Schwank UHE Instructions d'installation

UHE / EIH I&O Manual

IM100205

RD: MAY 2013

RL: 03D

INSTALLATION / OWNER’S MANUAL

Improper installation, adjustment, alteration, service or

maintenance can cause property damage, injury or death.

Read the installation and operating and maintenance instruc-

tions thoroughly before installing or servicing this equipment.

SAFETY ALERT:

This heater must be installed and serviced only by a trained gas service techni-

cian. Failure to comply could result in personal injury, death, fire and/or property

damage.

Do not store or use gasoline or other flammable vapours and liquids in the

vicinity of this or any other gas fired appliance.

IF YOU SMELL GAS:

 Extinguish any open flame

 Do not attempt to light this or any other appliance

 Don’t touch any electrical switch, or telephone

 Immediately call your gas supplier from a neighbor’s phone

 Follow any and all instruction from your gas supplier

 If your gas supplier is not available, call the fire department

WARNING

FIELD CONVERTIBILITY:

This appliance is not field

convertible to LP gas.

Keep this manual in a secure place .

Record for future reference:

Model #:

Serial #:

(located on heater rating label)

HIGHRADIANTOUTPUTLOW INTENSITYTUBETYPE INFRAREDHEATER

Certified toANSI Z83.20 /CSA2.34 LatestEdition

ultraSchwank

Model: InfraSave Ultimate

Model:

UHE EIH

UHE / EIH I&O Manual

IM100205

RD: MAY 2013

RL: 03D

NOTICE:

This manual is current for this product. Occasional revision of the product Certification Stan-

dard may require changes to the product and/or this manual.

This publication, or parts thereof, may not be reproduced in any form, without prior written

consent from The Manufacturer. Unauthorized use or distribution of this publication is

strictly prohibited.

Schwank Group

Schwank and InfraSave brands

5285 Bradco Boulevard

Mississauga, Ontario,L4W 2A6

PO Box 988, 2 Schwank Way

Waynesboro, Georgia 30830

Customer & Technical Services

Phone: 877-446-3727

Fax: 866-361-0523

e-mail: [email protected]

www.schwankgroup.com

www.infrasave.com

3 UHE / EIH I&O Manual

IM100205

RD: MAY 2013

RL: 03D

TABLE OF CONTENTS

TOPIC .........PAGE

INSTALLATION

IMPORTANT INFORMATION - READ FIRST

APPLICATION..............................................4

HEATER EXPANSION ...........................5, 27

GAS CONNECTION ...............................5, 27

See also “Flexible Gas Connection”......27

VENTING.................................................5, 17

START UP ‘SMOKE’....................................5

CLEARANCE TO COMBUSTIBLES............6

Clearances Figure & Table............................7

STACKING HEIGHT SIGN ......................8

1. LABOR REQUIREMENTS ...............................8

2. INSTALLATION IN AIRCRAFT HANGARS .....8

3. INSTALLATION IN COMMERCIAL

GARAGES........................................................9

4. INSTALLATIONS OTHER THAN

SPACE HEATING.............................................9

5. PRE-INSTALLATION SURVEY........................9

6. MOUNTING CLEARANCES...........................10

SERVICE CLEARANCE.................................10

HEATER PLACEMENT GUIDELINES...........11

7. SYSTEMS INCORPORATING 90°

AND 180° ELBOWS......................................12

ELBOW KIT DIMENSIONS .………………….12

8. SUSPENDING THE SYSTEM........................13

9. TUBE / REFLECTOR INSTALLATION...........15

TURBULATORS.............................................18

SPECIAL COUPLING - 160 & 200 Mbh..19 & 20

10. BURNER INSTALLATION.............................21

11. FLUE VENTING.............................................22

11A COMBINED SYSTEM LENGTH: Tube + Vent +

Combustion Air Duct .................................25

TOPIC ……...PAGE

12. COMBUSTION AIR DUCT...............................26

13. GAS SUPPLY ..................................................27

HEATER EXPANSION.....................................28

FLEXIBLE GAS CONNECTION.......................29

14. ELECTRICAL AND THERMOSTAT.................30

15. HIGH ALTITUDE INSTALLATION...................30

16. LIGHTING INSTRUCTIONS ...........................30

17. RECOMMENDED MAINTENANCE.................30

18. WIRING DIAGRAM..........................................31

19. WIRING DIAGRAM MULTIPLE HEATERS

PER THERMOSTAT.....................................32

20. SEQUENCE OF OPERATION.........................33

21. TROUBLESHOOTING GUIDE.........................34

22. SPARK IGNITION CIRCUIT ............................36

SPARK IGNITER SET UP...............................36

23. FLAME SENSING CIRCUIT ............................37

24. START– UP / COMMISSIONING SHEET.......38

PRODUCT DIMENSIONS & DATA

25. HEATER DIMENSIONS / WEIGHTS ………40

INSTALLATION DIMENSIONS ………. ..41

26. BURNER / TUBE KIT ASSEMBLY CHARTS

UHE / EIH ………………………..………....42

27. HIGH ALTITUDE ORIFICE CHART.................43

26. OPTIONAL ACCESSORIES.............................44

29. BURNER PARTS LIST ....................................47

30. TUBE SYSTEM PARTS LIST...........................49

WARRANTY STATEMENT ............BACK PAGE

ultraSchwank & InfraSave Ultimate SERIES

HIGH RADIANT OUTPUT GAS INFRARED TUBE HEATER

Model UHE / EIH - Indoor Commercial / Industrial

UHE / EIH I&O Manual

IM100205

RD: MAY 2013

RL: 03D

APPLICATION

This appliance has been certified by CSA International to ANSI Z83.20 / CSA 2.34 latest edi-

tion.

A gas-fired radiant tube heater may be installed for heating of commercial / industrial non-

residential spaces. It is beyond the scope of these instructions to consider all conditions that

may be encountered. Installation must conform with all local building codes or, in the absence

of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 in the U.S.A. or the

Natural Gas and Propane Installation Code, CSA B149.1 in Canada. The latest edition Electri-

cal Code ANSI/NFPA N0 70 in the U.S.A. and PART 1 CSA C22.1 in Canada must also be ob-

served.

Installation of a gas fired tube heater must conform to all heating installation design procedures

including clearance to combustibles, connection to the gas and electrical supplies, and ventila-

tion.

This heater is not for installation in a Class 1 or Class 2 explosive environment, nor a resi-

dence. If installation of this equipment is in question, consult with local authorities having juris-

diction (Fire Marshall, labor department, insurance underwriter, or others).

Revisions to codes and/or standards, may require revision to equipment and installation proce-

dures. In case of discrepancy, the latest codes, standards, and installation manual will take pri-

ority over prior releases.

Models UHE, EIH may be installed for heating of commercial / industrial non-residential

indoor spaces.

Improper installation, adjustment, alteration, service or maintenance can cause

property damage, injury or death. Read and understand this installation and op-

eration manual thoroughly prior to assembly, installation, operation or service to

this appliance.

This heater must be installed and serviced only by a trained gas service techni-

cian.

Do not store or use gasoline or other flammable vapours and liquids in the vicinity

of this or any other gas fired appliance.

Failure to comply could result in personal injury, death, fire and/or property dam-

age.

Do not store or use gasoline or other flammable vapours and liquids in the vicinity

of this or any other gas fired appliance.

This appliance may have sharp edges and corners. Wear protective clothing such

as gloves and protective eye wear when servicing this or any other appliance.

WARNING

5 UHE / EIH I&O Manual

IM100205

RD: MAY 2013

RL: 03D

Heater Expansion

It is a normal condition that during heat-up and cool-down a tube

heater will expand and contract. Allowances for heater expansion

must be made in the gas connection, venting and combustion air

ducting. Improper installation, alteration, or adjustment can result in

WARNING

Venting

Inadequate venting of a heater may result in asphyxiation, carbon

monoxide poisoning, injury or death. This heater may be directly or

indirectly vented from the space. Venting must be in accordance with

all local, state, provincial, and national codes (ANSI Z223.1/NFPA 54 in USA;

B149.1 in Canada) and as indicated in this manual. Refer to Sections 11 & 12

Gas Connection

Improper installation, connection, or adjustment can result in property

damage, toxic gases, asphyxiation, injury or death. Using an ap-

proved flexible gas connector in the USA or Type 1 hose connector in

Canada, the gas supply to the heater must be connected and tested in accordance with all lo-

cal, state, provincial, and national codes (ANSI Z223.1/NFPA 54 in USA; B149.1 in Canada)

and as indicated in this manual. Refer to Section 13

WARNING

WARNING Start-Up ‘SMOKE’ Condition

During start up, the heating of material coatings used in the production process of tubes and

reflectors will create smoke during the initial period of operation. This condition is normal and

temporary .

