Saxby Lighting Nova Manuel

• TheLEDmoduleinthisproductisnonreplaceable

Instructionleaflet

Nova Emergency Exit Light

54544

www.saxbylighting.com

Foryoursafety,alwaysswitchoffthesupplybeforecleaning.

Wasteelectricalproductsshouldnotbedisposedofwithhouseholdwaste.Pleaserecyclewherefacilities

exist.CheckwithyourLocalAuthorityorretailerforrecyclingadvice.

Recycling advice

Safety information

SaxbyLighting.BH233PE

Werecommendcleaningwithasoftdrycloth.

Donotusesolventsorabrasivecleanersasthesecould

damagethefinish.

Fitting/replacing bulbs

Iss.114072015

• Connectthebattery,ensuringthecorrectpolarityis

observed.

• Refittheproducttothetopcoverremovedearlier.

• Replacefuseorcircuitbreakerandswitchon.Your

lightisnowreadyforuse.

Commissioning

Care and cleaning

• Thebatterytestbuttonislocatedonthewhiteceiling

cover.Pushtotesttheemergencyfunctionofthe

product.

• Testscanbecarriedoutasandwhenrequired.

• WhentheLEDlightnexttothetestbuttonis

illuminated,thisindicatesthattheunitischarging

Product testing

Thankyouforpurchasingthislightfitting.Pleasereadtheinstructionscarefullybeforeusetoensuresafeand

satisfactoryoperationofthisproduct.Pleaseretaintheseinstructionsforfuturereference.

Warning

This light fitting is Class 2 (Double

Insulated) and must not be connected to an

Earth circuit.

Pleasereadtheseinstructionscarefullybefore

commencinganywork.

Thisunitmustbefittedbyacompetentandqualified

electrician.

InstallinaccordancewithIEEWiringregulationsand

currentBuildingRegulations.

Topreventelectrocutionswitchoffatmainssupply

beforeinstallingormaintainingthisfitting.Ensure

otherpersonscannotrestoretheelectricalsupply

withoutyourknowledge.Ifyouareinanydoubt,

pleaseconsultaqualifiedelectrician.

Thislightfittingshouldbeconnectedtoafusedcircuit.

Ifreplacinganexistingfitting,makeacarefulnoteof

theconnections.

Thissystemcontainsnon-replaceablepartsand

cannotbeserviced.Ifdamageoccursthepartshould

bescrapped.

Wasteelectricalproductsshouldnotbedisposedof

withhouseholdwaste.Pleaserecyclewherefacilities

exist.Checkwithyourlocalauthorityorretailerfor

recyclingadvice.

ThisproductisratedatIP20.

Thisproductisnotsuitablefordimming.

Layout

• Themainssupplycablemusthaveaminimumcross

sectionalareaof1.0mm²

Existingfittingsmustbecompletelyremovedbefore

installationofanewproduct.Beforeremovingthe

existingfitting,carefully note the position of each set

of wires.

• Removethetopcoverbypushingintheretaining

clipswithaflatheadscrewdriver(Fig.1)

• Usingthetopcoverasatemplate,markthelocation

ofthefixingholes.Drillholesandfitsuppliedwall

plugs(suitableformasonryonly-forothersurfaces

useappropriatefixings).Fixproducttothewallusing

thesuppliedscrews.Takecaretoavoiddamaging

anyconcealedwiringandpipes.

• Feedtheincomingsupplycablethroughthecable

entryhole.

• Wireasdetailedbelow.

Installation

Wiring

Thisproductcanbewiredindifferentways,depending

onwhethernonmaintained/maintained/switched

maintainedwiringisrequired.

ToconfiguretheproductasaNon-maintainedfitting,

thesuppliedjumperloopmustberemovedandthelive

supplywiremustbeconnectedtooneofthepermanent

liveterminalsandtheneutralsupplywiretotheterminal

markedN.

1)Toconfiguretheproductasamaintainedfitting,

connectthesuppliedjumperloopbetweentheLandL

terminals.

2)Ifthemaintainedmodeneedstobeswitchablethen

thejumperisnotneededandaswitchedlivesupplywire

willneedtobeconnectedtotheLsterminalinstead.

Check that...

• Youhavecorrectlyidentifiedthewires.

• Theconnectionsaretight.

• Noloosestrandshavebeenleftoutoftheconnection

block.

Specification

Voltage : 240V~50Hz

Lamp : 2WLEDModule(SMD28

  35)CoolWhite-46lm

IPrating : 20

Lumens : 50lminEMmode

Duration : 3hours(180minutes)

OperatingTemperature : 5˚Cto50˚C

MaximumOperatingHumidity: 10%-90%

ChangeoverTime : Approximately1s

BatterySpecification : 4.8V600mAhNi-Cad

BatteryChargeTime : 24hours

Fig. 1

LLNLs

Permanent

Live

Brown

Neutral

Blue

Switched

Live

Ce manuel convient aux modèles suivants

Autres manuels Saxby Lighting Équipements de sécurité

Saxby Lighting

Saxby Lighting Sight Plus 94346 Manuel utilisateur

Manuels Équipements de sécurité populaires d'autres marques

Innova

Innova Xtirpa Mode d’emploi

bolle SAFETY

bolle SAFETY B810 Manuel utilisateur

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Manuel utilisateur

Hiltron security

Hiltron security POWER8E Mode d’emploi

Hatco

Hatco B-950P Manuel utilisateur

Sitec

Sitec TX MATIC Manuel utilisateur

TEUFELBERGER

TEUFELBERGER GRIP 12 Manuel utilisateur

MSA

MSA PremAire System Manuel utilisateur

AMC

AMC 1022M Series Manuel utilisateur

Trinity

Trinity CASS S3 Manuel utilisateur

CMC

CMC Helitack HotSeat Manuel utilisateur

Force

Force P-35 Manuel utilisateur

ACM

ACM SAFETY D200 Manuel du produit

Honeywell

Honeywell Miller H-Design DuraFlex Manuel de l'opérateur

ROCK

ROCK P-451 AS Manuel utilisateur

Power first

Power first 2XYR7A Manuel de service

SCHUBERTH

SCHUBERTH SHP 28-C Manuel utilisateur

Trango

Trango CINCH Manuel utilisateur