SawStop JSS Manuel

Service Procedure SP-JSS-190516-001

Steps to Replace Job Site Saw Arbor Belt or Motor

Page 1 of 10

Tools & Supplies Required for This Procedure:

•#2 Phillips Head Screwdriver

•5mm Allen Wrench

•13mm Wrench

•Blade Wrench

•SawStop Part #JSS-238

Procedure Steps:

(Before starting, please read instructions all the way through to ensure complete understanding)

To ensure safety, disconnect all electrical power to the saw.

1. Tilt the saw to 45 degrees.

Page 2 of 10

2. Lower the blade completely and remove the fence from the saw and set aside.

3. Use a 5mm Allen wrench and a 13mm wrench to loosen and remove the four bolts that attach

the saw to the cart and set aside.

Service Procedure

Steps to Replace Job Site Saw Arbor Belt or Motor

Page 3 of 10

4. Lift saw off of the cart and place upside down on a soft sturdy surface.

5. There are 15 Phillips head screws around the outer edge of the bottom that attach it to the saw

body. Starting with the screw to the left of the counter spring indentation at the back and

working counter clockwise, remove all 15 and the bottom and set aside.

•NOTE: When the last screw is removed, the bottom will spring upward a bit.

Service Procedure

Steps to Replace Job Site Saw Arbor Belt or Motor

Page 4 of 10

6. Remove the motor housing bolt that is directly above the motor power cord and set aside.

7. Remove the four bolts that fasten the motor to the elevation carriage assembly.

Service Procedure

Steps to Replace Job Site Saw Arbor Belt or Motor

Page 5 of 10

8. Turn the motor so it is oriented as shown below. On the left side of the arbor wrench you will

notice a small hole near the end. Finger-tighten the arbor wrench to the motor plate as shown

below with the M5x50mm bolt that was provided with your belt.

9. Re-install one bolt from step 7 through the motor plate into the bottom left motor mounting hole

as shown below. (This will create a pivot point for the motor)

Service Procedure

Steps to Replace Job Site Saw Arbor Belt or Motor

Page 6 of 10

10. Put the new belt on both the motor and the arbor pulleys.

11. Pull on the wrench to apply tension to the belt and to align the motor mounting bolt holes.

Service Procedure

Steps to Replace Job Site Saw Arbor Belt or Motor

Service Procedure

Steps to Replace Job Site Saw Arbor Belt or Motor

Page 7 of 10

12. Reinstall the remaining three motor mounting bolts using a 5mm Allen wrench.

13. Remove the bolt and wrench.

Page 8 of 10

14. Reinstall the motor housing bolt using a Phillips head screwdriver.

15. Tilt the saw back to 90 degrees. Above the motor is the counter balance spring that must be in

the up position leaning against the trunnion.

Service Procedure

Steps to Replace Job Site Saw Arbor Belt or Motor

Page 9 of 10

16. There is a small groove on the bottom of the indentation that the top of the counter balance

spring must seat in. You’ll want to “hover” the base over the saw and slowly lower it until the

two match up.

Service Procedure

Steps to Replace Job Site Saw Arbor Belt or Motor

Service Procedure

Steps to Replace Job Site Saw Arbor Belt or Motor

Page 10 of 10

17. Reinstall the 15 screws starting with the one that is left of the indentation.

NOTE: When using a power screw driver, the torque must be set about midrange or you

WILL strip them.

18. Place the saw back on the cart and reinstall the four 5mm bolts and nuts.

Questions?

Contact the SawStop Customer Support Center with any questions or

suggestions:

Call: (503) 582-9934

Email: [email protected]

Autres manuels pour JSS

2

Table des matières

Autres manuels SawStop Scie

SawStop

SawStop CB31230 Manuel utilisateur

SawStop

SawStop CTS-015 Manuel utilisateur

SawStop

SawStop MC-CNS Manuel utilisateur

SawStop

SawStop CB31230 Manuel utilisateur

SawStop

SawStop CNS175 Manuel utilisateur

SawStop

SawStop T-Glide Manuel utilisateur

SawStop

SawStop JSS-MCA Manuel utilisateur

SawStop

SawStop T-Glide Fence System Manuel utilisateur

SawStop

SawStop JOBSITE SAW PRO Manuel utilisateur

SawStop

SawStop T-Glide TGP2-FA Mode d’emploi

SawStop

SawStop CTS-120A60 Manuel utilisateur

SawStop

SawStop PCS31230 Manuel utilisateur

SawStop

SawStop Jobsite Saw Manuel utilisateur

SawStop

SawStop JSS Manuel

SawStop

SawStop PCS175 Manuel utilisateur

SawStop

SawStop 10” Manuel utilisateur

SawStop

SawStop ICS31240-50 Manuel utilisateur

SawStop

SawStop ICS31230 Manuel utilisateur

SawStop

SawStop JSS Manuel utilisateur

SawStop

SawStop RT-LFT Manuel utilisateur

SawStop

SawStop JSS-120A60 Manuel utilisateur

SawStop

SawStop MB-CNS-000 Manuel utilisateur

SawStop

SawStop TGA-GA48 Manuel utilisateur

SawStop

SawStop CTS-120A60A Manuel utilisateur

Manuels Scie populaires d'autres marques

RIDGID

RIDGID BS1400 Manuel utilisateur

ATIKA

ATIKA BWS 400-2 Manuel utilisateur

RGC

RGC FS20 Manuel utilisateur

Makita

Makita M2300 Manuel utilisateur

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manuel utilisateur

IMET Spa

IMET Spa SIRIO 370 AF-E Manuel utilisateur

Optimum

Optimum OPTisaw CS 275 Manuel utilisateur

Makita

Makita BPB180 Manuel utilisateur

Stihl

Stihl MS 462 C-M Manuel utilisateur

AEG

AEG TS 250 K Manuel utilisateur

Meec tools

Meec tools 004665 Manuel utilisateur

Makita

Makita LS1018L Manuel utilisateur

Ryobi

Ryobi RCS1400 Manuel utilisateur

DeWalt

DeWalt DCS391 Manuel utilisateur

Sealey

Sealey SA72 Manuel utilisateur

skilsaw

skilsaw SPT88 Instructions de montage

Urrea

Urrea SI810 Dimensions et guide d'installation

EINHELL

EINHELL BKG 210/1 Manuel utilisateur