Ensure that there is sufficient ventilation to adequately clear any smoke from the space.

Notify site and safety personnel to ensure that alarm systems are not unduly activated.

UHE / EIH I&O Manual

IM100205

RD: MAY 2013

RL: 03D

Clearance to combustibles

Location of flammable or explosive objects, liquids or vapors close to the heater may cause fire

or explosion and result in property damage, injury or death. Do not use, store or

locate flammable or explosive objects, liquids or vapors in proximity of the heater.

The clearance to combustible material represents the minimum dis-

tance that must be maintained between the outer heater surface and

a nearby surface. The stated clearance to combustibles represents a

surface temperature of 90F° (50C°) above room temperature. It is the

installer’s responsibility to ensure that building materials with a low

heat tolerance which may degrade at lower temperatures are pro-

tected to prevent degradation. Examples of low heat tolerance mate-

rials include vinyl siding, fabrics, some plastics, filmy materials, etc.

In locations used for the storage of combustible materials, signs must be posted to specify the

maximum permissible stacking height to maintain the required clearances from the heater to

the combustibles. Such signs must either be posted adjacent to the heater thermostats or in

the absence of such thermostats in a conspicuous location. In addition to stored or stationary

material, consideration must also be given to moveable objects such as cranes, vehicles, and

overhead doors, and structural objects such as sprinkler heads, electrical and gas lines, and

electrical fixtures.

It is beyond the scope of these instructions to consider all conditions that may be encountered.

Consult local authorities such as the Fire Marshall, insurance carrier, or safety authorities if you

are uncertain as to the safety or applicability of the proposed installation.

Refer to Figure 1 and Table 1 for the certified clearances to combustibles for the appro-

priate model input/size.

WARNING

7 UHE / EIH I&O Manual

IM100205

RD: MAY 2013

RL: 03D

TABLE 1 MINIMUM CLEARANCES TO COMBUSTIBLES* (measured from the hanger)

FIGURE 1 MINIMUM CLEARANCES TO COMBUSTIBLES* - refer to Table 1 for values

*The clearance to combustible materials represents the minimum distance that must be main-

tained between the heater and a nearby surface. The stated clearance to combustibles

represents a surface temperature of 90F° (50C°) above room temperature. .

NOTE that in the above table the clearances are measured from the hanger to facilitate the

correct locating of the heater during installation.

It is the installer’s responsibility to ensure that building materials with a low heat toler-

ance which may degrade at lower temperatures are protected to prevent degradation.

Examples of low heat tolerance materials include vinyl siding, fabrics, some plastics,

filmy materials, etc.

NOTE: USE AN INDELIBLE MARKER TO ENTER VALUES ‘H’, ‘S’, ‘F’, & ‘B’ ON

THE ‘PEEL & STICK’ SIGN PROVIDED.

POST THE SIGN ADJACENT TO THE HEATER THERMOSTAT OR IN A

PROMINENT LOCATION. See next page for details.

MODEL SUSPENDED

HORIZONTALLY SUSPENDED AT AN ANGLE

OF 30 DEGREES

inches (cm) S

inches (cm) U

inches (cm) D

inches (cm) B

inches (cm) F

inches (cm) C

inches (cm)

UHE / EIH 60 0.5 (1.25) 16 (41) 45 (114.3) 1.0 (2.5) 3.25 (8.3) 35 (89) 41 (104)

UHE / EIH 90 1.25 (3.2) 26 (66) 70 (178) 2.5 (6.4) 5.25 (13.3) 50 (127) 60 (152)

UHE / EIH 130 1.5 ( 4 ) 30 (76.2) 86 (218.5) 3.0 (7.6) 6.25 (16) 57 (145) 70 (178)

