Satel CA10 plus Manuel utilisateur

User Manual

Alarm Control Panel CA10 plus

(software version 4.7)

with LCD-S Keypad

GDAŃSK

ca10plcu_s_e 07/03

WARNING

In order to avoid any operational problems with the control panel, it is recommended that

you become familiar with this manual before you start using the equipment.

Making any construction changes or unauthorized repairs is prohibited. This applies, in

particular, to modification of assemblies and components. Maintenance or repair

operations should be performed by authorized personnel (i.e. the installer or factory

service).

Telephone terminals of the panel should be connected to PSTN lines only. Connecting to

ISDN lines may lead to damage of the equipment.

In case of upgrading the PSTN line to ISDN, system owner should contact the installer.

CAUTION!

The alarm system is fitted with a battery. After expiry of its service, the battery must not be

thrown away, but disposed of as required by the existing regulations. (European Union

Directives 91/157/EEC and 93/86/EEC).

The SATEL Company recommends that operation of the whole alarm system be regularly tested.

However, a reliable alarm system does not prevent burglary, assault or fire from happening, it only

diminishes the risk that such a situation will cause no alarm or notification.

History of the updates to this manual is attached at the end hereof.

Control panel CA 10 plus with an LCD-S keypad

Alarm control panel CA10 plus is a modern, microprocessor-based device designed for

signaling burglaries and assaults. The CA-10 plus panel controls the operation of an alarm

system, responds to information coming from the alarm system detectors about an intrusion on

a protected facility and informs about the event. The panel is designed to be operated with LCD

display keypads and LED keypads.

Basic functions of CA-10 plus:

• signaling burglary, panic and fire alarms,

• informing of alarms with telephone voice messages or messages to a paging system,

• answering phone calls and informing the user of system status (whether an alarm

occurred since its arming),

• MONITORING - communication with telephone monitoring stations (real-time

transmission of detailed information about specified events in a protected facility),

• real-time printout of reports on all events in the system on an external printer.

2 User's Guide SATEL

Features of CA-10 plus:

• panel operation controlled with LCD text display keypads (2x16 characters),

• clear text messages describing system status and important events,

• installer-defined zone descriptions simplifying identifying the alarm origin,

• simultaneous detailed status presentation of up to 16 zones controlled by the panel,

• visible clock and system date display helpful in supervising and ensuring error-free

operation,

• reviewing the alarm and trouble logs (or detailed memory log of all system events) with

text description, zone name, partition name or user name and exact time of the event,

• access to numerous USER FUNCTIONS by means of function list item selection.

Armed modes

To adapt the alarm system to various needs the control panel CA-10 plus offers several armed

modes:

Audible armed mode

The mode in which detectors connected to the panel control the protected facility and

violation of the protected zones is signaled by the panel with all available means (sirens,

monitoring stations message transmission, telephone messages).

Control panel CA10 plus with LCD-S keypad 3

Silent armed mode

Armed mode in which alarms are signaled only in the panel keypads. The installer can

decide which of the detectors are automatically by-passed in this mode; he can also choose

signaling device to be used in that mode.

Partial armed mode

The installer can determine the detectors in the system which will be excluded from the

surveillance on arming the system with the special access code (authority level 7). It

enables the user, by entering an appropriate code, to arm the system fully or in a chosen

part only.

Stay armed mode

In this mode the panel enables automatic bypassing of chosen detectors if immediately

after arming the system the user did not leave the facility and did not activate the

entrance/exit detector.

4 User's Guide SATEL

Operating instructions

Operating of the alarm system consists basically in arming and disarming the system (setting

surveillance mode) and offering an appropriate reaction to the information the control panel

signals on the keypad. The keypad displays the information about the status of the alarm

system by means of a two-line, backlit LCD display (2x16 characters) and six additional LED

controls.

LED controls' functions:

• alarm - signals occurrences of alarms.

• trouble - the LED is blinking when the control panel detects a technical problem or a

telephone messaging trouble,

• armed: A B C D - partition status:

- blinking (while the alarm control is off) signals exit delay running,

- control stays on when the partition is armed.

The LEDs marked with letters A B C D correspond to numerical denotation of partitions

available in the system:

LED A – partition 1

LED B – partition 2

LED C – partition 3

LED D – partition 4

Control panel CA10 plus with LCD-S keypad 5

Figure 1. View of LCD-S keypad.

alarm ALARM CONTROL PANEL CA-10 LCD

armed A B C D trouble

1abc 2def 3

ghi 4jkl 5 mno 6

pqrs 7tuv 8wxyz 9

¾0#

8 Sep, 13:26:41

System OK

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

6 User's Guide SATEL

User access codes

For everyday operation of the system assigning user access code is essential. The control

panel comes with one factory-set code (master user code) for each partition:

1234 for partition A,

2345 for partition B,

3456 for partition C,

4567 for partition D.

Programming of additional 12 user access codes is possible in each partition (but no more

than 32 in the entire system). The code can be 4 to 6 digits long.

The number key letters help the user memorize a code by associating it with a particular

word (e.g. the „[5][6][2][7][2]” code corresponds to the word „KOBRA”).

By creating new user access code, the master user assigns specific, so called, authority

level - determines which of the panel functions are available for a particular user, and which

are excluded.

Normally entering access code in one keypad will affect only in one partition. It is possible to

switch on installer accessible option "global access codes". Switching on this option causes,

that users access codes are accepted in all 4 partitions: each user can access do any of

existing partitions. In this case there will be no information about user number in panel’s

event log.

Control panel CA10 plus with LCD-S keypad 7

Arming [Access code][#]

Arming is only possible when the partition is not signaling alarm and is not already armed:

ALARM and ARMED diodes are off.

In order to arm the system access code should be entered and confirmed by pressing [#]

key. If, while typing the code, user makes a mistake [*] key should be pressed and the code

re-entered.

When the code is correctly entered the display shows both a message confirming entering

armed mode and the name of the user who activated it. Then an exit countdown message is

displayed (if the option was allowed by the installer). The partitions in which the countdown

procedure is on are visually represented by blinking ARMED diodes with appropriate

partition letters.

Accepting the command to arm the system can also be confirmed with an appropriate sound

code: three short beeps (if the option of key sound confirmation was turned on by the

installer).

The panel may fail to arm the system if:

• in the panel there are specifically designed zones which cannot be violated while the

system is being armed and one of them is being violated at the time - the panel signals

the situation with three long beeps. In such a case a delay is recommended until all the

exits are ready and arming the system again. Pressing the Wbutton displays the exits

being violated. If one of the exits remains violated (the cause being, for example, the

8 User's Guide SATEL

detector trouble) the armed mode can be switched on after the exit has been blocked

(function 4),

• access code entered is incorrect - the control panel signalizes the event with two long

beeps,

• in the partition there are no armed type zones - the control panel signalizes the event

with two long beeps (access code is correct and allows, for example, to call user

functions),

• battery trouble - three long beeps (proper option is selected to prevent the system from

being armed in case of battery trouble).

Quick Arming [0][#]

On pressing the sequence [0][#] user can, without typing access code, arm the system. The

Quick Arming function can be blocked by the installer. Arming is not influenced by any

detectors being violated at the time. The installer can assign a special key to arm the system

quickly.

Disarming and clearing the alarm [Access code][#]

When the control panel is armed (ARMED diode is on) or signalizes the alarm (ALARM

diode is blinking) it can accept only one order - disarming the system or clearing the alarm.

Typing the access code confirmed by pressing [#] keys disarms the system or turns off the

Autres manuels pour CA10 plus

Table des matières

Autres manuels Satel Panneau de contrôle

Satel

Satel Integra 128-WRL Guide de l'utilisateur

Satel

Satel VERSA Plus Series Manuel du propriétaire

Satel

Satel Versa Plus Manuel de la liste des pièces

Satel

Satel Integra Series Guide de l'utilisateur

Satel

Satel PERFECTA-IP-32 Guide de l'utilisateur

Satel

Satel Integra Series Manuel utilisateur

Satel

Satel Versa Manuel utilisateur

Satel

Satel CA-5 Guide de l'utilisateur

Satel

Satel Versa Plus Manuel du propriétaire

Satel

Satel CA-10 Manuel utilisateur

Satel

Satel INTEGRA Plus Manuel utilisateur

Satel

Satel Versa Manuel utilisateur

Satel

Satel PERFECTA-IP Manuel utilisateur

Satel

Satel CA-6 KLED-S Manuel du propriétaire

Satel

Satel CSP-208 Instructions de montage

Satel

Satel CA-10 Manuel utilisateur

Satel

Satel VERSA Plus LTE Guide de l'utilisateur

Satel

Satel CA10 plus Manuel utilisateur

Satel

Satel INTEGRA Manuel utilisateur

Satel

Satel PERFECTA 16-WRL Manuel du propriétaire

Satel

Satel INTEGRA Plus Manuel du propriétaire

Satel

Satel CA-10 Manuel du propriétaire

Satel

Satel PERFECTA Manuel utilisateur

Satel

Satel ACCO-NT Guide de l'utilisateur

Manuels Panneau de contrôle populaires d'autres marques

RDZ

RDZ PC-HRX Manuel utilisateur

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuel technique

Efka

Efka Variocontrol V810 Manuel utilisateur

Cebora

Cebora 208-10 Manuel utilisateur

AMX

AMX AutoPatch CP-15 Manuel utilisateur

Evolution

Evolution IQ plus 800 Manuel utilisateur

Fagor

Fagor 8040 TCO CNC Manuel utilisateur

Trane

Trane ComfortLink II XL950 Control Manuel utilisateur

AKO

AKO PROCool AKO-17635-2 Manuel utilisateur

ABB

ABB 6136/30M-101 Manuel utilisateur

Telikou

Telikou BK-603 Belt Pack Manuel utilisateur

Mapei

Mapei Mapeheat Thermo Touch Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuel utilisateur

Sminn

Sminn BOX L VF1L EI Manuel utilisateur

Balboa

Balboa TP600 Manuel utilisateur

Nice

Nice HSCU1 Caractéristiques techniques

Truma

Truma CP plus Manuel utilisateur