Schulze BluePRESSLine Size 3-S Manuel utilisateur
Instruction Manual
Version 10.01
Heat press
BluePRESSLine
Size 3-S
Version 10.01
1/16
1. Introduction
1.1 Content
1. Introduction 02
1.1 Content 02
1.2 Illustration of the heat press 03
1.3 Technical Data 03
1. Safety arrangements of the heat press 0
1.5 Safety arrangements at the workspace 0
2. Initiation 05
2.1 Tips for transport 05
2.2 Installation of the heat press 05
2.3 Power supply 05
2. Initiation of the heat press 05
3. Working with the heat ress 06
3.1 Programming of electronic devices 06
3.2 Bugfixing of the electronic devices 07
3.3 ECO Mode 07
3. Preßpressing 07
3.5 Application range and sample adjustments of the heat press 07
3.6 Pressure settings 08
3.7 Adjustment of the tension springs 08
3.8 Adjustment of the electromagnet 08
4. Maintenance 09
.1 Daily Maintenance 09
.2 Monthly Maintenance 09
.3 Replacing the main fuse 10
. Replacing the fuse in the power supply 10
.5 Replacing the electronic devices 11
.6 Replacing the power supply 11
.7 Replacing the silicon mat 12
.8 Replacing the thermal fuse 12
.9 Replacing the temperature sensor 13
.10 Troubleshooting 1
.11 Connection diagram 15
.12 Testing Report 16
.13 EC-Conformance declaration 16
Version 10.01
2/16
1.2 Illustration of the heat ress
1. Adjustment of the tension springs
2. Base plate with silicon mat
3. Heating plate
. Contact pressure adjustment
5. Electromagnet
6. Compression lever with rubber grip
7. Closing disk of electromagnet
8. Electronic devices
9. Enlargement plate
10. Main fuse
11. Main switch
12. coiled cabel
13. Connection cable
1.3 Technical Data
Dimensions of the press: ........................... 9 x 3 x 75 cm
Working plate: ................................................... 0 x 50 cm
Weight: ....................................................................... 35 kg
Operating voltage: ................................................ 230 VAC
Power with plate: ..................................................... 2, kW
Temeperature range: ......................................... 0 – 220° C
Time settings: .............................................. 1sek –20 min
Max. Pressure: ................................................... ca. 500 kg
Main fuse: ..................................................................... 12A
Version 10.01
3/16
1.4 Safety arrangements of the heat ress
The BluePRESLine Size 3-S is equipped with different safety arrangements, to make a safe usage possible.
Main fuse 12A
The main fuse 12A is placed in the pivoting upper part of the heat press. In case of overcharge, the main fuse prevents the heat press
from getting damaged.
Once the fuse was activated, it has to be replaced. The instruction for replacing the main fuse can be found in chapter .3.
Fuse 1,6A
This fuse is placed in the 12VAC power supply in the upper part of the heat press. It saves the 12VAC circuit of an overcharge. Once the
fuse was activated, it has to be replaced. The instruction for the exchange you can see in chapter . .
Thermal fuse
The thermal fuse is placed directly on the heating plate and it stops the power supply if the temperature exceeds 260°C. If this fuse is
activated, the temperature sinks down to 90°C. After that the power supply gets activated again and the temperature of the heating plate
rises and you can work with the press again. Certainly you need to install a new thermal fuse within the next days. The instruction for the
replacement of the thermal fuse can be found in chapter .8.
Acoustic signal
3 Seconds before the end of the pressing process an acoustic signal will sound.
Automatic switch-off
If the press doesn't get opened within 15 seconds after the pressing progress, the heating element switches off automatically, to avoid fire
danger.
1.5 Safety arrangements at the works ace
Set-u and installation of the heat ress
The set-up and installation of the press has to be controlled by an authorized person. Depending on the model and weight of the heat
press, the installation has to be done by 2 or more persons.
The instruction for the set-up and montage of the heat press can be found in chapter 2.2.
Testing the heat ress
After a correct installation of the press it is important to ensure that the press works properly, isn't damaged and has no safety defects. The
testing can only be done by the employer or other authorized persons and is mandatory to guarantee correct installation and safe usage of
the press. The testing should be protocoled.
If any irregularities regarding functionality or safety are found during the testing, these have to been noted and reported to Walter Schulze
GmbH in written form within 7 days. Until clarification the press can not be used.
Information and Education
According to § 81 industrial relations law and § 1 employment protection law the employer has to make arrangements to give all
information about the function and the range of application to the user.
In particular the user needs to be acquainted with the complete manual and be explicitly informed of the dangers of working with the press.
The details have to be explained in a coherent form and language.
Safety distance and ventilation
The press has to be installed at a place which gives enough space on both sides to put the material on.
The space in front of the press has to be wide enough to let nothing disturb the user at work.
Using the press with certain materials may create a strong smell. That’s why the user should evaluate the need for a ventilation system at
the workplace.
Safety instruction:
•The press should only be used by trained personal after notice of this manual
•Only one person is allowed to work on the press at a time.
•Beware of heating plate – risk of burns.
•The plug has to be pulled out of the power outlet while maintenance.
Version 10.01
4/16
2. Initiation
2.1 Ti s for trans ort
The BluePRESSLine Size 3-S is covered with a cardboard for transport. Right after the receiving you should check if the cardboard and
the press are in good condition. Later on, if you have to send the press somewhere, we ask you to cover the press with the same
cardboard and in the same way. The press has to be cold and the pressure lever has to be pulled down.
2.2 Installation of the heat ress
The heat press is delivered in a cardboard. After unpacking and connecting heat press can be worked with. The BluePRESSLine Size 3-S
heat press do not need any other installations.
2.3 Power su ly
The BluePRESSLine Size 3-S has to be connected to a voltage of 230VAC/ 50Hz. The press is equipped with a plug. Make sure that the
power outlet is in the right condition and that the grounding is connected to the power outlet.
2.4 Initiation of the heat ress
While powering up the press, the movable part has to be in the upper position, which means that the press has to be open. The press also
has to be open while heating up. The press can be turned on with the green switch. If the green switch glows the press heats up to the
adjusted temperature. After finishing the work with the press the switch has to be turned off and the plug has to be pulled out.
Version 10.01
5/16
3. Working with the heat ress
3.1 Programming the electronic devices
After switching on the press, the current temperature is shown on
the display and the press heats up.
Change settings:
1. The programming mode shows up when you press Button 1
for about 5 seconds, until the LED1 blinks up.
2. 2. LED1 blinks and the programmed temperature shows up.
The programming mode is activated.
3. The temperature gets programmed with button 2 and 3.
. Press Button 1 shortly.
On the display you now can see the programmed time. You
can adjust the time by pushing Button 2 and 3.
5. Press Button 1 shortly.
The display shows the programmed time for pre-pressing
With the Buttons 2 or 3 you can change the pre-pressing time
6. Press Button 1 shortly to save the changes and leave the
programming mode.
All settings are saved.
or
6. To get to the ECO programming, press Button 1 for 3
seconds.
7. With Button 2 and 3 you can switch between the ECO
modes:
„Eco 0” - ECO Mode turned off,
„Eco 1” - ECO Mode turned on, after 30 minutes temperature
drops 50°C, then after 60 minutes the heating elements turn
off.
„Eco 2” - ECO Mode turned on, after 60 minutes the
temperature drops 50°C, then after 60 minutes the heating
elements turn off.
„Eco 3” - ECO Mode turned on, after 120 minutes the
temperature drops 50°C, then after 60 minutes the heating
elements turn off.
8. Press Button 1 shortly.
With Button 2 and 3 you can select the desired sound
To leave the programming mode press Button 1.
TEMPERATURE TIME
Example: adjusted temperature 160°C
Control of the adjusted tem erature
If you want to control which temperature is adjusted at the
moment, press button 2(+). The temperature shows up on the
display.
Control of the adjusted time
If you want to control which time is adjusted at the moment, press
button 3(-). The time shows up on the display.
Version 10.01
6/16
3.2 Bugfixing of the electronic devices
The electronic devices of the BluePRESSLine Size 3-S heat press control the main functions of the press.
Here is a list of possible messages:
ERR.1 – No connection of the electronic devices to the temperature sensor, (Tem erature sensor defect/ cable not connected)
ERR.2 – Connection of electronic devices and temperature sensor bypassed , (Tem erature sensor defect/)
ERR.3 – Resistor of temperature sensor too low. The temperature range of the electronic devices is deceeded.
ERR. – Resistor of temperature sensor too high. The temperature range of the electronic devices exceeded.
ERR.5 – No temperature rise within 3 minutes even if heating element is switched on. (Tem erature fuse is defect)
ERR.6 – No reduction of the temperature within 3 minutes even if heating element is turned off. (Power relay CRYDOM is defect)
ERR.7 – Temperature too high, over 230°C (Power relay CRYDOM is defect)
ERR.3 and ERR. can occur if the electronic devices are not programmed properly.
3.3 “ECO” Mode
The "Eco" Mode is a special economic mode, which cools down the momentarily unused press about 50°C and turns off the heating
elements later. Both will be signaled acoustically.
