Schiit VIDAR 2 Manuel utilisateur
THE FULLY MODERN
OLD SKOOL POWER AMP
+
0222V00000 115VAC/750W
+
0222V00000 115VAC/750W
Welcome to a true throwback—a no-
excuses, Class AB, linear supply, heavy-
as-heck power amplier. But at the same
time, Vidar 2 has an eye to the future,
with full microprocessor management
of all operating conditions, for better
performance and safety. And we’ve even
added a super-smart standby mode that
cuts power consumption to just a watt
or two, while keeping the amp ready for
great sound. We hope you really enjoy
this marriage of old and new!
INTRODUCTION
The following is required by the roughly 9,542
government agencies and regulations we have to
comply with. If you have some common sense, they
should seem pretty straightforward. In any case, read these
instructions before proceeding farther, follow all instructions,
and heed all warnings. Or else!
1. If you don’t know how to install audio devices, get a
qualied professional to help.
2. Never use this device near water, and clean only with a
dry cloth.
3. Assure adequate ventilation, do not block any ventilation
openings, or place near heat sources.
4. Use only the supplied power cord or suitable replacement.
Route cords away from trac areas and protect them from
being pinched. Unplug the cord from the outlet if the apparatus
is unused for a long period of time.
5. To prevent electric shock, do not use the plug with an
extension cord, receptacle, or outlet unless blades can be
fully inserted.
6. Refer all servicing to qualied service personnel. Service is
required when the device has been damaged, including cord or
plug damage, liquid has been spilled or objects have fallen into
the device, the device has been exposed to rain or moisture,
does not operate normally, or has been dropped.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS DEVICE
TO RAIN OR MOISTURE.
STEREO
CONNECTION
1 Connect both left and right speakers.
Connect your right speaker to the right
red and black output terminals and your
left speaker to the left red and black
output terminals.
2 Connect both RCA inputs. Similarly,
connect your source with RCA cables—
right into the input marked “R”, and left
into the input marked “L”.
3 Get powered up. Connect to a wall
socket with the provided AC cord. Or
you can use any IEC-type cord; ours isn’t
special.
4 Turn on when it’s time for the music.
Up is on. Down is off. Pretty simple. Feel
free to leave the amp on all the time
if you’d like. You can always put it in
Standby using the front panel button.
+
0222V00000 115VAC/750W
1
2
3
41
2
1 Connect your speaker to the two top
red terminals only. Right is “+”, and left is
“-”. Please note both of these are active
outputs—do not ground one of them!
3 Connect a balanced source using a
high-quality XLR cable. It’s important that
the preamp is truly balanced for maximum
power output.
4 Get powered up. Connect to a wall
socket with the provided AC cord. Or use
any IEC-type cord; ours isn’t special.
5 Turn on for tunes. Up is on. Down is off.
Pretty simple. Feel free to leave the amp
on all the time if you’d like. You can always
put it in Standby to save power.
MONO
CONNECTION
+
0222V00000 115VAC/750W
1
3
5
2
4
1 Press to toggle Standby mode. When
the amp is in Standby mode, it only uses
a couple of watts, saving power. You can
leave the amp on all the time and just put it
in Standby when you’re not using it
2 When lit, this light indicates Standby
mode. When ashing, it indicates that Vidar
2 is getting everything ready to run.*
3 When lit, this light indicates normal
operation. When ashing, there’s a fault.
See the next section for what to do if it’s
ashing.
*Vidar 2 takes about 30 seconds to perform self-
checks when rst turned on. When coming out of
Standby mode, it takes about 60 seconds.
OPERATION
+
0222V00000 115VAC/750W
1
32
Okay, so you have a ashing light. Deep
breath. We’ll get this taken care of shortly.
When the Vidar 2’s front light ashes during
operation (and the amp mutes), or if it never
stops ashing after you turn on the amp,
there’s a problem, or fault. There are three
kinds of faults:
1. Over-temperature. The heatsinks are too
hot, and Vidar has shut down to protect its
output. If the amp is very hot, turn it off, wait
a while for it to cool down, and try turning
it on again. Please note that in some very
hot ambient environments (over 80 degrees
F), you may need to use an external fan to
avoid over-temperature faults.
2. Over-current. If Vidar is connected to
very low-impedance speakers (2 ohms in
stereo, or 4 ohms in mono), playing very
loud music can cause an over-current condi-
tion. Simply turn the amp off and on again
to clear this fault.
FLASHING LIGHTS
Alternately, Vidar may shut off from over-
current if the speaker cables are shorted. To
troubleshoot this, turn off the amp, discon-
nect the speaker cables from the amp, and
turn it back on again. If it comes back on,
there may be a short in your speaker cables
(or your speakers). Examine your connec-
tions to ensure there are no stray wires or
shorts. Once those have been xed, you
can reconnect the speakers and play music
again.
3. High DC offset. Vidar is a DC-coupled
amp. Its microprocessor monitors DC levels
at the output. However, it may not always
be able to correct for extremely high DC
from your source (such as a preamp). To
clear this fault, turn off the amp, disconnect
the RCA cables or XLR cable from the amp,
and turn it back on again. If the amp turns
on normally, then there may be high DC on
the output of your source. Have the source
inspected and repaired.
WARRANTY
Schiit Audio warrants to the original purchaser that this product shall be free from defects
in material and workmanship for ve (5) years from the date of purchase. If a defect
covered by this warranty occurs during this period, Schiit Audio will repair the defective
product, free of charge. Date of purchase will be based on customer receipts, otherwise
date of manufacturing will be used.
If you believe you need warranty service, contact us rst. Schiit Audio products sent back
to us without a Return Authorization (RA) will be returned to the sender without repair. To
contact us and obtain an RA, email [email protected].
Warranty Limitations. This warranty shall not apply if a product: (a) is modied or tampered
with; (b) is damaged by negligence, accident, unreasonably use, or other causes unrelated
to defective materials or workmanship, or (c) has had the serial number altered or removed.
Any implied warranties, including warranties of merchantability and tness for a particular
purpose, are hereby limited in duration to the warranty period of 5 years. In no event shall
Schiit Audio be liable for consequential or incidental damages resulting from the breach
of any implied or expressed warranties. Some states do not allow these limitations, so
they may not apply to you. You may also have other rights which vary from state to state or
province to province.
SCHIIT.COM
IN THE BOX
(1) Vidar 2
(1) Power Cord
(0) Class D modules
(0) Switching supplies
(Various) Stickers and stuff
(Innite) Appreciation from the
whole Schiit crew in Valencia, CA
and Corpus Christi, TX
(Even more) Thanks from our
chassis and PCB guys in
California, Nevada, and Utah.
This product is in compliance with standards
and regulations of the European Community.
Autres manuels Schiit Accessoires pour amplificateurs
Manuels Accessoires pour amplificateurs populaires d'autres marques
Crown
Crown Com-Tech CT-1610 Manuel utilisateur
powersoft
powersoft DSP LITE Manuel utilisateur
Musical Concepts
Musical Concepts PA-7 Manuel utilisateur
QSC
QSC SF-1 Manuel utilisateur
Kessler Engineering
Kessler Engineering TL-922 Revival (tm) Manuel utilisateur
GAI-Tronics
GAI-Tronics 12565-001 Manuel d'utilisation
