Sanyo VCB-9124 Manuel utilisateur

INSTRUCTION MANUAL VCB-9124

B/W CCD CAMERA

About this manual

Before installing and using the camera, please read this manual

carefully. Be sure to keep it handy for later reference.

L73D4/US GB 1998, 3, 12

SANYO INDUSTRIAL VIDEO

B/W VIDEO CAMERA LIMITED WARRANTY

OBLIGATIONS

In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty. The names and

addresses of Authorized Sanyo Service Centers may be obtained by writing to SFS Corporation, SFC’s warranty administrator, at any of the addresses listed below, or by calling (toll-free) 1-800-421-5013.

New Jersey Office

210 Riser Road

Little Ferry, NJ 07643

201-641-3000

California Office

1200 W. Artesia Blvd.

Compton, CA 90220

310-537-5830

Illinois Office

900 N. Arlington Heights Rd.

Itasca, IL 60143

708-775-1414

THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA, EXCLUDING HAWAII AND ALL U.S. TERRITORIES AND PROTECTORATES. THIS

WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER

AT THE TIME WARRANTY SERVICE IS REQUESTED.

Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO FISHER (USA) CORPORATION warrants this SANYO product against defects in materials and workmanship for the periods specified below. SFC

will repair or replace (at its option) the product and any of its parts which fail to conform to this warranty. The warranty period commences on the date the product was first purchased or rented at retail.

LABOR PARTS IMAGE DEVICE

2 YEARS 2 YEARS 5 YEARS

EXCLUSIONS

This warranty does not cover (A) the adjustment of customer-operated controls as explained in the appropriate model’s instruction manual, or (B) the repair of any product whose serial number has been altered,defaced

or removed.

This warranty shall not apply to the cabinet or cosmetic parts, antenna, knobs, batteries or image burns to projection or picture tubes caused by electronic devices or games.

This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after repair.

This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from unauthorized

service or parts, improper maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire,

flood or other Acts of God, or normal wear and tear.

The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability.

THE DURATION OF ANY WARRANTIES WHICH MAY BE IMPLIED BY LAW (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS) IS LIMITED TO THE TERM OF THIS WARRANTY. IN NO EVENT

SHALL SFC BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT, OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS

UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL.

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF CONSEQUENTIAL DAMAGES, SO THE ABOVE

LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.

ATTENTION

For your protection in the event of theft or loss of this product, please fill in the information below for you own personal records.

Model No._____________________________________________________________________ Serial No. _____________________________________________________________________

(Located on back or bottom side of unit.)

Date of Purchase _______________________________________________________________ Purchase Price _________________________________________________________________

Where Purchased _________________________________________________________________________________________________________________________________________________

L73D4/US GB 1998, 3, 12

18 English

Safety Guard

THIS SYMBOL INDICATES THAT THERE ARE

IMPORTANT OPERATING AND MAINTENANCE

INSTRUCTIONS IN THE LITERATURE ACCOMPANYING

THIS UNIT.

ARNING:

TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This installation should be made by a qualified service person and

should conform to all local codes.

INFORMATION TO USER

For the customers in Canada

This Class B digital apparatus complies with Canadian ICES- 3.

Pour la clientèle canadienne

Cet appareil numerique de la Classe B est conforme a la norme

NMB- 3 du Canada.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of

the following measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician for

help.

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

Changes or modifications not expressly approved by Sanyo may

void the user’s authority to operate this camera.

L73D4/US GB 1998, 3, 12

English 1

CONTENTS

PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

PARTS NAMES AND FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

PREPARATIONS AND CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 7

CONNECTIONS AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 8

SETTINGS AND ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

INFRARED (IR LED) ILLUMINATION RANGE . . . . . . . . . . . . . . . . . . . . 14

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Accessories

Screws for base installation

(4 x 35 tapping screws)

The rated value label is located on the back of the camera.

FEATURES

•Built-in interline transfer method 1/3" CCD, approx. 27 ,

picture elements

•Low smear, anti-blooming, low lag, no burning and no geometric

distortion using the CCD solid state image device

•Built-in Vari Focal type auto iris lens, F=2. - 2.7, f=2,6 - 5.6 mm

•1 % solid state components giving excellent immunity to shock

and vibration

•Not subject to interference from magnetic or electrostatic fields

•Built-in IR. LED by very required mininum illumination is approx.

lux at 4.5 m

•Horizontal resolution, more than 4 TV lines

•With manual PAN/TILT/ROUND mechanism

•Power supply: 24 V AC operation

L73D4/US GB 1998, 3, 12

English 2

PRECAUTIONS

In case of problem

Do not use the camera if smoke or a strange odour comes from the

unit, or if it seems not to function correctly. Disconnect the power

cord immediately, and consult your dealer (or a Sanyo Authorized

Service Centre).

Do not open or modify

Do not open the cabinet, as it may be dangerous and cause damage

to the unit. For internal settings and repairs, consult your dealer (or a

Sanyo Authorized Service Centre).

Do not put objects inside the unit

Make sure that no metal objects or flammable substance get inside

the camera. If used with a foreign object inside, it could cause a fire,

short-circuits or damages.

If water or a liquid gets inside the camera, disconnect the power cord

immediately, and consult your dealer (or a Sanyo Authorized Service

Centre). Be careful to protect the camera from rain, sea water, etc.

Be careful when handling the unit

To prevent damages, do not drop the camera or subject it to strong

shock or vibration.

Install away from electric or magnetic fields

If installed close to a TV, radio transmitter, magnet, electric motor,

transformer, audio speakers the magnetic field they generate will

distort the image.

Protect from humidity and dust

To prevent damages to the camera, do not install it where there is

greasy smoke or steam, where the dampness may get too high, or

where there is a lot of dust.

Protect from high temperatures

Do not install close to stoves, or other heat generating devices, such

as spotlights, etc., or where it could be subject to direct sunlight, as

that could cause deformation, discoloration or other damages.

Be careful when installing close to the ceiling, in a kitchen or boiler

room, as the temperature may raise to high levels.

Install where the temperature range will stay between –1 ˚C and

5 ˚C. (no condensation)

Cleaning

•Dirt can be removed from the cabinet by wiping it with a soft

cloth. To remove stains, wipe with a soft cloth moistened with a

soft detergent solution and wrung dry, then wipe dry with dry soft

cloth.

•Do not use benzine, thinner or other chemical product on the

cabinet, as that may cause deformation and paint peeling. Before

using a chemical cloth, make sure to read all accompanying

instructions. Make sure that no plastic or rubber material comes in

contact with the cabinet for a long period of time, as that may

cause damage or paint peeling.

L73D4/US GB 1998, 3, 12

English 3

PARTS NAMES AND FUNCTIONS

MONITOR

GND

BLC

LEVEL

HILJK

L-PHASE

Manual pan, tilt and rotation

The angle of the lens can be adjusted

manually in ranges indicated below.

A: Horizontally ± 45˚

B: Vertically ± 6 ˚

C: Rotation of the camera unit ± 35˚

L73D4/US GB 1998, 3, 12

English 4

PARTS NAMES AND FUNCTIONS

1Camera unit fixing screws (4)

These screws are used to attach the camera unit to the base.

Tighten the four screws evenly when attaching the camera unit.

2Screw openings for base installation

These openings are to attach the base to the ceiling or a wall

using the four supplied tapping screws.

3CAMERA (VIDEO) OUT terminal screw

Video signal output terminal. Insert the center wire of the coaxial

cable into the CAMERA OUT terminal, then tighten the screw to

secure it.

4GND (ground) terminal screw

Video signal ground terminal. Insert the shielding mesh of the

coaxial cable under the GND terminal plate, then tighten the

screw to secure it.

5Cabling tab

When the cables cannot be run behind the ceiling, etc., remove

this tab to allow the coaxial cable to go through.

624 V AC input terminal

(24 V AC, GND)

With this camera use only the 24 V AC

power adaptor model No. VPT-115

available from Sanyo.

Power supply connections

Use a 3 wire grounded cable (22 AWG

or more), and connect as shown by the

illustration.

CAUTION:

• To prevent camera and/or AC

adaptor failure, pay close attention

polarity when making the connections.

• To prevent fire hazard any UL listed

wire rated VW-1, should be used for

the 24 V AC cable input terminal.

7Lens cover

This cover will protect the lens from dust and damage. Turn the

cover in the direction of the arrow, shown on the illustration, to

remove it. To install the cover, align the tabs (A) with the

openings, then turn it in the opposite direction.

GND

AC AC

L73D4/US GB 1998, 3, 12

English 5

PARTS NAMES AND FUNCTIONS

8Secondary lens cover

9Lens

FFocus ring

To set the focus, loosen the focus ring knob, then turn the ring

towards ∞ (infinity) or N (near) as necessary. When the focus is

set as desired, tighten the focus ring knob.

GZoom ring

To adjust the viewing range (zoom), loosen the zoom ring knob,

then turn the ring towards T (the range will be smaller and the

subject larger) or W (the range will be wider and the subject

smaller) as necessary. When the zoom is set as desired, tighten

the zoom ring knob.

HGND (ground) pin

For monitor use. (See I)

IMONITOR output pin

When setting up the camera, connect a monitor to this video

output pin and to the GND pin using alligator clip cables, then

using the image displayed on the monitor, set the surveillance

angle and range, the lens focus, etc.

JBLC (backlight compensation) switch

0: Backlight compensation off

1: Backlight compensation on

For backlight compensation, set the BLC switch to 1, then, if

necessary, adjust the LEVEL volume control.

KLEVEL volume control

Used when the BLC switch is set to 1. Under normal conditions, it

should be turned all the way to the left. When adjusting the

backlight compensation, turn it to the right until the desired

correction level is obtained.

LL-PHASE (line phase) volume control

Used when the SYC switch is set to 1. Turn it to adjust the line

phase between two or more cameras.

L73D4/US GB 1998, 3, 12

English 6

PREPARATIONS AND CONNECTIONS

Concerning the coaxial cable

To connect the camera to peripheral devices, use a coaxial cable with BNC plug.

•Cable type RG-6U (5C-2V), 5 m maximum.

•Cable type RG-11U (7C-2V), 6 m maximum.

If the type of peripheral devices connected, the type of cable used and/or the cable length

are not as specified, the image and synchronization signals may not be transmitted

correctly.

CAUTION:

Use CCTV/Video grade coaxial cable. Due to its construction, an RG-59U cable will not

transmit the signal properly when installed through conduits or through the air, and

therefore cannot be used.

Installing the BNC plug (sold separately)

1Cut the extremity of the coaxial cable (sold separately), as illustrated.

2Insert the cable through the adaptor, then turn the shielding mesh over.

3Loosen the center wire securing screw of the plug, then install the cable in the BNC

plug, so that the center wire is threaded through the plug center opening.

Before tightening the center wire securing screw, make sure the center wire comes out

through the plug center opening.

4Screw the adaptor onto the plug.

7mm 8mm

3 4

1 2

L73D4/US GB 1998, 3, 12

English 7

CONNECTIONS AND INSTALLATION

Basic connections for monitoring or recording

The peripheral devices (VCR, monitor, etc.) and cables are sold separately.

1Make the video signal connection between the camera and the monitor or time lapse

VCR.

2Plug the AC adaptor to a wall outlet.

Adjust the picture on the monitor using the Brightness and Contrast controls.

Multiple cameras connection

You can use multiple cameras by connecting them a camera switcher or a quad unit (sold

separately), then conducting the surveillance from one location by splitting the monitor screen

to view the image from each camera, or by switching the image from each camera on the

monitor screen. For detailed information, please refer to the installed devices instruction

manuals.

(Example of connection to a monitor)

NOTE: (Fig. 1)

•Make sure the AC adaptor is not

connected to the wall outlet before

connecting it to the 12 V DC input

terminals.

•When making the connections be careful

to respect the polarity and not to

shortcut the terminals.

Table des matières

Autres manuels Sanyo Caméra de sécurité

Sanyo

Sanyo VDC-HD3300 - Full HD 1080p Vandal Dome... Manuel utilisateur

Sanyo

Sanyo VCB-3412P Manuel utilisateur

Sanyo

Sanyo VCC-XZ200P Manuel utilisateur

Sanyo

Sanyo VCC-ZM300PA Manuel utilisateur

Sanyo

Sanyo VCC-9000EBCP/EBSP Manuel utilisateur

Sanyo

Sanyo VCC-4795P Manuel utilisateur

Sanyo

Sanyo VCC-ZM300 Manuel utilisateur

Sanyo

Sanyo VCC-ZM300A Manuel utilisateur

Sanyo

Sanyo Colour CCD Camera VCC-5775P Manuel utilisateur

Sanyo

Sanyo VCC-P7574 - 1/4" Color CCD Indoor Mini Dome... Manuel utilisateur

Sanyo

Sanyo VCC-HD2300 - Full HD 1080p Network Camera Manuel utilisateur

Sanyo

Sanyo VCB-7312P Manuel utilisateur

Sanyo

Sanyo VCC-HD2300P Instructions de construction

Sanyo

Sanyo VCC-WB4000P Manuel utilisateur

Sanyo

Sanyo VCB-3372 Manuel utilisateur

Sanyo

Sanyo VCC-9684VA - 1/4" Color CCD Indoor Mini Dome... Manuel utilisateur

Sanyo

Sanyo VDC-D1184VA Manuel utilisateur

Sanyo

Sanyo VCC-P7574 - 1/4" Color CCD Indoor Mini Dome... Manuel utilisateur

Sanyo

Sanyo VDC-DP7584 - 1/4" Color CCD Vandal-Resistant Dome... Manuel utilisateur

Sanyo

Sanyo VCC-HD4600 - Full HD 1080p Day/Night Network... Manuel utilisateur

Sanyo

Sanyo VDC-DP9584S Manuel utilisateur

Sanyo

Sanyo VCC-P6784 Manuel utilisateur

Sanyo

Sanyo VCC-6574 Manuel utilisateur

Sanyo

Sanyo VCC-ZM300PA Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur