 7 16400015

4 7 16400015

4,5 8 16400026

5 8 16400026

24V Version 24V Version 230V (1L) Version 230V (2L) Version Fast Version

230 V ± 5% - 50/60 Hz~

24V

10 A

45 W

IP55

90%

User 1 24V DG R1

-20° + 55°C

2 L

230V

1,1 A

220W

1430 rpm

10”

75%

6,3 µF

Gate 1 DG R1

130°

1 L

51 kg

115 V ± 5% - 50/60 Hz~

230 V ± 5% - 50/60 Hz~

1,2 A

250W

3”

3 m

12,5 µF

3 L

1,0 A

270W

8”

2 L

Technical features

Supply voltage

supply voltage Hydraulic unit

Absorbed power

Motor power

Motor speed

Working temperature

Opening/closing time

Protection class

Manual release system

Usage frequency

Anti-crushing device

Holding block

Slowdown

Barrier body treatment

Max. Length

Thermal protection intervention

Starting capacitor

Pump capacity

Weight

Electronic equipment

Note: The frequency of use is valid only for the first hour at 20°C room temperature.

Adjustable

A By pass valve mmeter

Yes

Electronic

Cataphoresis treated and polyester painted

5 m

Beam 3 m

Beam 4 m

Beam 5 m

6’’

8’’

10’’

Speed 100%

Speed 80%

Speed 70%

SPEED BEAMS (For SPRINT 24V only)

Beam Length Opening time

Speed setting

142,5

830

1003

310 164

Sistemi Elettronici

di Apertura Porte e Cancelli

Articulated beam

3,5 m 10’’ Speed 70%

2) Foundation plate anchoring

-Make a 500 x 500 x 300 mm (depth) hole in the ground.

-Fill the hole with R425 concrete and place the foundation plate as shown in

Fig. 3.

-Accurately level the plate.

* The middle hole of the plate must be used for cable routing. Therefore, make

sure that the conduit connected to the hole complies with current regulations,

before filling the hole with concrete.

Anchoring

nuts and

washers

Hole for the conduit

containing the

electrical cables

3) Post anchoring on the foundation plate

-Place the casing so that the holes on the base match the

screws located on the foundation plate.

-Make sure that the conduit for the cables goes through the large

hole of the casing base.

-Fix the casing on the foundation plate, screwing the supplied

nuts and washers carefully.

English

Fig.3

500

300

Concrete

Foundation plate

to be levelled

Ground anchor

Conduit

Fig.4

Fig.6

Sistemi Elettronici

di Apertura Porte e Cancelli

30 mm

Fig.5

English

4) Mounting of the spring

N.B.: The operator comes as shown in Fig.1 (opening on the left).

Example:

Barrier with opening on the left (Fig.1)

Barrier with opening on the right (Fig. 2)

Before installing the spring check the choice of the barrier, if right or left hand side.

If the barrier is with opening on the right, move the piston from the right to the left hand side as shown in Fig.7 and 9, by rotating the

piston about 360°on itself (Fig.8).

N.B.: Before executing this operation release the motor-reducer as shown in Fig.21.

Note: Before reversing the piston, release about a half turn, the two fittings of the connection pipes between the hydraulic unit

and the hydraulic piston to facilitate the inversion (only on the unit) as shown in Fig.7, being careful not to cause narrowings on

hoses (not visible in the figures).

Once exchanged the piston tighten its fixation screw and lubricate with grease (Use DIN 51502 KP 2 N-20 - K 2 K-20 grease).

Lubrication

with grease

during mounting

Insert the spring in to the carter as shown in Fig.10.

360°

Fig.7 Fig.8 Fig.9

Fig.10

Sistemi Elettronici

di Apertura Porte e Cancelli

5) Mounting of the Light beam

Note: For 4 and 5 m beams it is recommended to use the fork support or the flexible support.

English

Fig. 11

5 mm

Fig. 11-a

Mount the first segment (A) of the LED profile, positioning it in doorstop on the fixing, mount the joint, fit the second segment (B) of

the LED profile and repeat the operation for all segments of the LED profile up to covering the length of the whole beam. The last

profile LED must be cut with a hacksaw at the end of the rod (Fig.11-a). Intersperse each segment of the LED profile with a joint.

Mount the anti-blunt rubber so that it comes out from the beam about 5mm (Fig.11-a).

Fixing

Led profile

(A)

Joint

Led profile

(B)

Anti-blunt rubber

Sistemi Elettronici

di Apertura Porte e Cancelli

Fig.12

6) Skirt mounting on the beam English

Sistemi Elettronici

di Apertura Porte e Cancelli

7) Beam balancing

-Release the beam with manual release, so that it is

free to be opened and closed manually (Fig.13).

-Place the beam at approx. 45°.

-Loosen or tighten the spring stretching nut until the

spring counterbalances the weight of the 45° beam

(Fig. 13). The best balancing position is obtained

when the beam reaches the position shown in Fig.

13.

-After having obtained the balancing, lock the nuts of

the spring stretcher with the counter nut and re-

block the motor.

Note: For the correct balancing of the beam, we

recommend to unhook the piston from the equalizer

by removing the pivot as in Figure 7.

Spring stretching nut

Anchoring

lock nut

8) Beam levelling

Note: this operation must be carried out only if the beam is not

perfectly horizontal (closing stage) or vertical (opening stage) at the

end of its stroke.

-Release the beam with the special manual release so that it is

free to open and close manually.

-Release the screws of the limit switch on unscrewing the nuts

on the mechanical stops (fig.14).

-Loosen or tighten the stop screws so that the beam is released

in its vertical position (opening stage) and horizontal position

(closing stage) (Fig. 14).

-After having executed the levelling lock the screws of the limit

switch tightening the nuts on the mechanical stops and re-lock

the beam.

Rocker

arm

English

Fig. 13

45°

Fig. 14

Sistemi Elettronici

di Apertura Porte e Cancelli

ONLY 230V VERSION

Remove the vent screw (Fig. 16).

Vent screw

English

9) Force adjustment

If necessary the piston force can be adjusted by the two

adjusting screws (grey and yellow) placed on the front lower

place of the Hydraulic pump unit (Fig. 15).

* The automation is adjusted at 15 Kg force ex works so to

guarantee the anti-crush safety. We recommend to adjust it only

in case of necessity.

Replace the red cap with the supplied black one.

ONLY 24V VERSION

Pressure adjusting

valves

(Only for 230V-115V version)

Fig. 15

Red transportation

cap

(Only for

230V-115V version)

-+-+

Fig.16

Sistemi Elettronici

di Apertura Porte e Cancelli

English

When mounting the

beam as shown in the

figure use hole A.

When mounting the

beam as shown in the

figure use hole B.

Use hole A for assembly of the right beam.

Use hole B for assembly of the left beam.

10) Drilling scheme for passage of light power cable

Fig.19

Fig.17

A B

150

Fig.18

Left beam Right beam

Sistemi Elettronici

di Apertura Porte e Cancelli

Autres manuels pour Sprint

Table des matières

Manuels Autre populaires d'autres marques

GO Industries

GO Industries 38017 Manuel utilisateur

Cissell

Cissell 30LBCMAN2 Manuel utilisateur

RIDGID

RIDGID K-60SP Manuel utilisateur

Gage Bilt

Gage Bilt GB751SH-5 Manuel utilisateur

OVE

OVE SIERRA 60 Manuel utilisateur

ReelCraft

ReelCraft 7800 OLB21 Manuel utilisateur

Body Armor 4x4

Body Armor 4x4 ECO-SERIES Manuel utilisateur

ROBLIN

ROBLIN DROP Guide de l'utilisateur

EMG

EMG EMG-ACB BARREL Manuel de service

MiniSolar

MiniSolar MT-150 Manuel utilisateur

Parkside

Parkside PSZ 250 B2 Manuel utilisateur

ABB

ABB REM 610 Manuel du produit

Parkside

Parkside 55992 Manuel du propriétaire

Skyjacker

Skyjacker F250 Manuel utilisateur

IBM

IBM IBM SYSTEM Z Guide d'installation

Grech Motors

Grech Motors G28 Manuel utilisateur

NOVAK

NOVAK BATTERY CARE SHEET Mode d’emploi

Telemotive

Telemotive blue PiraT Mini Guide de l'utilisateur