Sanyo PLC-XP30 Manuel utilisateur

PRODUCT CODE

(MM6A) 1 122 085 00 : U.S.A., Canada

(PM6A) 1 122 086 00 : Europe, Asia, Africa, M.E.

(PM6C) 1 122 086 02 : U.K. REFERENCE NO. SM5110189

PLC-XP30

Multimedia ProjectorMODEL

Give complete “CHASSIS NO." for

parts order or servicing, it is shown on

the rating sheet on the cabinet of the

Projector.

Chassis No. MM6-XP3000

NOTE: Match the Chassis No.on the rating

sheet on the cabinet with the

Chassis No. in the Service

Manual.

If the Original Version Service

Manual Chassis No. does not

match the unit’s, additional

Service Literature is required.You

must refer to “Notices” to the

Original Service Manual prior to

servicing the unit.

CONTENTS:

Specifications 2

Safety Instructions 3

Protections 4

Ass'y lamp replacement 6

Mechanical disassemblies 7

Optical unit disassemblies 11

Troubleshooting 15

Waveforms 24

Electrical adjustments 27

Optical adjustments 34

CPU input/output port functions 40

Notes on schematic diagram 42

Parts list 43

Cabinet, Chassis and Optical parts list 48

Electrical parts list 53

Block diagrams B1~B5

PWB parts location diagrams P1~P5

Schematic diagrams S1~S8

■Specifications

1.3" TFT Active Matrix type, 3 panels

TECHNICAL SPECIFICATIONS

Multi-media Projector

20.3 lbs (9.2 kg)

12.44" x 6.46" x 18.9" (316mm x 164mm x 480mm)

1024 x 768 dots

2,359,296 (1024 x 768 x 3 panels)

PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N

H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz

Adjustable from 31”to 400”

800 TV lines

2 speakers, 1.57" x 2.76" (40mm x 70mm)

41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)

14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)

Owner’s Manual

AC Power Cord

Wired/Wireless Remote Control Transmitter and Batteries

VGA Cable

MAC Adapter

Control Cable for PS/2 port

Control Cable for Serial port

Control Cable for ADB port

Remote Control Cable

Dust Cover

Lens Cover

Projector Type

Net Weight

Dimensions (W x H x D)

Panel Resolution

Number of Pixels

Color System

Scanning Frequency

Projection Image size (Diagonal)

Horizontal Resolution

Built-in Speakers

Operating Temperature

Storage Temperature

Accessories

LCD Panel System

●The specifications are subject to change without notice.

F 1.8 ~ 2.1 lens with f 48.4 mm ~ 62.8 mm with motor zoom, focus and shift

4.6’~ 47.2’(1.4 m ~ 14.4 m)

250 W

RCA Type x 3 (Video/Y, Pb/Cb, Pr/Cr) and Mini DIN 4 pin x 1 (S-Video)

Projection Lens

Throw Distance

Projection Lamp

AV Input Jacks RCA Type x 2

AV Audio Input Jacks (VGA) HDB 15 Terminal x 1, DVI 24 pin x 1, and BNC jack x 5

Mini Jack (stereo) x 2

Mini DIN 8 pin x 2

RCA Type x 2

2.0 W RMS (stereo)

Computer Input Jacks

Computer Audio Input Jacks

Control Port Jacks

Audio Output Jacks

Internal Audio Amp

0˚to 9.0˚

Feet Adjustment

Power Source : AA, UM3 or R06 Type x 2

Operating Range : 16.4’(5m) / ±30˚

Dimensions : 2.2”x 1.3”x 7.6”(55mm x 34mm x 192mm)

Net Weight : 0.36 lbs (165 g) (including batteries)

Laser Pointer : Class II Laser (Max. Output : 1mW / Wave length : 650±20nm)

Remote Control Transmitter

480i, 480p, 575i, 575p, 720p, 1035i, 1080i-50 and 1080i-60

High Definition TV Signal

BNC jack x 5 (Computer) and RCAType x 1(Video)

Monitor Output Jacks

AC 100 ~ 120 V (4.4 A Max.Ampere), 50 / 60 Hz

(The U.S.A and Canada)

AC 200 ~ 240 V (2.2 A Max.Ampere), 50 / 60 Hz

(Continental Europe and The U.K.)

Voltage and

Power Consumption

-3-

SERVICE PERSONNEL WARNING

Eye damage may result from directly viewing the

light produced by the Lamp used in this equipment.

Always turn off Lamp before opening cover. The

Ultraviolet radiation eye protection is required during

this servicing.

Never turn the power on without the lamp to avoid

electric-shock or damage of the devices since the

stabilizer generates high voltages (20~25kV) at its

starts.

Since the lamp is very high temperature during units

operation. Replacement of the lamp should be done

at least 45 minutes after the power has been turned

off, to allow the lamp cool-off.

WARNING:

The chassis of this projector is isolated (COLD) from

AC line by using the converter transformer. Primary

side of the converter and lamp power supply unit cir-

cuit is connected to the AC line and it is hot, which

hot circuit is identified with the line ( ) in the

schematic diagram.For continued product safety and

protection of personnel injury, servicing should be

made with qualified personnel.

The following precautions must be observed.

SAFETY PRECAUTIONS

1: An isolation transformer should be connected in the

power line between the projector and the AC line

before any service is performed on the projector.

2: Comply with all caution and safety-related notes pro-

vided on the cabinet back, cabinet bottom, inside the

cabinet or on the chassis.

3: When replacing a chassis in the cabinet, always be

certain that all the protective devices are installed

properly, such as, control knobs, adjustment covers

or shields, barriers, etc.

DO NOT OPERATE THIS PROJECTOR WITHOUT

THE PROTECTIVE SHIELD IN POSITION AND

PROPERLY SECURED.

4: Before replacing the cabinet cover, thoroughly

inspect the inside of the cabinet to see that no stray

parts or tools have been left inside.

Before returning any projector to the customer, the

service personnel must be sure it is completely safe

to operate without danger of electric shock.

PRODUCT SAFETY NOTICE

Product safety should be considered when a compo-

nent replacement is made in any area of the projec-

tor. Components indicated by mark in the parts

list and the schematic diagram designate compo-

nents in which safety can be of special significance.

It is, therefore, particularly recommended that the

replacement of the parts must be made by exactly

the same parts.

DO NOT ATTEMPT TO SERVICING THE

REMOTE CONTROL UNIT.

Laser Beam may be leaked out when in disassem-

ble the Unit. As the Laser Beam used in this

Remote control unit is harmful to the eyes.

LASER RADIATION

DO NOT STARE INTO BEAM

MAX. OUTPUT: 1mW

WAVE LENGTH: 650 ±20nm

CLASS II LASER PRODUCT

This product is complied with 21 CFR

part 1040.10

CAUTION LASER RADIATION

DO NOT STARE INTO BEAM

CLASS 2 LASER PRODUCT

LASER-STRAHLING

NICHT IN DEN STRAHL BLICKEN

LASER KLASSE 2

IEC60825-1, Am. 1 1997

MAX OUTPUT ( ) : 1 mW

WAVE LENGTH ( ) : 650±20nm

■Safety Instructions

-4-

The fuse is located inside of the projector. When either the LAMP indicator or the

READY indicator is not illuminated, the fuse may be opened. Check the fuse as

following steps.

The specified fuse should be used as follows;

How to replace the fuse

1. Remove the cabinet top refer to “Mechanical Disassemblies”.

2. Remove the fuse from fuse holder.

To install the fuse, take reversed step in the above.

Fuse Part No.: 423 021 7801

TYPE T6.3AH 250V FUSE

LITTLE FUSE INC.TYPE 21506.3

Protections

This projector is equipped with the following protections to operate in safety. If the abnormality occurs inside the

projector, it will automatically turn off by operating one of the following protection circuits.

❏ Circuit Protection - Fuse

-5-

Interlock

switch

SW902

Lamp

cover

There is the thermal switch (SW905) inside of the projector to

prevent the internal temperature from rising abnormally.

When the internal temperature reaches near 100˚C, the AC

main power supply is automatically turned off.

The thermal switch is not reset to normal automatically even if

the internal temperature becomes normal. Reset the thermal

switch with the following procedure.

Check the resistance between terminals of thermal switch by

using the tester. If it has high impedance, thermal switch may

be in operative.

How to reset the thermal switch

1. Remove the cabinet top refer to “Mechanical

Disassemblies”.

2. Press the reset button on the thermal switch.

CAUTION:

Before pressing the reset button, disconnect the AC cord from

the projector.

❏ The lamp circuit of this projector is not iso-

lated from AC line, and it is HOT circuit.

❏ The Interlock switch (SW902) cuts off the

lamp circuit from AC line when lamp cover

is removed.

❏ Electric shock protection - Interlock switch (SW902)

(TERMOSTAT-SW)

SW905

INTERLOCK

SW902

(LIVE)

MAINS SW

SW901

F901

LF901

W901

Reset

button

Press

❏ Optical Protection - Thermal switch

-6-

LAMP REPLACEMENT

When the life of the Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights yellow.

When the image becomes dark or the color of the image becomes unnatural, replacement of the Lamp is

required.

Turn off the projector and disconnect the AC plug. Allow the

projector to cool for at least 45 minutes.

Remove the two screws with a screwdriver and pull out the Lamp

Assembly by grasping the handle.

LAMP REPLACEMENT MONITOR TIMER

Replace the Lamp Assembly with a new one and tighten the two

screws. Make sure that the Lamp Assembly is set properly.

Replace the Lamp Cover and tighten the screw.

Remove the screw with a screwdriver and remove the Lamp

Cover.

CAUTION

●For continued safety, replace with a lamp assembly of the same type.

●Allow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector

can be very hot.

●Do not drop the lamp assembly or touch the glass bulb! The glass can shatter and may cause injury.

Be sure to reset the Lamp Replacement Monitor Timer when the Lamp Assembly is replaced. When the Lamp

Replacement Monitor Timer is reset, the LAMP REPLACEMENT indicator stops lighting.

Turn the projector on, and press the MENU button and the ON-SCREEN MENU will appear. Press the POINT

LEFT/RIGHT buttons to select SETTING and press the SELECT button (refer to the page 36, 37). Another dialog box

SETTING MENU will appear.

Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to “Lamp age,”and then press the

SELECT button. The message "Lamp replace monitor Reset?" is displayed.

Do not reset the Lamp Replacement Monitor Timer, except after the lamp is replaced.

Connect the AC Power Cord to the projector and turn the

projector on.

Follow these steps to replace the lamp assembly.

Reset the Lamp Replacement Monitor Timer (refer to the section

“Lamp Replacement Monitor Timer”below).

Select [Yes] to reset the Timer.

LAMP

ASSEMBLY

HANDLE

LAMP COVER

NOTE : Do not reset the LAMP REPLACEMENT MONITOR

TIMER when the lamp is not replaced.

ORDER REPLACEMENT LAMP

Replacement Lamp can be ordered through your dealer. When ordering the Lamp, give the following information

to the dealer.

●Replacement Lamp Type No. : POA-LMP28

(Service Parts No.610 285 4824)

-7-

Cabinet-front-A

Button

Cabinet-top

Mounting-coverlens

1. Adjustable-Feet and Cabinet-front-

A Removal

2. Mounting-cover-lens and Cabinet-

top Removal

Mechanical Disassemblies

1. Remove 1 screw-A.

2. Pull the foot. (arrow-1)

3. Pull the foot,(arrow-2) and

remove.

4. Remove the other foot in the

same way.

5. Remove 2 screws-B.

6. Push the button and pull the

Cabinet-front-A (arrow-3)

and remove.

1. Remove 4 screws on side, 2 screws

on top and 1 screw on rear.

2. Grasp the two sides, pull the cabi-

net top upward and remove.

3. Pull the Mounting-cover-lens

upward and remove.

-8-

3. Cabinet-front Removal.

4. Ass'y-Main Removal.

1. Remove 2 screws on side and 2

screws on bottom.

2. Grasp the two sides, pull the cabi-

net-front forward and remove.

1. Remove 11 screws and disconnect

the FPC cables etc. and then

remove the ass'y main.

-9-

Ass'y R/C Rear

Cover power

Ass'y Power

Ass'y Subpower

Ass'y Motor-drive

Ass'y

Lampballast

5. Unit-AV/Video Removal.

6. Ass'y-power,

Ass'y-subpower,

Ass'y-motor-drive,

Ass'y-Lamp-ballast,

Fan and ass'y R/C rear Removal.

1. Pull the Unit-AV/Video upward

and remove.

1. Remove 3 screws-A and then remove the cover-

power.

2. Pull the ass'y Power and Subpower upward and

remove.

3. Remove 3 screws-B and then remove the Ass'y-

motor-drive.

4. Remove 3 screws-C and then remove the Ass'y-

Lamp-ballast

5. Remove 4 screws-D and then remove the Fan.

6. Pull the ass'y R/C rear upward and remove.

-10-

Lens-shift-unit

Projection-lens

7. Optical-unit

Removal.

8. Projection-lens, Lens-shift-unit and

Fan Removal.

1. Remove 10 screws and then pull the

Optical unit upward and remove .

1. Remove 4 screws-A and then remove the

Projection-lens.

2. Remove 4 screws-B and then remove the Lens-

shift-unit.

3. Remove 4 screws-C and then remove the Fan.

Autres manuels pour PLC-XP30

Table des matières

Autres manuels Sanyo Projecteur

Sanyo

Sanyo PLV-Z2 Manuel utilisateur

Sanyo

Sanyo PLC-EF12N Manuel utilisateur

Sanyo

Sanyo PLC-XU106 Mode d’emploi

Sanyo

Sanyo PLC-5600N Manuel utilisateur

Sanyo

Sanyo PDG-DXL100 - XGA DLP Projector Manuel utilisateur

Sanyo

Sanyo PDG-DSU30 - 2500 Manuel utilisateur

Sanyo

Sanyo PLC-XU22E Manuel utilisateur

Sanyo

Sanyo PLC-WM5500/L - 5500 Lumens Manuel utilisateur

Sanyo

Sanyo PLC-400N Manuel utilisateur

Sanyo

Sanyo PLC-EF10N - SXGA LCD Projector Manuel utilisateur

Sanyo

Sanyo PDG-DSU21N - SVGA DLP Projector Manuel utilisateur

Sanyo

Sanyo PLC-XM150L Manuel utilisateur

Sanyo

Sanyo PLC-XU106 Manuel utilisateur

Sanyo

Sanyo PLC-XU47 Guide d'installation

Sanyo

Sanyo PLC-XU3001 Manuel utilisateur

Sanyo

Sanyo PLC-XF47 Manuel utilisateur

Sanyo

Sanyo PLC-XP21N Instructions de montage

Sanyo

Sanyo PLC-XP100BKL Manuel utilisateur

Sanyo

Sanyo PLC-300M Manuel utilisateur

Sanyo

Sanyo 3000 ANSI LUMENS PLC-XU305 Manuel d'installation

Sanyo

Sanyo PLC-XF30 Guide de démarrage rapide

Sanyo

Sanyo PLC-SU20N Manuel utilisateur

Sanyo

Sanyo SW15 - PLC SVGA LCD Projector Manuel utilisateur

Sanyo

Sanyo PLC-WL2503 Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur