Schacht TABLE LOOM Manuel utilisateur

TABLE LOOM

Assembly InstructIons

Find out more at schachtspindle.com

Schacht Spindle Company 6101 Ben Place Boulder, CO 80301

p. 303.442.3212 800.228.2553 f. 303.447.9273

– 2 –

PARTS

1 - Base assembly

1 - Castle assembly

1 - Beater assembly

1 - Reed

2 - Castle braces

2 - Lease sticks

3 - Apron bars

Heddle bar hooks (for 25" looms only)

8 for 4-Shaft (4S) or 16 for 8-Shaft (8S)

Heddle bars: 8 for 4-Shaft or 16 for 8-Shaft

Heddles:

4-Shaft: 15" & 20" – 300; 25" –400

8-Shaft: 15" –300; 20"–400; 25" –500

4 - #8 x 1½" Trusshead screws (for 8S

only)

1. Unpack the table loom and remove

all of the packing material and tape.

Locate the small plastic bag which

contains the hardware and the apron

cords for your loom (see parts list).

2. On 8-shaft looms only, the cross

brace is only partially secured for

shipping purposes. Remove the

screws (A) on each side and discard.

Raise the cross brace up and screw

into both A & B with the four

1½" trusshead screws.

3. Loosely secure the castle

braces to the rear legs with

3" trusshead machine screws

and barrel nuts. Place the

castle upright between the

sides of the loom frame

and secure it, threading the

1-1/8" trusshead screws

through each loom side into

the inserts on the inside of

the castle side (2 per side on

the 4S, 4 on the 8S). Secure

the castle brace to the castle

side in the same manner (D)

(1 screw per side on the 4S,

Shaft Lever Shaft Lever Cord

Castle Side

Rear Leg

Castle Brace

Loom Side

A&B

Rubber Pad Cross Brace

FIGURE 1: ASSEMBLED 4-SHAFT LOOM

4 - Rubber bumpers

2 - Barrel nuts

¼ x 1-1/8" Trusshead machine screws (6

for 4S or 12 for 8S)

2 - ¼ x 3" Trusshead machine screws

Apron cords: 15"–6; 20" –8; 25" –10

– 3 –

FIGURE 3: SHAFTS / HEDDLES

Slots in

Frame

Heddles

Heddle Bars

Shaft Frame

Heddle Bar

Hooks

Apron Cord Apron Bar

Beam

Apron Cord

FIGURE 2: APRON CORDS

and 2 on the 8S). Tighten the screw at

the rear of the castle brace.

4. Peel the backing off the rubber

bumpers and press them into the

indentations in the bottom of the legs.

5. Attach the apron bars. Locate the

pre-cut looped apron cords (one cord

for each hole in the cloth and warp

beams). Take one cord and insert one

end a few inches through a hole in the

beam. Now take the other end of the

cord and put it through the second

loop in from the short end that you

put through the beam. Pull rmly on

the cord to tighten it around the beam

(see Fig. 2A). Repeat this procedure

across each of the beams. To attach

the apron bar to the apron cords,

start at one end of the beam with the

outermost cord and work across. Fold

the end of the looped cord at about 4"

from the end and insert this doubled

cord through the second loop from

the end of the cord (see Fig. 2B).

Slide the apron bar through the loop

formed by the doubled over cord at

point X. Pull the cord tight. Repeat

across the entire beam.

6. Untie the shaft lever cords and

remove the shafts from the bottom of

the castle. Lay two heddle bars on a

at surface. Count out the heddles for

the rst shaft, and carefully transfer

them in a single bunch from the hold-

ing bar or cord to the heddle bars.

Place the heddle bars in the shaft.

First t one end of the heddle bar

into the slot on one side of the shaft.

Then bend the heddle bar slightly and

t the other end into the slot on the

other side of the shaft. For 25" looms

there are wire heddle bar hooks (2

– 4 –

per shaft) to support the heddle bars.

Slip the hooks through the holes near

the center of the top and bottom shaft

frame. Bend the heddle bar slightly to

snap it into the hook.

7. Insert the shafts back into the

castle from the bottom of the castle.

Put the shaft levers in the up posi-

tion. Attach the shaft lever cords to

the levers (see Figure 4). Note: you

can determine which lever you want

tied up to the rst shaft (i.e. the right

side or the left side) at this time. On

4 shaft looms the cords from the rst

and second shafts go over the front

small dowel in the top of the castle

behind the levers. The cords from the

third and fourth shafts go over the

rear small dowel. Similarly on 8 shaft

looms the rst and second cords go

over the front dowel, the third and

fourth go over the second dowel, the

fth and sixth go over the third dowel,

and the seventh and eighth go over

the rear dowel. Adjust the shafts to

a height of 5¼" below the top of the

castle. This measurement is from the

top of the harness side to the top of

the castle (see Figure 5).

Note: The correct position for an ac-

tive lever is pointing toward you. If

you pull the lever down too far it will

interfere with the operation of the

beater.

8. Place the beater assembly onto the

bolts that are screwed to the inside of

the loom base. The wing nuts on the

beater should be facing forward. To

insert the reed into the beater, loosen

the two wing nuts and raise the top

of the beater, place the reed centered

in the slot, slide the top of the beater

down and secure the wingnuts.•

FIGURE 5: SHAFTS/CASTLE

5 ¼”

Castle

Shaft

FIGURE 4: LEVERS

Lever Cord

Lever Front

Dowel

Rear Dowel

Autres manuels Schacht Tissage

Schacht

Schacht FL3053 Manuel utilisateur

Schacht

Schacht Wolf Pup Manuel utilisateur

Schacht

Schacht TL1105 Manuel utilisateur

Schacht

Schacht MIGHTY WOLF FL3002E Manuel utilisateur

Schacht

Schacht CRICKET LOOM Manuel utilisateur

Schacht

Schacht WOLF PUP & PUP LT Manuel utilisateur

Schacht

Schacht SL2225 Manuel utilisateur

Schacht

Schacht WOLF PUP 8.10 STROLLER Manuel utilisateur

Schacht

Schacht FLATIRON BULKY PLYER FLYER HEAD Guide de démarrage rapide

Schacht

Schacht BABY WOLF FL3001E Manuel utilisateur

Schacht

Schacht Wolf Pup Manuel utilisateur

Schacht

Schacht FL3109 Manuel utilisateur

Schacht

Schacht Wolf Pup Manuel utilisateur

Schacht

Schacht CRANBROOK LOOM Manuel utilisateur

Schacht

Schacht WOLF PUP 8.10 LOOM Manuel utilisateur

Schacht

Schacht Wolf Pup 8.10 Manuel utilisateur

Schacht

Schacht WOLF PUP 8.10 HEIGHT EXTENDER Manuel utilisateur

Schacht

Schacht BABY WOLF FL3001 Manuel utilisateur

Schacht

Schacht Wolf Pup Guide d'installation

Schacht

Schacht CRICKET QUARTET Manuel utilisateur

Schacht

Schacht WOLF SECTIONAL BEAM Manuel utilisateur

Schacht

Schacht CRANBROOK Manuel utilisateur

Schacht

Schacht CRICKET QUARTET SL2045-05 Manuel utilisateur

Schacht

Schacht TL1105 Manuel utilisateur

Manuels Tissage populaires d'autres marques

Ashford

Ashford RIGID HEDDLE LOOM Manuel utilisateur

AVL Looms

AVL Looms Dobby V Series Manuel utilisateur

ROJ

ROJ SUPER ELF S3 Manuel utilisateur

Louet

Louet Spring Manuel utilisateur

Toyota

Toyota JAT810 Manuel utilisateur

Toika

Toika JAANA Manuel utilisateur

Leclerc Looms

Leclerc Looms COMPACT 4 SHAFTS Manuel utilisateur

Leclerc Looms

Leclerc Looms VOYAGEUR Manuel utilisateur

Toyota

Toyota JAT710 Manuel utilisateur

Ashford

Ashford Katie Table Loom Manuel utilisateur

Louet

Louet Jane Instructions de montage

Toyota

Toyota JAT810 Manuel utilisateur

Ashford

Ashford WARPING FRAME - Large Manuel utilisateur

Ashford

Ashford KIWI Manuel utilisateur

Toika

Toika LAILA Manuel utilisateur

Louet

Louet Delta Manuel utilisateur

Leclerc Looms

Leclerc Looms COMPACT 8 SHAFTS Manuel utilisateur

Louet

Louet David-III Instructions de montage