The press gets activated again by pushing any button at the press.
3.4 Pre- ressing
The BluePRESSLine S heat press has a new function, the pre-pressing. Before closing the press, push Button 1 shortly (1 sec) to start
the pre-pressing.
3.5 A lication range and sam le adjustments of the heat ress
This press is used to put transfers and transferfilms on textiles. To get good achievements, get in contact with the producer of the textiles.
Here are some settings:
Film Flex 150°C – 160°C Time 15 Seconds
Film Flex S 155°C – 160°C Time 15 Seconds
Film A-Flex 155°C – 160°C Time 15 Seconds
Film Flock 160°C – 180°C Time 15 Seconds
Sublimation 150°C – 160°C Time 50 Seconds
All indications without warranty, please do your own testing before producing.
Version 10.01
7/16
ECO 0
- -
ECO 1 30 Minute 60 Minute
ECO 2 60 Minute 60 Minute
ECO 3 120Minute 60 Minute
temperature decreases turn off the heating
about -50°C elements later
3.6 Pressure adjustments
You can adjust the pressure very exactly. To do this, follow this explanation:
1. Put a textile on the workplate.
2. Close the heat press and control the pressure, after that, open the heat press.
•Turn the knop right to increase the pressure.
•Turn the knop left to decrease the pressure.
After every cahnge in the pressure adjusment, it is neccessary to close the heat press to control the new settings.
Damages, which results from a raised ressure adjustment, are barred from guarantee.
The fixation screws at the enlargement plate 1 and 2 have to be retighten after every pressure adjustment per hand.
3.7 Adjustment of the tension s rings
If you notice that heat press is not opening exactly and is too near to the base plate, you can change the adjustment of the tension springs.
The screw spring adjustment is on the front of the heating press. With this screw can you increase or decrease the tension. After that you
should check your new adjustment.
3.8 Adjustment of the electromagnet
The electromagnet holds the pressure lever and the heating
plate down while pressing and releases it when the pressing
time is over. It is adjusted at the factory.
Version 10.01
8/16
4. Maintenance
4.1 Daily Maintenance
The working surface of the heating plate and the base plate have to be clean. The heating plate can be cleaned with a clean, dry cloth.
Avoid contact with the heating plate – risk of burns. The silicon gum can be cleaned with a soft cloth. You can use mild household
detergent. Avoid scrub sponges, solvents or fuel.
4.2 Monthly Maintenance
Before beginning maintenance work, control if the ress is turned off and cold. Disconnect the press from electricity. Some movable
parts need to be greased. Greasing is needed after every 200 hours of usage. You can take normal car grease which is heat resistant
u to 160°C.
There are points on the heat press, which have to be greased after 200 hours of usage. While greasing you have to move the pressure
lever up and down slowly.
1. At the pressure lever, 2 little chambers ( hoto 1).
2. At the pressure lever, 2 little chambers ( hoto 2).
3. At the lower lever next to the base plate, 2 little chambers ( hoto 3).
. At the lower lever, 2 little chambers ( hoto 4).
Version 10.01
9/16
4.3 Re lacing the main fuse
If the heat press does not work after switching on, check the main fuse of the press.
The main fuse 12 A is placed at the upper part of the heat press next to the main switch ( hoto 1). To exchange the fuse, switch off the
heat ress first and ull the lug. There are additional fuses in the manual. Then remove the fuse bracket ( hoto 1). Pull out the main
fuse ( hoto 2). Replace the fuse ( hoto 3) and tighten the fuse bracket again ( hoto 4).
4.4 Re lacing the fuse in the ower su ly
To exchange the fuse, switch off the heat ress first and ull the lug. Remove the back cover ( hoto 1). Remove the bracket of the
fuse ( hoto 2) and pull out the fuse 1,6A ( hoto 3). Replace the fuse ( hoto 4) and tighten the fuse bracket again.
Version 10.01
10/16
Table des matières
Autres manuels Schulze Outils électriques
Schulze
Schulze Big-O-Matic 90130 Manuel utilisateur
Schulze
Schulze Pneu Press Manuel utilisateur
Schulze
Schulze BluePRESSLine Mug 4 plus Manuel utilisateur
Schulze
Schulze AirPress4 Guide rapide
Schulze
Schulze BluePRESSLine Mug 4 Manuel utilisateur
Schulze
Schulze Cap Press Manuel utilisateur
Schulze
Schulze Air press-4 X Manuel utilisateur
Schulze
Schulze E-Power Duo Press Manuel utilisateur
Schulze
Schulze DTG Press Manuel utilisateur
Schulze
Schulze BluePRESSLine DTG-4-S Manuel utilisateur