UHE / EIH 160 3.0 (7.6) 45 (114.3) 105 (267) 5.5 (14) 10 (25.4) 75 (191) 85 (216)

UHE / EIH 200 3.5 ( 9 ) 56 (142.2) 111 (282) 8.0 (20.3) 12.5 (31.8) 90 (229) 93 (236)

Heaters mounted at an angle between 0° & 30° must maintain the greater clearance listed

for either 0° or 30°. (A or D; S or F, S or B; U or C)

UHE / EIH I&O Manual

IM100205

RD: MAY 2013

RL: 03D

VENT END CLEARANCE: Clearances from the vent pipe are determined by local or national

installation codes, but must not be less than 6 inches (15 cm). For ‘unvented’ installation, a

minimum distance of 24 inches (61 cm) is required from the end of heater to a combustible

surface. In locations used for the storage of combustible materials: Signs

must be posted specifying the maximum permissible stacking height to

maintain the required clearances from the heater to the combustibles.

The signs must be posted either adjacent to the IR heating system thermostats or in the ab-

sence of such thermostats, in a conspicuous place.

For your convenience a “peel and stick” sign

is provided with this heater. Use a permanent

marker to record the required dimensions on

the sign.

To calculate the value ‘H’: (H= T- C)

 Measure the on site distance between bottom

of the heater and the floor = ‘T’ inches (cm).

 Subtract the clearance below the heater ‘C’

from ‘T’ (see Table 1 for the value ‘C’ that corre-

sponds to the model you are installing).

 Enter this value ‘H’ on the sign.

Refer to the information for the heater model

being installed in Figure 1 and Table 1 to get

the values for dimensions ‘S’, ‘F’ and ‘B’. Post this sign as instructed above.

2. INSTALLATION IN COMMERCIAL AIRCRAFT HANGARS

Low intensity radiant tube heaters are suitable for use in aircraft hangars when installed in ac-

cordance with the latest edition of the Standard for Aircraft Hangars, ANSI/NFPA No 409 in the

USA, or the Canadian Natural Gas and Propane Installation Code, B149.1.

A. A minimum clearance of 10 ft (3 m) above either the highest fuel storage compartment or

the highest engine enclosure of the highest aircraft which may occupy the hangar. The

clearance to the bottom of the heater shall be measured from the upper surface of either

the fuel storage compartment or the engine enclosure, whichever is higher from the floor.

B. A minimum clearance of 8 ft (2.4 m) must be maintained from the bottom of the heater to

the floor in other sections of the aircraft hangar, such as offices and shops, which communi-

cate with areas for servicing or storage. Refer to Section 1 for proper mounting clearances

to combustibles.

C. Heaters must be located so as to be protected from damage by aircraft and other objects,

such as cranes and movable scaffolding.

D. Heaters must be located so as to be accessible for servicing and adjustment.

WARNING

1. LABOR REQUIRMENTS

Two persons are required to safely install this equipment. Each insulated reflector assembly

weighs approximately 50 pounds (23 kg). Wear gloves and other required safety protection.

9 UHE / EIH I&O Manual

IM100205

RD: MAY 2013

RL: 03D

3. INSTALLATION IN COMMERCIAL GARAGES AND PARKING STRUCTURES

Low Intensity Heaters are suitable for use in commercial garages when installed in accordance

with the latest edition of the Standard for Parking Structures, ANSI/NFPA 88A, or the Standard

for Repair Garages, ANSI/NFPA No. 88B, or the Canadian Natural Gas and Propane Installa-

tion Code, B149.1.

An overhead heater shall be located high enough to maintain the mini-

mum distance to combustibles, as shown on the heater rating plate, from

the heater to any vehicles parked below the heater.

Overhead heaters shall be installed at least 8 ft (2.4 m) above the floor.

4. INSTALLATIONS OTHER THAN SPACE HEATING

Use for process or other applications that are not space heating will void the C.S.A. certification

and product warranty. Process application requires field inspection and/or certification by local

authorities having jurisdiction.

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause

property damage, injury or death. Read and understand this installation and

operation manual thoroughly prior to assembly, installation, operation or service to

this appliance.

This heater must be installed and serviced only by a trained gas service technician.

Do not store or use gasoline or other flammable vapours and liquids in the vicinity

of this or any other gas fired appliance.

