SawStop JSS Manuel

Service

Procedure SP-JSS-190522-001

Adjusting JSS Guard Clamp

Page 1 of 2

Tools & Supplies Required for This Procedure:

•4mm Allen wrench

•13mm combination wrench

Background: It sometimes becomes necessary to adjust the alignment of the JSS guard clamp to the

blade, or to adjust the clamping force. The clamp works on the same principles at the other SawStop

saws; the red clamping handle operates a cam that pushes the pressure plate sideways to clamp the

riving knife or splitter into place. This procedure discusses the steps needed to align the splitter with the

saw blade, and to adjust the clamping force.

Procedure Steps:

(Before starting, please read instructions all the way through to ensure complete understanding)

(Table Layout: Sample Text follows)

Guard Clamp Alignment Screws:

Adjusting these screws moves the position of the guard

clamp in and out to align with the saw blade.

Checking alignment:

1. Slide the steel straightedge against the left side of the

blade plate, making sure it runs between the carbide

tips and rides flat against the blade with no air gaps.

2. Ideally, the straightedge should also run flat against

the left side of the riving knife, with no gaps. If so,

you’re done – no alignment is needed.

Service

Procedure SP-JSS-190522-001

Adjusting JSS Guard Clamp

Page 2 of 2

Adjusting alignment:

Adjusting clamping force:

If adjustment is needed:

1. Using a 4mm Allen wrench screwdriver, adjust the

position of the guard clamp left or right to bring it into

alignment with the splitter or riving knife.

2. It’s best to turn each screw the same amount to begin

with to move the whole clamp left or right.

3. If the splitter is at a different angle than the blade,

adjust the screws individually as needed to make the

riving knife parallel to the blade.

1. For adjustment, the clamp needs to be in the up/open

position, so that the cam is not engaged.

2. Push the pressure plate inward; this will expose the

head of the clamping bolt.

3. To adjust clamping force, use a 13mm wrench to turn

the bolt head while it is exposed:

a. To increase force, turn the bolt head clockwise

b. To decrease force, turn the bolt head

counterclockwise

c. To avoid damaging the clamp from

excessive force, adjust in SMALL

increments (1 or at most 2 detents.)

Questions?

Contact the SawStop Customer Support Center with any questions or

suggestions:

Call: (503) 582-9934

Email: [email protected]

Autres manuels pour JSS

2

Table des matières

Autres manuels SawStop Scie

SawStop

SawStop JSS Manuel utilisateur

SawStop

SawStop CTS-120A60 Manuel utilisateur

SawStop

SawStop CB31230 Manuel utilisateur

SawStop

SawStop CTS-015 Manuel utilisateur

SawStop

SawStop T-Glide TGP2-FA Mode d’emploi

SawStop

SawStop CB31230 Manuel utilisateur

SawStop

SawStop JSS-120A60 Manuel utilisateur

SawStop

SawStop PCS175 Manuel utilisateur

SawStop

SawStop JSS-MCA Manuel utilisateur

SawStop

SawStop RT-LFT Manuel utilisateur

SawStop

SawStop TGA-GA48 Manuel utilisateur

SawStop

SawStop PCS31230 Manuel utilisateur

SawStop

SawStop T-Glide Fence System Manuel utilisateur

SawStop

SawStop T-Glide Manuel utilisateur

SawStop

SawStop MB-CNS-000 Manuel utilisateur

SawStop

SawStop Jobsite Saw Manuel utilisateur

SawStop

SawStop JSS Manuel

SawStop

SawStop 10” Manuel utilisateur

SawStop

SawStop CNS175 Manuel utilisateur

SawStop

SawStop CNS-SFA Manuel utilisateur

SawStop

SawStop ICS31230 Manuel utilisateur

SawStop

SawStop CTS-120A60A Manuel utilisateur

SawStop

SawStop ICS31240-50 Manuel utilisateur

SawStop

SawStop JOBSITE SAW PRO Manuel utilisateur

Manuels Scie populaires d'autres marques

RIDGID

RIDGID BS1400 Manuel utilisateur

ATIKA

ATIKA BWS 400-2 Manuel utilisateur

RGC

RGC FS20 Manuel utilisateur

Makita

Makita M2300 Manuel utilisateur

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manuel utilisateur

IMET Spa

IMET Spa SIRIO 370 AF-E Manuel utilisateur

Optimum

Optimum OPTisaw CS 275 Manuel utilisateur

Makita

Makita BPB180 Manuel utilisateur

Stihl

Stihl MS 462 C-M Manuel utilisateur

AEG

AEG TS 250 K Manuel utilisateur

Meec tools

Meec tools 004665 Manuel utilisateur

Makita

Makita LS1018L Manuel utilisateur

Ryobi

Ryobi RCS1400 Manuel utilisateur

DeWalt

DeWalt DCS391 Manuel utilisateur

Sealey

Sealey SA72 Manuel utilisateur

skilsaw

skilsaw SPT88 Instructions de montage

Urrea

Urrea SI810 Dimensions et guide d'installation

EINHELL

EINHELL BKG 210/1 Manuel utilisateur