Satel Integra Series Manuel utilisateur

Connecting to

BT Redcare Secure Mk3

MANUAL

SATEL sp. z o.o.

ul. Budowlanych 66

80-298 Gdańsk

POLAND

tel. + 48 58 320 94 00

www.satel.eu

redcare_i_en 05/19

Alarm Control Panels

WARNINGS

The security alarm system should be installed by qualified personnel.

Prior to installation, please read carefully this manual in order to avoid mistakes that can lead

to malfunction or even damage to the equipment.

Disconnect power before making any electrical connections.

Changes, modifications or repairs not authorised by the manufacturer shall void your rights

under the warranty.

SATEL's goal is to continually upgrade the quality of its products, which may result in some

changes of their technical specifications and firmware. The current information on

the introduced modifications is available on our website.

Please visit us:

http://www.satel.eu

The declaration of conformity may be consulted at www.satel.eu/ce

The following symbols may be used in this manual:

- note;

- caution.

SATEL 1

CONTENTS

1. General.............................................................................................................................2

2. System installation............................................................................................................2

2.1 Cabling ......................................................................................................................2

2.2 Connection of BT Redcare Secure Mk3 unit .............................................................2

3. System programming........................................................................................................ 3

3.1 Programming communication with BT Redcare Secure Mk3 unit..............................3

SATEL 2

1. General

This manual applies to the control panels of the INTEGRA and INTEGRA Plus series:

– INTEGRA 24

– INTEGRA 32

– INTEGRA 64

– INTEGRA 128

– INTEGRA 64 Plus

– INTEGRA 128 Plus

– INTEGRA 256 Plus

This manual assumes that the dial capture board is already fitted inside the BT Redcare

Secure Mk3 unit.

AUX or another high current output can be used instead of OUT2 in step 2.2.2 if you prefer.

The Redcare terminals marked PANEL A and PANEL B are not polarity conscious.

The dial capture board will auto detect the events as they are sent from the INTEGRA panel.

The Redcare unit takes up to 5 minutes to boot, so the installer must wait before it is online.

2. System installation

Disconnect power before making any electrical connections.

The following tools will be useful during installation:

slotted screwdriver 2.5 mm,

Phillips screwdriver,

side cutters.

2.1 Cabling

It is recommended that unscreened straight-through cable be used for making electric

connections between devices included in the system (using twisted-pair cable, e.g. UTP,

STP, FTP, is not advisable).

2.2 Connection of BT Redcare Secure Mk3 unit

The control panel mainboard contains electronic components sensitive to

electric charges.

You must complete all wiring, connections and device installations before

connecting the battery or applying AC mains to the control panel.

1. Connect the “TIP” and “RING” telephone line input terminals from the INTEGRA panel to

the terminals marked “Panel A” and “Panel B” on the Secure MK3 unit.

2. Connect the “OUT2” high-current programmable output terminal from the INTEGRA panel

to the terminal marked “PWR+” on the Secure MK3 unit.

3. Connect the “COM” common ground terminal adjacent to the “OUT2” terminal from the

INTEGRA panel to the terminal marked “0V” on the Secure MK3 unit.

SATEL 3

Fig. 1. The way to connect BT Redcare Secure Mk3 to an INTEGRA panel.

I – Dial capture module connected to PSTN dialer.

II – High current output connected to Redcare power input.

3. System programming

Connect your computer to an INTEGRA panel for programming using:

DLOADX software (available from Satel website)

PC computer running Windows

USB-RS programming cable

3.1 Programming communication with BT Redcare Secure Mk3 unit

1. Navigate to “Data →Reporting →Monitoring stations” in DLOADX.

2. Click the tick box next to “Reporting – TELEPHONE”.

3. Select “Station 1 only”.

4. Select “Reporting Format: Contact ID (full)”.

5. Enter “29” in “Tel. Number”.

6. Enter the last 4 digits of the Redcare TAID as the identifier. Enter this in both “Identifiers

1” and “Identifiers Sys.”.

7. Navigate to “Data →Outputs”.

8. Program the Output 2 function to “41: Power supply”.

9. Write the changes to the panel.

SATEL 4

Fig. 2. Example of Reporting settings.

SATEL 5

Fig. 3. Example of Outputs settings.

Autres manuels pour Integra Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Satel Panneau de contrôle

Satel

Satel CSP-208 Instructions de montage

Satel

Satel INTEGRA Plus Manuel du propriétaire

Satel

Satel CA-5 Manuel utilisateur

Satel

Satel CA-10 Guide de l'utilisateur

Satel

Satel Integra Plus Series Guide de l'utilisateur

Satel

Satel Integra 24 Manuel utilisateur

Satel

Satel Versa Manuel utilisateur

Satel

Satel CA-6 KLED-S Manuel du propriétaire

Satel

Satel Versa Manuel utilisateur

Satel

Satel Versa Plus Manuel du propriétaire

Satel

Satel VERSA Plus LTE Mode d'emploi

Satel

Satel PERFECTA Manuel utilisateur

Satel

Satel PERFECTA-IP-32 Guide de l'utilisateur

Satel

Satel ACSP-402 Manuel utilisateur

Satel

Satel PERFECTA-T Guide de l'utilisateur

Satel

Satel VERSA Series Manuel du propriétaire

Satel

Satel Integra 128-WRL Guide de l'utilisateur

Satel

Satel CA-5 Manuel utilisateur

Satel

Satel Integra 128-WRL Guide de l'utilisateur

Satel

Satel Integra Series Guide de l'utilisateur

Satel

Satel Versa Manuel utilisateur

Satel

Satel Versa Seris Guide de l'utilisateur

Satel

Satel ACCO-NT Guide de l'utilisateur

Satel

Satel CA-64 PTSA Manuel utilisateur

Manuels Panneau de contrôle populaires d'autres marques

RDZ

RDZ PC-HRX Manuel utilisateur

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuel technique

Efka

Efka Variocontrol V810 Manuel utilisateur

Cebora

Cebora 208-10 Manuel utilisateur

AMX

AMX AutoPatch CP-15 Manuel utilisateur

Evolution

Evolution IQ plus 800 Manuel utilisateur

Fagor

Fagor 8040 TCO CNC Manuel utilisateur

Trane

Trane ComfortLink II XL950 Control Manuel utilisateur

AKO

AKO PROCool AKO-17635-2 Manuel utilisateur

ABB

ABB 6136/30M-101 Manuel utilisateur

Telikou

Telikou BK-603 Belt Pack Manuel utilisateur

Mapei

Mapei Mapeheat Thermo Touch Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuel utilisateur

Sminn

Sminn BOX L VF1L EI Manuel utilisateur

Balboa

Balboa TP600 Manuel utilisateur

Nice

Nice HSCU1 Caractéristiques techniques

Truma

Truma CP plus Manuel utilisateur