Failure to comply could result in personal injury, death, fire and/or property damage.

Do not store or use gasoline or other flammable vapours and liquids in the vicinity

of this or any other gas fired appliance.

WARNING

5. PRE INSTALLATION SURVEY

It is recommended that a full heating design including heat loss calculation be conducted on

the structure or area to be heated. Heater sizing and placement must consider available

mounting height, sources of greatest heat loss, and the certified clearances to combustibles

with respect to stored material, moveable objects (cranes, vehicles, lifts, overhead doors, etc),

sprinkler system heads, and other obstructions on the site. Consideration must also be given to

vent / duct placement and the allowable combined lengths of vent and duct. Carefully survey

the area to be heated, and for best results place burner and combustion chamber in the coldest

area(s).

UHE / EIH I&O Manual

IM100205

RD: MAY 2013

RL: 03D

Installation must conform with all local, state, provincial and national code requirements includ-

ing the current latest edition ANSI Z223.1 (NFPA 54) in the U.S.A. and B149.1 installation

code in Canada, for gas burning appliances and equipment. The latest edition Electrical Code

ANSI/NFPA N0 70 in the U.S.A. and PART 1 CSA C22.1 in Canada must also be observed.

The heating system must have gas piping of the correct diameter, length, and arrangement to

function properly. For this reason, a layout drawing is necessary.

6. MOUNTING CLEARANCES

This heater must be mounted with at least the minimum clearances between the heater and

combustibles as shown in FIG-1, TABLE 1, Page 3. It is the installer’s responsibility to ensure

that building materials with a low heat tolerance which may degrade at lower temperatures are

protected to prevent degradation. Examples of low heat tolerance materials include vinyl sid-

ing, fabrics, some plastics, filmy materials, etc.

Positioning of lights, sprinkler heads, overhead doors, storage areas, gas and electrical lines,

parked vehicles, cranes and any other possible obstruction or hazard must be evaluated prior

to installation.

Ensure adequate clearance around the air intake at the burner to allow sufficient com-

bustion air supply to the heater.

6A. SERVICE CLEARANCE: The lower ‘jaw’ of the burner cabinet swings down to provide

convenient service access to burner components. Provide a minimum clearance from any wall

or obstruction of 6 inches (15 cm) to the access end of the burner housing, and a minimum of

24 inches (61 cm) to any ONE side to allow servicing of burner, blower and controls. (see Fig-

ure 2) - the minimum clearances to combustibles must always be maintained.

For guidelines to heater placement refer to TABLE 2 (below).

FIGURE 2

Autres manuels pour UHE

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Schwank Chauffage

Schwank

Schwank 20S L Manuel utilisateur

Schwank

Schwank infraSchwank D Series Manuel utilisateur

Schwank

Schwank SchwankAir 3200-Recessed Series Manuel utilisateur

Schwank

Schwank infraSchwank D 40U Manuel utilisateur

Schwank

Schwank X-Series Mode d'emploi

Schwank

Schwank UHE Mode d'emploi

Schwank

Schwank STR-JZ Mode d'emploi

Schwank

Schwank InfraSave Manuel utilisateur

Schwank

Schwank STW-JZ Manuel utilisateur

Schwank

Schwank Select12 Series Manuel utilisateur

Schwank

Schwank ecoSchwank-X 6 - IL-X 25 Mode d'emploi

Schwank

Schwank S100 Mode d'emploi

Schwank

Schwank Epic14 Series Manuel utilisateur

Schwank

Schwank STS-JZ Mode d'emploi

Schwank

Schwank SchwankAir 4000-Recessed Series Manuel utilisateur

Schwank

Schwank SCH-200-N Instructions d'installation

Schwank

Schwank STS-JZ Mode d'emploi

Schwank

Schwank STV-JZ Manuel utilisateur

Schwank

Schwank SchwankAir 2045 Manuel

Schwank

Schwank 20S L Manuel utilisateur

Schwank

Schwank sportSchwank Series Instructions d'installation

Schwank

Schwank Select14 Series Manuel utilisateur

Schwank

Schwank SPW2-JZ Series Mode d'emploi

Schwank

Schwank SchwankAir 4000 Series Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur