Sanyo PDG-DXL2000 - 2000 Lumens Guide de configuration

The WARNING TEMP. indicator shows the state of the function which protects the projector. Check the state of

the WARNING TEMP. indicator and the POWER indicator to take proper maintenance.

WARNING TEMP. indicator

The projector is shut down and the WARNIN TEMP.

indicator is blinking red.

When the temperature inside the projector reaches a

certain level, the projector will be automatically shut down to

protect the inside of the projector. The POWER indicator is

blinking while the projector is being cooled down. When the

projector has cooled down enough (to its normal operating

temperature), it can be turned on again by pressing the ON/

STAND-BY button.

The projector is shut down and the WARNING

TEMP. indicator lights red.

When the projector detects an abnormal condition, it is

automatically shut down to protect the inside of the projector

and the WARNING TEMP. indicator lights red. In this case,

unplug the AC power cord and reconnect it, and then

turn the projector on once again to verify operation. If the

projector can not be turned on and the WARNING TEMP.

indicator still lights red, unplug the AC power cord and

contact the service center.

CAUTION

DO NOT LEAVE THE PROJECTOR WITH THE

AC POWER CORD CONNECTED UNDER AN

ABNORMAL CONDITION. IT MAY RESULT IN

FIRE OR ELECTRIC SHOCK.

Maintenance and Cleaning

Top Panel

Note:

The WARNING TEMP. indicator continues to blink even

after the temperature inside the projector returns to

normal. When the projector is turned on again, the

WARNING TEMP. indicator stops blinking.

Then check the matters below:

– Did you provide appropriate space for the projector to be

ventilated? Check the installing condition to see if the air

vents of the projector are not blocked.

– Has the projector been installed near an Air-Conditioning/

Heating Duct or Vent? Move the installation of the

projector away from the duct or vent.

– Is the filter clean? Replace the filter with a new one.

Emit a red light

Blinking red

Top Panel

Be sure to reset the Filter counter after replacing the Filter .

Resetting the Filter Counter

Maintenance and Cleaning

Turn off the projector, and unplug the AC power cord

from the AC outlet.

First, clean up the dust on the projector and around the

air vents.

Filter prevents dust from accumulating on the optical elements inside the projector. Should the Filter become

clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup

and adversely affect the life of the projector. If a “Filter warning” icon appears on the screen, replace the Filter

immediately. Replace the filter by following the steps below.

Loosen the screw and open the lamp cover and lift the

filter out of the projector.

CAUTION

- Do not operate the projector with the filter removed.

Dust may accumulate on the optical elements

degrading picture quality.

- Do not put anything into the air vents. Doing so may

result in malfunction of the projector.

- Do not wash the filter with water or any other liquid

matter. Otherwise the filter may be damaged.

RECOMMENDATION

We recommend avoiding dusty/smoky environments

when you operate the projector. Usage in these

environments may cause poor image quality.

When using the projector under dusty or smoky conditions,

dust may accumulate on a lens or optical elements inside

the projector degrading the quality of a projected image.

When the symptoms above are noticed, contact your

authorized dealer or service center for proper cleaning.

Replacing the Filter

Press the MENU button to display the On-Screen

Menu. Use the Point 54buttons to select Setting and

then press the Point or the SELECT button.

Use the Point 54buttons to select Filter counter

and then press the SELECT button. Use the Point 54

buttons to select Filter counter reset and then press

the SELECT button. Filter counter Reset? appears.

Select Yes to continue.

Filter counter

Reset? appears.

Select Yes, then

another confirmation

box appears.

Select Yes again

to reset the Filter

counter.

Another confirmation dialog box appears, select Yes to

reset the Filter counter.

Put the new one back into the position, and close the

lamp cover and secure the screw.

5Connect the AC power cord to the projector and turn

on the projector.

6Reset the filter counter.

Lamp Cover

Screw

Filter

Cleaning the Projector Cabinet

Cleaning the Projection Window

Unplug the AC power cord before cleaning.

First, remove the dust with a commercially available air

blower. Then gently wipe the projection window surface.

Use a cleaning paper moistened with methyl alcohol

(methanol). Avoid using an excessive amount of cleaner.

Do not use abrasive cleaners, solvents, or other harsh

chemical cleaners to avoid damaging the projection window.

Unplug the AC power cord before cleaning.

Gently wipe the projector body with a soft dry cleaning cloth.

When the cabinet is heavily soiled, use a small amount of

mild detergent and finish with a soft dry cleaning cloth. Avoid

using an excessive amount of cleaner. Abrasive cleaners,

solvents, or other harsh chemicals might scratch the surface

of the cabinet.

When the projector is not in use, put the projector in

an appropriate carrying case to protect it from dust and

scratches.

Maintenance and Cleaning

CAUTION

Do not use any flammable solvents or air sprays

on the projector and in its vicinity. The explosion

or fire hazard may occur even after the AC power

cord is unplugged because the temperature inside

the projector is extremely high due to the lamps. In

addition, there is a risk that the internal parts may

be damaged not only by the flammable air spray but

also by the cold air.

CAUTION

This projector is equipped with a projection window.

- Do not rub the projection window with a hard fiber

cloth or hit it with a something hard to prevent the

projection window from scratching.

- Do not use a chemical cleaner (liquid and solid) to

avoid deteriorating the projection window.

When the projection lamp of the projector reaches its end

of life, the Lamp replacement icon appears on the screen

and LAMP REPLACE indicator lights yellow. Replace the

lamp with a new one promptly. The timing when the LAMP

REPLACE indicator should light is depending on the lamp

mode.

For continued safety, replace with a lamp of the

same type. Do not drop a lamp or touch a glass

bulb! The glass can shatter and may cause injury.

Allow a projector to cool for at least 45 minutes

before you open the Lamp Cover. The inside of

the projector can become very hot.

CAUTION

Lamp Replacement

CAUTION

Maintenance and Cleaning

Follow these steps to replace the lamp.

Turn off the projector and unplug the AC power cord.

Let the projector cool for at least 45 minutes.

Loosen the two (2) screws that secure the lamp. Lift

the lamp out of the projector by using the handle.

Replace the lamp with a new one and secure the two

(2) screws. Make sure that the lamp is set properly.

Close the lamp cover and secure the screw.

Loosen the screw and open the lamp cover.

Connect the AC power cord to the projector and turn

on the projector.

6Reset the lamp counter.

See “Resetting the Lamp Counter” on the next page.

Screw

ORDER REPLACEMENT LAMP

Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following

information to the dealer.

LModel No. of your projector : PDG-DXL2000

LReplacement Lamp Type No. : POA-LMP143

(Service Parts No. 610 351 3744)

Top Panel

When replacing the lamp because it has stopped

illuminating, there is a possibility that the lamp

may be broken. If replacing the lamp of a projector

which has been installed on the ceiling, you should

always assume that the lamp is broken, and you

should stand to the side of the lamp cover, not

underneath it. Remove the lamp cover gently.

Small pieces of glass may fall out when the lamp

cover is opened. If pieces of glass get into your

eyes or mouth, seek medical advice immediately.

CAUTION

Screws

Handle

Lamp replacement icon

WARNING:

TURN OFF THE UV LAMP BEFORE

OPENING THE LAMP COVER Note:

The Lamp replacement icon will not appear when

the Display function is set to Off (p.53), during

Freeze (p.28), or No show (p.29).

This indicator turns yellow

when the projection lamp

reaches the end of its life.

Lamp Cover

Lamp

This projector uses a high-pressure lamp which must be handled carefully and properly.

Improper handling may result in accidents, injury, or create a fire hazard.

LLamp life may differ from lamp to lamp and according to the environment of use. There is no guarantee

of the same life for each lamp. Some lamps may fail or terminate their life in a shorter period of time than

other similar lamps.

LIf the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights

up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.

(Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of

the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.

LA Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its

lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in

which the projector and lamp are being used.

IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.

If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an

authorized service center for a checkup of the unit and replacement of the lamp. Additionally, check

carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out

from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one

should check the inside of the projector except those who are authorized trained technicians and who

are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those

who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken

glass.

LAMP HANDLING PRECAUTIONS

Maintenance and Cleaning

Resetting the Lamp Counter

Be sure to reset the Lamp counter after the lamp is replaced. When the Lamp counter is reset, the LAMP

REPLACE indicator stops lighting and the Lamp replacement icon disappears.

Note:

Do not reset the Lamp counter without implementing

lamp replacement. Be sure to reset the Lamp counter

only after replacing the lamp.

Lamp replacement

counter Reset?

appears.

Select Yes, then

another confirmation

box appears.

Select Yes again

to reset the Lamp

counter.

Press the MENU button to display the On-Screen

Menu. Use the Point 54buttons to select Setting

and then press the Point or the SELECT button.

Use the Point 54buttons to select Lamp counter

and then press the SELECT button. Use the Point

54buttons to select Lamp counter reset and then

press SELECT button. Lamp replacement counter

Reset? appears. Select Yes to continue.

Another confirmation dialog box appears, select Yes

to reset the Lamp counter.

Autres manuels pour PDG-DXL2000 - 2000 Lumens

Table des matières

Autres manuels Sanyo Projecteur

Sanyo

Sanyo PLC-SU50S Manuel utilisateur

Sanyo

Sanyo PLC-XP30 Manuel utilisateur

Sanyo

Sanyo PLC-XU70 Manuel utilisateur

Sanyo

Sanyo PLC-WM4500/L Manuel utilisateur

Sanyo

Sanyo WXU700A Manuel utilisateur

Sanyo

Sanyo PLC-XT11 Manuel utilisateur

Sanyo

Sanyo PLC-SP10N Manuel utilisateur

Sanyo

Sanyo PLC-XM100/L - 5000 Lumens Manuel utilisateur

Sanyo

Sanyo LNS-W10 - Wide-angle Zoom Lens Manuel d'utilisation et d'entretien

Sanyo

Sanyo PLC-XT20K Manuel utilisateur

Sanyo

Sanyo PLC-SU31 Manuel utilisateur

Sanyo

Sanyo XGA ULTRA SHORT-THROW PLC-XL51 Manuel utilisateur

Sanyo

Sanyo PLC-XU58 Manuel utilisateur

Sanyo

Sanyo PLC-XE30 Manuel utilisateur

Sanyo

Sanyo BUNDLE PLC-WL2500S Manuel utilisateur

Sanyo

Sanyo PLC-WM4500/L - 4500 Lumens Manuel utilisateur

Sanyo

Sanyo PLC-XL51 - 2700 Lumens Manuel utilisateur

Sanyo

Sanyo PLC-EF60A Manuel utilisateur

Sanyo

Sanyo PLC-XP07N Manuel utilisateur

Sanyo

Sanyo PDG-DSU21 Manuel utilisateur

Sanyo

Sanyo PLC-XU47 Guide d'installation

Sanyo

Sanyo PLC-XU300A - 3000 Lumens Manuel utilisateur

Sanyo

Sanyo PLC-EF60 Manuel utilisateur

Sanyo

Sanyo PLC-XP07N Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur