Schmidt RM Series Manuel utilisateur

Thickness Gauge

RM Series

Model RMU-30

RMU-50

RMU-75

RMP-30

Edition RM 01.0.E

Instruction Manual

Valid as of: 05.07.2012• Please keep the manual for future reference!

1 Preparation

Before using the thickness gauge, check the cleanliness of the measuring surface and the

measuring pin. If necessary, clean with a dry, lint-free cloth.

2 Setup

The measuring pin with the upper measuring insert is pressed onto the lower measuring

insert and held in this position or locked with the locking screw.

By pressing the key „OFF / ON“, the measuring instrument is switched on and with the key

„0“ the zero point is adjusted.

With the function key „mm / inch“ you can select the desired scaling.

3 Measuring

The thickness gauge is ergonomically designed and allows a precise and fast measuring

with one hand.

The entire measuring range is available because the movable measuring pin is constantly

guided by spring force in the upper position.

During the measuring process, the material to be measured is scanned by the measuring

inserts.

By means of a finger, the measuring pin is carefully pressed onto the test material and the

measured value is determined.

The function key „0“ allows to set the zero point at any point in the measurement

range. This allows very fast measurements to deviations from given

Tolerances etc. are performed.

The thickness gauge can be switched of by pressing the ON / OFF key.

S C H M I D T

c o n t r o l i n s t r u m e n t s

4 Notes to maintenance

The thickness gauge should be kept dry all the time. Water and other liquids should be kept

away as they endanger the electronics.

The device should not be cleaned with acetone.

Battery replacement is carried out as follows:

1. Open battery compartment in direction of the arrow, remove the lid

2. Replace the old battery, altough paying attention to the correct position of the poles.

Insert the new battery.

3. Insert the battery cover and push toward.

5 Specifications

Measuring Range 0 - 30 mm, 0 - 50 mm, 0 - 75 mm

Scaling 0.01 mm / 0.0005 inch

Display Liquid crystal, height of digits 10 mm

sign (-)

Battery 1 Stück SR 44

Jaw Aluminium alloy, high-strength

Finishing plasticized/galvan. Ni

Mailing address:

P. O. B. 1154

84464 Waldkraiburg Germany

Shipping address:

Schichtstr. 16

84478 Waldkraiburg Germany

Hans Schmidt & Co GmbH

Phone:

int. + 49 / (0)8638 / 9410-0

Fax:

int. + 49 / (0)8638 / 4825

int. + 49 / (0)8638 / 67898

More than 70 years - Worldwide -

e-mail:

[email protected]

Internet:

http://www.hans-schmidt.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Schmidt Instrument de mesure

Schmidt

Schmidt SS 20.515 Manuel utilisateur

Schmidt

Schmidt ZT Series Manuel utilisateur

Schmidt

Schmidt SS 20.250 Manuel utilisateur

Schmidt

Schmidt DX Series Manuel utilisateur

Schmidt

Schmidt FS Series Manuel utilisateur

Schmidt

Schmidt DW-U Manuel utilisateur

Schmidt

Schmidt SS 20.600 E Series Manuel utilisateur

Schmidt

Schmidt D-2000 Series Manuel utilisateur

Schmidt

Schmidt DHT-2 Manuel utilisateur

Schmidt

Schmidt DX Series Manuel utilisateur

Schmidt

Schmidt FS Series Manuel utilisateur

Schmidt

Schmidt FG Series Manuel utilisateur

Schmidt

Schmidt MST Series Manuel utilisateur

Schmidt

Schmidt RS8000 Manuel utilisateur

Schmidt

Schmidt ZE Series Manuel utilisateur

Schmidt

Schmidt DW-D Manuel utilisateur

Schmidt

Schmidt DNW-100K Manuel utilisateur

Schmidt

Schmidt KXE-50 Manuel utilisateur

Schmidt

Schmidt Q-10 Manuel utilisateur

Schmidt

Schmidt D-2005 Series Manuel utilisateur

Schmidt

Schmidt SHT Series Manuel utilisateur

Schmidt

Schmidt DX2-50 Manuel utilisateur

Schmidt

Schmidt DXK Manuel utilisateur

Schmidt

Schmidt DN Series Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur