Schwank UHE Mode d'emploi

UHE-F / EIH-F I&O Manual

IM100205

RD: APR 2019

RL: 02C

INSTALLATION / OWNER’S MANUAL

Improper installation, adjustment, alteration, service or

maintenance can cause property damage, injury or death.

Read the installation and operating and maintenance instruc-

tions thoroughly before installing or servicing this equipment.

SAFETY ALERT:

This heater must be installed and serviced only by a trained gas service techni-

cian. Failure to comply could result in personal injury, death, fire and/or property

damage.

Do not store or use gasoline or other flammable vapours and liquids in the

vicinity of this or any other gas fired appliance.

IF YOU SMELL GAS:

◼ Extinguish any open flame

◼ Do not attempt to light this or any other appliance

◼ Don’t touch any electrical switch, or telephone

◼ Immediately call your gas supplier from a neighbor’s phone

◼ Follow any and all instruction from your gas supplier

◼ If your gas supplier is not available, call the fire department



FIELD CONVERTIBILITY:

This appliance is not field

convertible to Propane.

Keep this manual in a secure place 

:

Model #:

Serial #:



HIGH RADIANT OUTPUT LOW INTENSITY TUBE TYPE INFRA RED HEATER

Certified to ANSI Z83.20 / CSA 2.34 Latest Edition



UHE



EIH

UHE-F / EIH-F I&O Manual

IM100205

RD: APR 2019

RL: 02C

NOTICE:

            









-Schwank and InfraSave











--

--

-





UHE-F / EIH-F I&O Manual

IM100205

RD: APR 2019

RL: 02C



 ........ 

IMPORTANT INFORMATION - READ FIRST

 ............................................. 4

........................... 5, 27

............................... 5, 27

 ................................................ 5, 17

‘’.................................... 5

....... 5

‘’.............................................. 6

 ........... 6

Clearances Figure & Table ........................... 7

...................... 8

1. LABOR REQUIREMENTS............................... 8

2. INSTALLATION IN AIRCRAFT HANGARS..... 8

3. INSTALLATION IN COMMERCIAL

GARAGES ....................................................... 9

4. INSTALLATIONS OTHER THAN

SPACE HEATING ............................................ 9

5. PRE-INSTALLATION SURVEY ....................... 9

6. MOUNTING CLEARANCES .......................... 10

SERVICE CLEARANCE ................................ 10

HEATER PLACEMENT GUIDELINES .......... 11

7. SYSTEMS INCORPORATING 90°

AND 180° ELBOWS ..................................... 12

ELBOW KIT DIMENSIONS .………………….12

8. SUSPENDING THE SYSTEM ....................... 13

8a. SEIZMIC RESTRAINT…………………………15

8b. WIND RESTRAINT…………………………….15

9. TUBE / REFLECTOR INSTALLATION .......... 16

TURBULATORS ............................................ 19

SPECIAL COUPLING - 160 & 200 Mbh..20 & 21

10. BURNER INSTALLATION .............................22

11. FLUE VENTING .............................................23

……...

12. COMBUSTION AIR DUCT .............................. 29

13. GAS SUPPLY ................................................. 30

HEATER EXPANSION .................................... 31

FLEXIBLE GAS CONNECTION ...................... 32

14. ELECTRICAL AND THERMOSTAT ................ 33

15. HIGH ALTITUDE INSTALLATION................... 33

16. LIGHTING INSTRUCTIONS .............. .............33

17. RECOMMENDED MAINTENANCE .............. ..33

18. WIRING DIAGRAM: FENWAL DSI ................. 34

19. WIRING DIAGRAM MULTIPLE HEATERS

PER THERMOSTAT .................................... 35

20. FENWAL DSI: SEQUENCE OF OPERATION ......... 36

SPARK IGNITER SET UP ............................... 38

21. FENWAL DSI: TROUBLESHOOTING GUIDE......... 39

22. TROUBLESHOOTING GUIDE: HEATER ................ 40

23. START– UP / COMMISSIONING SHEET ...... 42

WARRANTY STATEMENT................ BACK PAGE



24. HEATER DIMENSIONS / WEIGHTS ………44

25. HANGER INSTALLATION DIMENSIONS…. ..45

26. BURNER / TUBE KIT ASSEMBLY CHARTS

UHE / EIH ………………………..………....47

27. HIGH ALTITUDE ORIFICE CHART................. 48

28. OPTIONAL ACCESSORIES ............................ 49

29. BURNER PARTS LIST ................................... 52

30. TUBE SYSTEM PARTS LIST .......................... 54



HONEYWELL S87J DSI............................. 54 - 56



HIGH RADIANT OUTPUT GAS INFRARED TUBE HEATER

-

UHE-F / EIH-F I&O Manual

IM100205

RD: APR 2019

RL: 02C



This appliance has been certified by CSA International to ANSI Z83.20 / CSA 2.34 latest edi-

tion.

A gas-fired radiant tube heater may be installed for heating of commercial / industrial non-

residential spaces. It is beyond the scope of these instructions to consider all conditions that

may be encountered. Installation must conform with all local building codes or, in the absence

of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 in the U.S.A. or the

Natural Gas and Propane Installation Code, CSA B149.1 in Canada. The latest edition Electri-

cal Code ANSI/NFPA N0 70 in the U.S.A. and PART 1 CSA C22.1 in Canada must also be ob-

served.

Installation of a gas fired tube heater must conform to all heating installation design procedures

including clearance to combustibles, connection to the gas and electrical supplies, and ventila-

tion.

This heater is not for installation in a Class 1 or Class 2 explosive environment, nor a resi-

dence. If installation of this equipment is in question, consult with local authorities having juris-

diction (Fire Marshall, labor department, insurance underwriter, or others).

Revisions to codes and/or standards, may require revision to equipment and installation proce-

dures. In case of discrepancy, the latest codes, standards, and installation manual will take pri-

ority over prior releases.

may be installed for heating of commercial / industrial non-residential



Improper installation, adjustment, alteration, service or maintenance can cause

property damage, injury or death. Read and understand this installation and op-

eration manual thoroughly prior to assembly, installation, operation or service to

this appliance.

This heater must be installed and serviced only by a trained gas service techni-

cian.

Do not store or use gasoline or other flammable vapours and liquids in the vicinity

of this or any other gas fired appliance.

Failure to comply could result in personal injury, death, fire and/or property dam-

age.

Do not store or use gasoline or other flammable vapours and liquids in the vicinity

of this or any other gas fired appliance.

This appliance may have sharp edges and corners. Wear protective clothing such

as gloves and protective eye wear when servicing this or any other appliance.

WARNING

California Proposition 65:

: This product can expose you to chemicals including carbon monoxide, which

is known to the State of California to cause birth defects or other reproductive harm. For more

information, go to www.P65Warnings.ca.gov

UHE-F / EIH-F I&O Manual

IM100205

RD: APR 2019

RL: 02C



It is a normal condition that during heat-up and cool-down a tube

heater will expand and contract. Allowances for heater expansion

must be made in the gas connection, venting and combustion air

ducting. Improper installation, alteration, or adjustment can result in

property damage, injury or death. 





Inadequate venting of a heater may result in asphyxiation, carbon

monoxide poisoning, injury or death. This heater may be directly or

indirectly vented from the space. Venting must be in accordance with

all local, state, provincial, and national codes (ANSI Z223.1/NFPA 54

in USA; B149.1 in Canada) and as indicated in this manual.



Improper installation, connection, or adjustment can result in property

damage, toxic gases, asphyxiation, injury or death. Using an ap-

proved flexible gas connector in the USA or Type 1 hose connector

in Canada, the gas supply to the heater must be connected and test-

ed in accordance with all local, state, provincial, and national codes (ANSI Z223.1/NFPA 54 in

USA; B149.1 in Canada) and as indicated in this manual. 



 -‘’ 

During start up, the heating of material coatings used in the production process of tubes and

reflectors will create smoke during the initial period of operation. This condition is normal and

temporary .

Ensure that there is sufficient ventilation to adequately clear any smoke from the space.

Notify site and safety personnel to ensure that alarm systems are not unduly activated.

 

Infrared radiant (IR) heating system provide comfort with the effect of radiant heat and ambient

air heat.

If your IR system is controlled with a thermostat (TruTemp or ThermoControl Plus) that senses

radiant heat, then set the thermostat to the desired comfort temperature (ie: 65°; 68°; 20°C).

If your IR system is controlled with a standard 24V or 120V thermostat that senses only air tem-

perature, then start with a thermostat setting that is 5° to 7°F (3° to 5°C) lower than the desired

comfort temperature. Some trial and error setting may be required to ‘fine tune’ the comfort tem-

perature that best suits your site and provides most economical operation.



UHE-F / EIH-F I&O Manual

IM100205

RD: APR 2019

RL: 02C



Location of flammable or explosive objects, liquids or vapors close to the heater may cause fire

or explosion and result in property damage, injury or death. Do not use, store or locate flamma-

ble or explosive objects, liquids or vapors in proximity of the heater.









’

         





In locations used for the storage of combustible materials, signs must be posted to specify the

maximum permissible stacking height to maintain the required clearances from the heater to

the combustibles. Such signs must either be posted adjacent to the heater thermostats or in

the absence of such thermostats in a conspicuous location. In addition to stored or stationary

material, consideration must also be given to moveable objects such as cranes, vehicles, and

overhead doors, and structural objects such as sprinkler heads, electrical and gas lines, and

electrical fixtures.

It is beyond the scope of these instructions to consider all conditions that may be encountered.

Consult local authorities such as the Fire Marshall, insurance carrier, or safety authorities if you

are uncertain as to the safety or applicability of the proposed installation.



.

WARNING

WARNING “”

It is a normal condition that the combustion tube (1st tube) can appear to “glow red”. For inputs

up to 150,000 Btuh, the top surface of the tube can appear red where heat is trapped between

the reflector and the tube. The stainless steel tube used for inputs 175,000 and greater can ap-

pear to entirely glow red. The tube material is designed into the heater because it can with-

stand the high temperature of combustion, and the “red glow” is a normal occurrence.

UHE-F / EIH-F I&O Manual

IM100205

RD: APR 2019

RL: 02C

(measured from the hanger)

-Table 1 

*The clearance to combustible materials represents the minimum distance that must be main-

tained between the heater and a nearby surface. 

.

 that in the above table the to facilitate the

correct locating of the heater during installation.

’







‘’, ‘’, ‘’, & ‘’ 

‘’ 

















inches (cm)



inches (cm)



inches (cm)



inches (cm)



inches (cm)



inches (cm)



inches (cm)

UHE / EIH 60 

(1.25)

(41) (114.3) (2.5)  (8.3) (89) (104)

UHE / EIH 90  (3.2) (66) (178) (6.4)  (13.3) (127) (152)

UHE / EIH 130 ( 4 ) (76.2) (218.5) (7.6)  (16) (145) (178)

UHE / EIH 160 (7.6) (114.3) (267) (14)  (25.4) (191) (216)

UHE / EIH 200 ( 9 )  (142.2)  (282)  (20.3)  (31.8)  (229)  (236)

Heaters mounted at an angle between 0° & 30° must maintain the greater clearance listed

for either 0° or 30°. (A or D; S or F, S or B; U or C)

UHE-F / EIH-F I&O Manual

IM100205

RD: APR 2019

RL: 02C

VENT END CLEARANCE: Clearances from the vent pipe are determined by local or national

installation codes, but must not be less than 6 inches (15 cm). For ‘unvented’ installation, a

minimum distance of 24 inches (61 cm) is required from the end of heater to a combustible

surface.



 specifying theto

maintain the required clearances from the heater to the combustibles.

The signs must be posted either adjacent to the IR heating system thermostats or in the ab-

sence of such thermostats, in a conspicuous place.

“” 







To calculate the value ‘’: ( =  - )

• Measure the on site distance between bottom

of the heater and the floor = ‘’ inches (cm).

• Subtract the clearance below the heater ‘’

from ‘’ (see Table 1 for the value ‘’ that corre-

sponds to the model you are installing).

• Enter this value ‘’ on the sign.

Refer to the information for the heater model

being installed in Figure 1 and Table 1 to get

the values for dimensions ‘’, ‘’ and ‘’.



 

Low intensity radiant tube heaters are suitable for use in aircraft hangars when installed in ac-

cordance with the latest edition of the Standard for , ANSI/NFPA No 409 in the

USA, or the Canadian , B149.1.

A. A minimum clearance of 10 ft (3 m) above either the highest fuel storage compartment or

the highest engine enclosure of the highest aircraft which may occupy the hangar. The

clearance to the bottom of the heater shall be measured from the upper surface of either

the fuel storage compartment or the engine enclosure, whichever is higher from the floor.

B. A minimum clearance of 8 ft (2.4 m) must be maintained from the bottom of the heater to

the floor in other sections of the aircraft hangar, such as offices and shops, which communi-

cate with areas for servicing or storage. Refer to Section 1 for proper mounting clearances

to combustibles.

C. Heaters must be located so as to be protected from damage by aircraft and other objects,

such as cranes and movable scaffolding.

D. Heaters must be located so as to be accessible for servicing and adjustment.

WARNING

 

Two persons are required to safely install this equipment. Each insulated reflector assembly

weighs approximately 50 pounds (23 kg). Wear gloves and other required safety protection.

UHE-F / EIH-F I&O Manual

IM100205

RD: APR 2019

RL: 02C



Low Intensity Heaters are suitable for use in commercial garages when installed in accordance

with the latest edition of the Standard for , ANSI/NFPA 88A, or the Standard

for , ANSI/NFPA No. 88B, or the Canadian 

, B149.1.

An overhead heater shall be located high enough to maintain the mini-

mum distance to combustibles, as shown on the heater rating plate, from

the heater to any vehicles parked below the heater.

Overhead heaters shall be installed at least 8 ft (2.4 m) above the floor.

 

Use for process or other applications that are not space heating will void the C.S.A. certification

and product warranty. Process application requires field inspection and/or certification by local

authorities having jurisdiction.

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause

property damage, injury or death. Read and understand this installation and

operation manual thoroughly prior to assembly, installation, operation or service to

this appliance.

This heater must be installed and serviced only by a trained gas service technician.

Do not store or use gasoline or other flammable vapours and liquids in the vicinity

of this or any other gas fired appliance.

Failure to comply could result in personal injury, death, fire and/or property damage.

Do not store or use gasoline or other flammable vapours and liquids in the vicinity

of this or any other gas fired appliance.

WARNING

 

It is recommended that a full heating design including heat loss calculation be conducted on

the structure or area to be heated. Heater sizing and placement must consider available

mounting height, sources of greatest heat loss, and the certified clearances to combustibles

with respect to stored material, moveable objects (cranes, vehicles, lifts, overhead doors, etc),

sprinkler system heads, and other obstructions on the site. Consideration must also be given to

vent / duct placement and the allowable combined lengths of vent and duct. Carefully survey

the area to be heated, and for best results place burner and combustion chamber in the coldest

area(s).

UHE-F / EIH-F I&O Manual

IM100205

RD: APR 2019

RL: 02C

Installation must conform with all local, state, provincial and national code requirements includ-

ing the current latest edition ANSI Z223.1 (NFPA 54) in the U.S.A. and B149.1 installation

code in Canada, for gas burning appliances and equipment. The latest edition Electrical Code

ANSI/NFPA N0 70 in the U.S.A. and PART 1 CSA C22.1 in Canada must also be observed.

The heating system must have gas piping of the correct diameter, length, and arrangement to

function properly. For this reason, a layout drawing is necessary.

 

This heater must be mounted with at least the minimum clearances between the heater and

combustibles as shown in FIG-1, TABLE 1, Page 3. It is the installer’s responsibility to ensure

that building materials with a low heat tolerance which may degrade at lower temperatures are

protected to prevent degradation. Examples of low heat tolerance materials include vinyl sid-

ing, fabrics, some plastics, filmy materials, etc.

Positioning of lights, sprinkler heads, overhead doors, storage areas, gas and electrical lines,

parked vehicles, cranes and any other possible obstruction or hazard must be evaluated prior

to installation.





   : The lower ‘jaw’ of the burner cabinet swings down to provide

convenient service access to burner components. Provide a minimum clearance from any wall

or obstruction of 6 inches (15 cm) to the access end of the burner housing, and a minimum of

24 inches (61 cm) to any ONE side to allow servicing of burner, blower and controls. (see Fig-

ure 2) - the minimum clearances to combustibles must always be maintained.

For guidelines to heater placement refer to TABLE 2 (below).



Autres manuels pour UHE

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Schwank Chauffage

Schwank

Schwank infrasave SET Series Mode d'emploi

Schwank

Schwank UHE Instructions d'installation

Schwank

Schwank sportSchwank Series Instructions d'installation

Schwank

Schwank deltaSchwank Series Manuel utilisateur

Schwank

Schwank STS-JZ Mode d'emploi

Schwank

Schwank STV-JZ Manuel utilisateur

Schwank

Schwank 4003 series Manuel utilisateur

Schwank

Schwank SEM 200-70 Instructions d'installation

Schwank

Schwank ECOSCHWANK-MILLIVOLT Mode d'emploi

Schwank

Schwank Epic14 Series Manuel utilisateur

Schwank

Schwank SchwankAir 4000-Recessed Series Manuel utilisateur

Schwank

Schwank ECOSCHWANK-MILLIVOLT Mode d'emploi

Schwank

Schwank bistroSchwank Series Mode d'emploi

Schwank

Schwank STS-JZ Mode d'emploi

Schwank

Schwank SST-MX Series Mode d’emploi

Schwank

Schwank STW-JZ Manuel utilisateur

Schwank

Schwank Swift5 Series Manuel utilisateur

Schwank

Schwank S100 Mode d'emploi

Schwank

Schwank novoSchwank D 20S U Manuel utilisateur

Schwank

Schwank infraSchwank D 40U Manuel utilisateur

Schwank

Schwank P40U Manuel utilisateur

Schwank

Schwank InfraSave 2100 Manuel utilisateur

Schwank

Schwank 20S L Manuel utilisateur

Schwank

Schwank infraSchwank D Series Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur