Screen Innovations ZERO EDGE PRO Manuel utilisateur
Zero Edge Pro
Installation Instructions
INSTALLERS: PLEASE LEAVE THIS MANUAL WITH THE OWNER.
400025 Ι v. 1.7 Ι 28 February
APPLY S/N
STICKER HERE
Screen Innovations warrants its products, to the original purchaser only, to be free from defects in
materials and workmanship for a period of one (1) year from the date of purchase by the original
purchaser provided they are properly operated according to Screen Innovations' instructions and are
not damaged due to improper handling or treatment after shipment from the factory.
This warranty does not apply to equipment showing evidence of misuse, abuse, or accidental damage,
or which has been tampered with or repaired by a person other than authorized Screen Innovations
personnel.
Screen Innovations’ sole obligation under this warranty shall be to repair or to replace (at Screen
Innovations’ option) the defective part of the merchandise. Returns for service should be made to
your Screen Innovations' dealer. If it is necessary for the dealer to return the screen or part to Screen
Innovations, transportation expenses to and from Screen Innovations are payable by the purchaser and
Screen Innovations is not responsible for damage in shipment. To protect yourself against damage or
loss in transit, insure the product and prepay all transportation expenses.
mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives
is assumed for expenses or damages resulting from interruption in operation of equipment, or for
incidental, direct, or consequential damages of any nature.
In the event that there is a defect in materials or workmanship of a Screen Innovations product, you
Important: this warranty shall not be valid and screen innovations shall not be bound by this warranty if
the product is not operated in accordance with screen innovations' written instructions.
Keep your sales receipt to prove the date of purchase and your original ownership.
Limited 1 year warranty
on Screen Innovations products
SUGGESTED PROJECTOR PLACEMENT.............................................1
DETERMINE FRAME TYPE.........................................................
....................................................
....................................................
.....................................................
LED LIGHTS ATTACHMENT...................................................
MATERIAL ATTACHMENT SEQUENCE .............................................11
DETERMINE YOUR MATERIAL ....................................................11
...............................
................................................
..........................
PVC – AT MATERIAL – SLATE, UNITY, PURE AT ATTACHMENTS ......................
...........................
SMALL TRIM ATTACHMENT.................................................
MEDIUM TRIM ATTACHMENT ...............................................
LOGO ATTACHMENT ............................................................
...............................................................
..............................................................
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IP CONTROLLED LIGHTING SETUP................................................
TABLE OF CONTENTS
Hours of Support: 7:30am – 5pm CST | screeninnovations.com
Please visit support.screeninnovations.
com to nd all the updated documents,
drivers and tutorial videos.
Use this QR code to see the video
tutorials for Black Diamond or Short
Throw snap attachment method
Use this QR code to see the
video tutorials for Slate material.
1
11°
11°
SCREEN
Better
Best
Good
36”-42”
(91cm - 106cm)
SUGGESTED PROJECTOR PLACEMENT
wizard/) for the minimum throw distance requirements based on screen material.
2
5
DETERMINE FRAME TYPE
Note: The vertical support bar is for certain models and sizes only.
Split Frame
Standard Frame
3
2
in the corners.
1
STANDARD FRAME ASSEMBLY
Insert the thin corner brackets into the outside channels and the thick corner brackets into the
inside channels of the vertical frames. Then slide into the channels in the horizontal frames.
Thin Bracket
Thick
If using AT or Maestro material, check to make sure the channel nuts are installed in the
inner channel before proceeding.
4
It is a critical step to square the frame. Refer to the illustration below.
A
3
4Measure the diagonals to check if frame is square. If one diagonal is longer, push the
corners at the diagonal. Tighten all set screws once the diagonals are equal or within
Note: If LED lights were ordered, refer to page 9
to for instructions on attaching LED lights to the
screen frame.
STANDARD FRAME ASSEMBLY
5
1
SPLIT FRAME ASSEMBLY
If using AT or Maestro material, ensure the channel nuts are installed in the inner channel
before proceeding.
Insert the thin corner brackets into the outside channels and the thick corner brackets into
the inside channels of the vertical frames. Slide backets into the channels in the horizontal
frames.
Thin
Bracket
Thick
6
2Slide the horizontal frame pieces together and secure with the splice bars. Attach the vertical
support to the frame as shown. Fully tighten splice bars, leaving the vertical support bar loose
but snug.
SPLIT FRAME ASSEMBLY
7
3
in the corners.
SPLIT FRAME ASSEMBLY
Autres manuels pour ZERO EDGE PRO
1
Table des matières
Autres manuels Screen Innovations Écran de projection
Screen Innovations
Screen Innovations Solo 2 Manuel utilisateur
Screen Innovations
Screen Innovations 5 Series Zero Edge Manuel utilisateur
Screen Innovations
Screen Innovations Solo 3 Indoor 575 External Manuel utilisateur
Screen Innovations
Screen Innovations 5 Series Fixed Manuel utilisateur
Screen Innovations
Screen Innovations Transformer Manuel utilisateur
Screen Innovations
Screen Innovations Solo Manuel utilisateur
Screen Innovations
Screen Innovations 7 Series Fixed Manuel utilisateur
Screen Innovations
Screen Innovations Solo 3 Manuel utilisateur
Screen Innovations
Screen Innovations 7 Series Fixed Manuel utilisateur
Screen Innovations
Screen Innovations 5 Motorized Manuel utilisateur
Screen Innovations
Screen Innovations Zero-G Manuel utilisateur
Screen Innovations
Screen Innovations 5 Series Curved Fixed Manuel utilisateur
Screen Innovations
Screen Innovations Solo Manuel utilisateur
Screen Innovations
Screen Innovations Solo/Pro 2 Manuel utilisateur
Screen Innovations
Screen Innovations 1 SERIES FIXED Manuel utilisateur
