Sauder 413045 Manuel utilisateur
PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
English.................... Page 1-18
Français...............Pages 19-21
Espanol.............Páginas 22-24
Lot #: 352976 05 / 08 / 13
Date Purchased: ____________________
413045
TV Stand
ASSEMBLY TOOLS REQUIRED
Hammer
Tip Shown Actual Size
No. 2 Phillips Screwdriver
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .............4
Assembly Steps....................5-18
Français..............................19-21
Espanol...............................22-24
Safety .................................25-26
Warranty...................................27
14-1/4"
41-1/2"
95 lbs.
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury
or death. ATV that is too large for the available space might be accidentally pushed or bumped off the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 95 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
Page 2 www.sauder.com/services 413045
PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A RIGHT END 1
B LEFT END 1
C LARGE UPRIGHT 1
D SMALL UPRIGHT 1
E TOP 1
F BOTTOM 2
G SHELF 1
H ADJUSTABLE SHELF 2
I BACK 1
J RIGHT DRAWER FRONT 1
K LEFT DRAWER FRONT 1
D69 DRAWER BACK 2
D40 RIGHT DRAWER SIDE 2
D41 LEFT DRAWER SIDE 2
D967 DRAWER BOTTOM 2
P SKIRT 1
Q STOP MOLDING 1
Page 3
www.sauder.com/services413045
A
B
C
D
E
F
G
H
I
J
K
D69 D40
D41
P
Q
H
F
D69 D40
D41
D967
D967
HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com/services 413045
35DA CABINET RIGHT - 2 35DD DRAWER LEFT - 2
35DC DRAWER RIGHT - 2
35DB CABINET LEFT - 2
WARNING LABEL - 1
BB
(Refer to the last step for proper location and application)
ANGLE BRACKET - 6
U
BROWN 7/16" LARGE HEAD SCREW - 16
FF
BLACK 1-7/8" FLAT HEAD SCREW - 12
CC
HIDDEN CAM - 12
R2
RUBBER SLEEVE - 8
AA
SCREW COVER - 8
Y
GOLD 5/16" FLAT HEAD SCREW - 16
GG
METAL PIN - 12
Z
CAM SCREW - 4
T2
CAM DOWEL - 8
S2
NAIL - 42
HH
DRAWER FRONT BRACKET - 2
VPULL - 2
WFOOT - 1
X
EE SILVER 3/4” MACHINE SCREW - 4
BLACK 1-9/16" FLAT HEAD SCREW - 8
DD
1
1
S
t
e
p
Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push twelve HIDDEN CAMS (R2) into the ENDS (A and B), UPRIGHTS (C and D), and TOP (E). Then, insert the metal end of a
eight CAM DOWELS (S2) into the HIDDEN CAMS in the ENDS and UPRIGHTS.
Page 5
www.sauder.com/services413045
Do not tighten the HIDDEN CAMS in this step.
(8 used)
(12 used)
A
B
C
D
E
Arrow
Hole
Do not insert CAM
DOWELS into this part.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Arrow
S2
R2
Arrow
R2
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1192
to watch a video on how to assemble your unit.
Turn four CAM SCREWS (T2) into the STOP MOLDING (Q).
Fasten the STOP MOLDING (Q) to the TOP (E). Tighten four HIDDEN CAMS.
Page 6 www.sauder.com/services 413045
2
2
S
t
e
p
Q
Q
E
Surface with
HIDDEN CAMS
If the STOP MOLDING (Q) has an unfinished
surface, it should be positioned here.
T2
Fasten the CABINET RIGHTS (35DA) and CABINET LEFTS (35DB) to the ENDS (A and B) and SMALL UPRIGHT (D). Use
eight GOLD 5/16" FLAT HEAD SCREWS (GG).
Page 7
www.sauder.com/services413045
3
3
S
t
e
p
35DA
35DA
35DB
35DB
GOLD 5/16” FLAT HEAD SCREW
(8 used in this step)
GG
Roller end
Roller end
A
B
D
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Finished edge
Finished edge
Surface with
HIDDEN CAMS
Roller end
35DA
35DA
35DB
35DB
Finished edge
Fasten the LARGE UPRIGHT (C) to the TOP (E). Tighten two HIDDEN CAMS.
Page 8 www.sauder.com/services 413045
4
4
S
t
e
p
Q
E
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
C
Finished edge
Caution
Risk of damage or
injury. Hidden Cams
must be completely
tightened. Hidden
Cams that are not
completely tightened
may loosen, and parts
may separate.
To completely tighten:
Start Tighten
Arrow
Maximum
210 degrees
Minimum
190 degrees
Arrow
Page 9
www.sauder.com/services413045
5
5
S
t
e
p
Fasten the SHELF (G) to the LARGE UPRIGHT (C). Use two BLACK 1-7/8" FLAT HEAD SCREWS (CC).
Fasten the SMALL UPRIGHT (D) to the SHELF (G). Tighten two HIDDEN CAMS.
C
DG
BLACK 1-7/8" FLAT HEAD SCREW
(2 used in this step)
CC
Surface with
HIDDEN CAMS
Finished edge
If the SHELF (G) has
an unfinished surface, it
should be positioned here.
Maximum
210 degrees
Minimum
190 degrees
Arrow
Fasten the BOTTOMS (F) to the SMALL UPRIGHT (D). Use two BLACK 1-7/8" FLAT HEAD SCREWS (CC).
Insert four METAL PINS (Z) into the BOTTOMS (F).
Page 10 www.sauder.com/services 413045
6
6
S
t
e
p
D
F
F
Surface with
more holes
Surface with
more holes
BLACK 1-7/8" FLAT HEAD SCREW
(2 used in this step)
CC
These holes
must be here.
Z
(4 used)
Table des matières
Autres manuels Sauder Support et étagère
Sauder
Sauder Palladia 411864 Manuel utilisateur
Sauder
Sauder Studio Edge 412067 Manuel utilisateur
Sauder
Sauder Rustic Country 412373 Manuel utilisateur
Sauder
Sauder Entertainment Credenza Manuel utilisateur
Sauder
Sauder Studio 408559 Manuel utilisateur
Sauder
Sauder Harvey Park 421982 Manuel utilisateur
Sauder
Sauder 423088 Manuel utilisateur
Sauder
Sauder New Prairie 08 Manuel utilisateur
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
