SCS CTE701 Manuel utilisateur

Employee Owned

SCS - 926 JR Industrial Drive, Sanford, NC 27332

East: (919) 718-0000 | West: (909) 627-9634 • Website: StaticControl.com

CTE701 Verication Tester

Operation Instructions

Description

The SCS CTE701 Verification Tester is used to perform

periodic test limit verification of the SCS WS Aware

Monitor, Ground Master Monitor, Iron Man® Plus

Monitor, and Ground Man Plus Monitor. Verification

may be accomplished without removing the monitor

from its workstation. The Verification Tester is National

Institute of Standards and Technology (NIST) traceable.

Frequency of verification is based on the critical

nature of the ESD susceptible items handled. SCS

recommends annual calibration of workstation monitors

and the CTE701 Verification Tester. The CTE701

Verification Tester meets ANSI/ESD S20.20 and

Compliance Verification ESD TR53.

November 2022

The SCS CTE701 Verification Tester can be used with

the following items:

Item Description

770067 WS Aware Monitor

770068 WS Aware Monitor

CTC061-3-242-WW WS Aware Monitor

CTC061-RT-242-WW WS Aware Monitor

CTC062-RT-242-WW WS Aware Monitor

770044 Ground Master Monitor

CTC331-WW Iron Man® Plus Monitor

CTC334-WW Ground Man Plus Monitor

CTC337-WW Wrist Strap and Ground Monitor

773 Wrist Strap and Ground Monitor

Packaging

1 CTE701 Verification Tester

1 Black Alligator-to-Banana Test Lead, 3 ft.

1 Red Mini Grabber-to-Banana Test Lead, 3 ft.

1 Black 3.5 mm Mono Cable, 2 ft.

1 9V Alkaline Battery

1 Certificate of Calibration

Made in the

United States of America

USER GUIDE TB-9031

Figure 1. SCS CTE701 Verication Tester

Employee Owned

SCS - 926 JR Industrial Drive, Sanford, NC 27332

East: (919) 718-0000 | West: (909) 627-9634 • Website: StaticControl.com

Features and Components A. Operator Dual-wire Jack: Connect one end of the

included 3.5 mm mono cable here, and the other end

into the monitor's operator jack.

B. Soft/Metal Ground Banana Jack: Connect the

banana plug terminal of the red test lead here, and the

other end to the monitor's mat or tool ground circuit.

C. Reference Ground Banana Jack: Connect the

banana plug terminal of the black test lead here, and

the other end to equipment ground.

D. High Body Voltage Test Switch: Simulates a

BODY VOLTAGE FAIL condition on the monitor's

operator circuit when pressed.

E. Low Body Voltage Low Test Switch: Simulates

a BODY VOLTAGE PASS condition on the monitor's

operator circuit when pressed.

F. Soft Ground Test Switch: Simulates a MAT PASS

condition on the monitor when pressed.

G. Wrist Strap Test Switch: Simulates a OPERATOR

PASS condition on the monitor when pressed.

H. Test Limit DIP Switch: Configures the test limits on

the CTE701 Verification Tester.

I. High Metal Ground Test Switch: Simulates a TOOL

FAIL condition on the monitor when pressed.

J. High EMI Test Switch: Simulates an EMI FAIL

condition on the monitor's tool circuit when pressed.

K. Low EMI Test Switch: Simulates an EMI PASS

condition on the monitor's tool circuit when pressed.

L. Low Metal Ground Test Switch: Simulates a TOOL

PASS condition on the monitor when pressed.

M. Low Battery LED: Illuminates when the battery

needs to be replaced.

N. Power LED: Illuminates when the CTE701

Verification Tester is powered.

O. Power Switch: Slide to the left to power the

Verification Tester OFF. Slide to the right to power the

Verification Tester ON.

Figure 2. CTE701 Verication Tester features and

components

A B C

Employee Owned

SCS - 926 JR Industrial Drive, Sanford, NC 27332

East: (919) 718-0000 | West: (909) 627-9634 • Website: StaticControl.com

Installation

The CTE701 Verification Tester's 10-position DIP switch

is used to configure its test limits for soft ground, metal

ground, EMI, and operator.

Soft Ground

The soft ground resistance is configured with switches

1-4. Pressing the SOFT GROUND pushbutton will result

in a load with slightly lower resistance than the test limit.

Switch

Test Limit 1234

1 gigohm OFF OFF OFF ON

400 megohms OFF OFF ON ON

100 megohms OFF ON ON ON

10 megohms ON ON ON ON

Metal Ground

The metal ground impedance is configured with

switches 5-8. Pressing the HIGH METAL GROUND

pushbutton will load 1 ohm higher than the configured

test limit. Pressing the PASS METAL GROUND

pushbutton will load 1 ohm less than the test limit. For

example, if the monitor to be checked is set to 10 ohms,

the Verification Tester will verify that it passes at 9 ohms

and fails at 11 ohms.

Switch

Test Limit 5678

1 ohm ON ON ON ON

2 ohms OFF ON ON ON

3 ohms ON OFF ON ON

4 ohms OFF OFF ON ON

5 ohms ON ON OFF ON

6 ohms OFF ON OFF ON

7 ohms ON OFF OFF ON

8 ohms OFF OFF OFF ON

9 ohms ON ON ON OFF

10 ohms OFF ON ON OFF

11 ohms ON OFF ON OFF

12 ohms OFF OFF ON OFF

13 ohms ON ON OFF OFF

14 ohms OFF ON OFF OFF

15 ohms ON OFF OFF OFF

16 ohms OFF OFF OFF OFF

EMI

The EMI high frequency signal is configured with switch

9. The CTE701 Verification Tester provides two different

levels of high frequency signal: elevated and normal.

Pressing the HIGH EMI pushbutton will load a high

signal level within its range. Pressing the LOW EMI

pushbutton will load a low signal within its range.

Switch

Signal Level 9

Elevated ON

Normal OFF

Wrist Strap

The wrist strap resistance is configured with switch 10.

The CTE701 Verification Tester provides resistance

of a certain value across the wrist strap terminal

input in order to simulate a wrist strap. A good quality

dual-wire wrist cord has a 1 megohm resistor in each

of its conductors. The Verification Tester is designed

to simulate dual-wire wrist straps with and without

resistors. The 12 megohms setting simulates a wrist

strap with two 1 megohm resistors in series.

Switch

Test Limit 10

12 megohms OFF

10 megohms ON

Operation

Iron Man® Plus Workstation Monitor

CONFIGURING THE VERIFICATION TESTER

Configure the Verification Tester's DIP switch to the

settings shown below. This will make its test limits

match the factory default limits of the monitor.

VERIFYING THE OPERATOR CIRCUIT

1. Use the black test lead to connect the Verification

Tester to equipment ground.

2. Power the Verification Tester ON.

3. Use the 3.5 mm mono cable to connect the

Verification Tester to the monitor's operator jack.

The monitor's operator LED will illuminate red, and

its alarm will sound.

Employee Owned

SCS - 926 JR Industrial Drive, Sanford, NC 27332

East: (919) 718-0000 | West: (909) 627-9634 • Website: StaticControl.com

4. Press and hold the Verification Tester's WRIST

STRAP test switch. The monitor's operator LED will

illuminate green, and its audible alarm will stop. This

verifies the operator circuit's impedance limit.

Figure 3. Connecting the Verication Tester to the Iron

Man® Plus Workstation Monitor's operator jack

Figure 4. Pressing the WRIST STRAP test switch

5. Continue to press and hold the Verification Tester's

WRIST STRAP test switch. Simultaneously, press

and hold the Verification Tester's LOW BODY

VOLTAGE test switch. The monitor's operator LED

will remain green, and no audible alarm will sound.

This verifies the operator circuit's low body voltage

limit.

Figure 5. Pressing the WRIST STRAP and LOW BODY

VOLTAGE test switches simultaneously

6. Continue to press and hold the Verification Tester's

WRIST STRAP test switch. Simultaneously, press

and hold the Verification Tester's HIGH BODY

VOLTAGE test switch. The monitor's green operator

LED will illuminate continuously, its red LED will

blink, and an audible alarm will sound. This verifies

the operator circuit's high body voltage limit.

Figure 6. Pressing the WRIST STRAP and HIGH BODY

VOLTAGE test switches simultaneously

7. Disconnect the mono cable from the monitor.

VERIFYING THE MAT CIRCUIT

8. Connect the red test lead to red banana jack located

at the top of the Verification Tester.

9. Disconnect the monitor's white mat monitor cord

from its worksurface mat and turn it over to expose

its 10 mm snap.

10. Clip the red test lead's mini grabber to the 10 mm

snap on the white mat monitor cord.

Figure 7. Connecting the Verication Tester to the Iron

Man® Plus Workstation Monitor's mat monitor cord

Monitor's

Mat Monitor Cord

11. Wait approximately 5 seconds for the monitor's mat

LED to illuminate red and sound its audible alarm.

Employee Owned

SCS - 926 JR Industrial Drive, Sanford, NC 27332

East: (919) 718-0000 | West: (909) 627-9634 • Website: StaticControl.com

12. Press and hold the Verification Tester's SOFT

GROUND test switch. The monitor's mat LED will

illuminate green, and its audible alarm will stop

after approximately 3 seconds. This verifies the mat

circuit's resistance limit.

Figure 8. Pressing the SOFT GROUND test switch

13. Disconnect the red test lead from the monitor's

white mat monitor cord.

14. Reinstall the white mat monitor cord to the

worksurface mat.

VERIFYING THE IRON CIRCUIT

Note: A variable DC power supply must be used to

complete this procedure. The CTE701 Verification

Tester cannot verify the iron circuit in the Iron Man®

Plus Workstation Monitor.

15. Turn the voltage alarm trimpot at the back of the

monitor fully clockwise. This configures it to ±5 V.

16. Power the variable DC power supply. Configure it to

5.0 V.

17. Connect the negative terminal from the variable

DC power supply to ground. Connect its positive

terminal to the yellow alligator cord connected to the

monitor's BOARD terminal. The monitor's Iron LED

should illuminate red and its audible alarm should

sound.

18. Set the variable DC power supply to 4.0 V. The

monitor's Iron LED should illuminate green and its

audible alarm should stop.

19. Disconnect the variable DC power supply from the

monitor and ground. Connect its positive terminal

to ground and its negative terminal to the monitor's

yellow alligator cord.

20. Verify that the variable DC power supply is still set

to 4.0 V. The monitor's Iron LED should illuminate

green.

21. Set the variable DC power supply to 5.0 V. The

monitor's Iron LED should illuminate red and its

audible alarm should sound.

WS Aware Monitor

CONFIGURING THE VERIFICATION TESTER

Configure the Verification Tester's DIP switch to the

settings shown below. This will make its test limits

match the factory default limits of the monitor.

VERIFYING THE OPERATOR CIRCUIT

1. Use the black test lead to connect the Verification

Tester to equipment ground.

2. Power the Verification Tester ON.

3. Use the 3.5 mm mono cable to connect the

Verification Tester to the monitor's operator jack.

The monitor's operator LED will illuminate red, and

its alarm will sound.

Figure 9. Connecting the Verication Tester to the WS

Aware Monitor's operator jack

4. Press and hold the Verification Tester's WRIST

STRAP test switch. The monitor's operator LED will

illuminate green, and its audible alarm will stop. This

verifies the operator circuit's impedance limit.

Figure 10. Pressing the WRIST STRAP test switch

Employee Owned

SCS - 926 JR Industrial Drive, Sanford, NC 27332

East: (919) 718-0000 | West: (909) 627-9634 • Website: StaticControl.com

5. Continue to press and hold the Verification Tester's

WRIST STRAP test switch. Simultaneously, press

and hold the Verification Tester's LOW BODY

VOLTAGE test switch. The monitor's operator LED

will remain green, and no audible alarm will sound.

This verifies the operator circuit's low body voltage

limit.

Figure 11. Pressing the WRIST STRAP and LOW BODY

VOLTAGE test switches simultaneously

6. Continue to press and hold the Verification Tester's

WRIST STRAP test switch. Simultaneously, press

and hold the Verification Tester's HIGH BODY

VOLTAGE test switch. The monitor's green operator

LED will illuminate continuously, its red LED will

blink. This verifies the operator circuit's high body

voltage limit.

Figure 12. Pressing the WRIST STRAP and HIGH BODY

VOLTAGE test switches simultaneously

7. Disconnect the mono cable from the monitor.

VERIFYING THE MAT CIRCUIT

8. Connect the red test lead to red banana jack located

at the top of the Verification Tester.

9. Disconnect the monitor's white mat monitor cord

from its worksurface mat and turn it over to expose

its 10 mm snap.

10. Clip the red test lead's mini grabber to the 10 mm

snap on the white mat monitor cord.

11. Wait approximately 5 seconds for the monitor's mat

LED to illuminate red and sound its audible alarm.

12. Press and hold the Verification Tester's SOFT

GROUND test switch. The monitor's mat LED will

illuminate green, and its audible alarm will stop

after approximately 3 seconds. This verifies the mat

circuit's resistance limit.

Figure 13. Connecting the Verication Tester to WS

Aware Monitor's mat monitor cord

Monitor's

Mat Monitor Cord

Figure 14. Pressing the SOFT GROUND test switch

13. Disconnect the red test lead from the monitor's

white mat monitor cord.

14. Reinstall the white mat monitor cord to the

worksurface mat.

Employee Owned

SCS - 926 JR Industrial Drive, Sanford, NC 27332

East: (919) 718-0000 | West: (909) 627-9634 • Website: StaticControl.com

VERIFYING THE TOOL CIRCUIT

15. Disconnect the monitor's tool cord from its metal

tool.

16. Clip the red test lead's mini grabber to the tool cord.

Figure 15. Connecting the Verication Tester to WS

Aware Monitor's tool cord

Monitor's

Tool Cord

17. Wait for the monitor's tool LED to illuminate red and

sound its audible alarm.

18. Press and hold the Verification Tester's METAL

GROUND PASS test switch. The monitor's tool LED

will illuminate green, and its audible alarm will stop.

This verifies the tool circuit's impedance limit.

Figure 16. Pressing the METAL GROUND PASS test

switch

19. Press and hold the Verification Tester's METAL

GROUND FAIL test switch. The monitor's tool LED

will illuminate red, and its audible alarm will sound.

This verifies the tool circuit's impedance limit.

20. Press and hold the Verification Tester's METAL

GROUND PASS test switch. Simultaneously, press

and hold the Verification Tester's EMI LOW test

switch. The monitor's tool LED will remain green,

and no audible alarm will sound. This verifies the

operator circuit's low EMI voltage limit.

Figure 17. Pressing the METAL GROUND FAIL test

switch

Figure 18. Pressing the METAL GROUND PASS and

EMI LOW test switches simultaneously

21. Press and hold the Verification Tester's METAL

GROUND PASS test switch. Simultaneously, press

and hold the Verification Tester's EMI HIGH test

switch. The monitor's tool LED will blink red, and its

audible alarm will sound. This verifies the operator

circuit's high EMI voltage limit.

Figure 19. Pressing the METAL GROUND PASS and

EMI HIGH test switches simultaneously

22. Disconnect the red test lead from the monitor's tool

cord.

23. Reinstall the tool cord to the metal tool.

Employee Owned

SCS - 926 JR Industrial Drive, Sanford, NC 27332

East: (919) 718-0000 | West: (909) 627-9634 • Website: StaticControl.com

Ground Master Monitor

CONFIGURING THE VERIFICATION TESTER

Configure the Verification Tester's DIP switch to the

settings shown below. This will make its test limits

match the factory default limits of the monitor.

VERIFYING THE TOOL CIRCUIT

1. Disconnect the monitor's tool cord from its metal

tool.

2. Clip the red test lead's mini grabber to the tool cord.

Figure 20. Connecting the Verication Tester to Ground

Master Monitor's tool cord

Monitor's

Tool Cord

3. Wait for the monitor's tool LED to illuminate red and

sound its audible alarm.

4. Press and hold the Verification Tester's METAL

GROUND PASS test switch. The monitor's tool LED

will illuminate green, and its audible alarm will stop.

This verifies the tool circuit's impedance limit.

Figure 21. Pressing the METAL GROUND PASS test

switch

5. Press and hold the Verification Tester's METAL

GROUND FAIL test switch. The monitor's tool LED

will illuminate red, and its audible alarm will sound.

This verifies the tool circuit's impedance limit.

Figure 22. Pressing the METAL GROUND FAIL test

switch

6. Press and hold the Verification Tester's METAL

GROUND PASS test switch. Simultaneously, press

and hold the Verification Tester's EMI LOW test

switch. The monitor's tool LED will remain green,

and no audible alarm will sound. This verifies the

operator circuit's low EMI voltage limit.

Figure 23. Pressing the METAL GROUND PASS and

EMI LOW test switches simultaneously

7. Press and hold the Verification Tester's METAL

GROUND PASS test switch. Simultaneously, press

and hold the Verification Tester's EMI HIGH test

switch. The monitor's tool LED will blink red, and its

audible alarm will sound. This verifies the operator

circuit's high EMI voltage limit.

Figure 24. Pressing the METAL GROUND PASS and

EMI HIGH test switches simultaneously

Employee Owned

SCS - 926 JR Industrial Drive, Sanford, NC 27332

East: (919) 718-0000 | West: (909) 627-9634 • Website: StaticControl.com

8. Disconnect the red test lead from the monitor's tool

cord.

9. Reinstall the tool cord to the metal tool.

Ground Man Plus Workstation Monitor

CONFIGURING THE VERIFICATION TESTER

Configure the Verification Tester's DIP switch to the

settings shown below. This will make its test limits

match the factory default limits of the monitor.

VERIFYING THE OPERATOR CIRCUIT

1. Use the black test lead to connect the Verification

Tester to equipment ground.

2. Power the Verification Tester ON.

3. Use the 3.5 mm mono cable to connect the

Verification Tester to the monitor's operator jack.

The monitor's operator LED will illuminate red, and

its alarm will sound.

Figure 28. Pressing the WRIST STRAP and HIGH BODY

VOLTAGE test switches simultaneously

Figure 25. Connecting the Verication Tester to the

Ground Man Plus Workstation Monitor's operator jack

Figure 26. Pressing the WRIST STRAP test switch

Figure 27. Pressing the WRIST STRAP and LOW BODY

VOLTAGE test switches simultaneously

4. Press and hold the Verification Tester's WRIST

STRAP test switch. The monitor's operator LED will

illuminate green, and its audible alarm will stop. This

verifies the operator circuit's impedance limit.

5. Continue to press and hold the Verification Tester's

WRIST STRAP test switch. Simultaneously, press

and hold the Verification Tester's LOW BODY

VOLTAGE test switch. The monitor's operator LED

will remain green, and no audible alarm will sound.

This verifies the operator circuit's low body voltage

limit.

6. Continue to press and hold the Verification Tester's

WRIST STRAP test switch. Simultaneously, press

and hold the Verification Tester's HIGH BODY

VOLTAGE test switch. The monitor's green operator

LED will illuminate continuously, its red LED will

blink, and an audible alarm will sound. This verifies

the operator circuit's high body voltage limit.

7. Disconnect the mono cable from the monitor.

Employee Owned

SCS - 926 JR Industrial Drive, Sanford, NC 27332

East: (919) 718-0000 | West: (909) 627-9634 • Website: StaticControl.com

VERIFYING THE TOOL CIRCUIT

8. Disconnect the monitor's tool cord from its metal

tool.

9. Clip the red test lead's mini grabber to the tool cord.

Figure 29. Connecting the Verication Tester to Ground

Man Plus Monitor's tool cord

Monitor's

Tool Cord

Figure 30. Pressing the METAL GROUND PASS test

switch

Figure 31. Pressing the METAL GROUND FAIL test

switch

Figure 32. Pressing the METAL GROUND PASS and

EMI LOW test switches simultaneously

Figure 33. Pressing the METAL GROUND PASS and

EMI HIGH test switches simultaneously

10. Wait for the monitor's tool LED to illuminate red and

sound its audible alarm.

11. Press and hold the Verification Tester's METAL

GROUND PASS test switch. The monitor's tool LED

will illuminate green, and its audible alarm will stop.

This verifies the tool circuit's impedance limit.

12. Press and hold the Verification Tester's METAL

GROUND FAIL test switch. The monitor's tool LED

will illuminate red, and its audible alarm will sound.

This verifies the tool circuit's impedance limit.

13. Press and hold the Verification Tester's METAL

GROUND PASS test switch. Simultaneously, press

and hold the Verification Tester's EMI LOW test

switch. The monitor's tool LED will remain green,

and no audible alarm will sound. This verifies the

operator circuit's low EMI voltage limit.

14. Press and hold the Verification Tester's METAL

GROUND PASS test switch. Simultaneously, press

and hold the Verification Tester's EMI HIGH test

switch. The monitor's tool LED will blink red, and its

audible alarm will sound. This verifies the operator

circuit's high EMI voltage limit.

15. Disconnect the red test lead from the monitor's tool

cord.

16. Reinstall the tool cord to the metal tool.

Table des matières

Autres manuels SCS Instrument de mesure

SCS

SCS CTC034-030-3-WW Document technique

SCS

SCS Static Monitor 790 Instructions d'installation et d'utilisation

SCS

SCS 770048 Manuel du propriétaire

SCS

SCS CTC337 Instructions d'installation et d'utilisation

SCS

SCS CTC334-T Manuel utilisateur

SCS

SCS WS aware Manuel utilisateur

SCS

SCS 770063 Instructions d'installation et d'utilisation

SCS

SCS 770066 Instructions d'installation et d'utilisation

SCS

SCS 770760 Instructions d'installation et d'utilisation

SCS

SCS CTM051 Manuel utilisateur

SCS

SCS SRMETER2 Document technique

SCS

SCS TB-9017 Manuel utilisateur

SCS

SCS CTM048 Manuel utilisateur

SCS

SCS CTM048-21 EM Eye Manuel utilisateur

SCS

SCS 740 Manuel utilisateur

SCS

SCS 711 Manuel utilisateur

SCS

SCS 711RS Manuel utilisateur

SCS

SCS CTS001 Instructions d'installation et d'utilisation

SCS

SCS WSMONITOR1 Manuel utilisateur

SCS

SCS 701 Guide d'installation

SCS

SCS TB-9079 Manuel utilisateur

SCS

SCS 770066 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur