SANLI MT426 Manuel utilisateur
Please read this instruction manual carefully
before operating your machine.
MT426
Congratulations on choosing a Sanli Multi tool.
Thank you for purchasing a Sanli 2-stroke multi tool. We are sure that you’ll enjoy
many years of
trouble-free performance, plus you have the reassurance of a 24
month warranty.
Inside this guide you will find out all you need to know to correctly operate your new
Sanli Multi
tool. To ensure that you use your new multi tool responsibly and get the
best results possible,
please read all of the safety and operating instructions
carefully.
Contents
Sanli multi tool features
Tips on multi tool safety
Attaching the handle ---straight shaft.
Attaching the safety guard---straight shaft.
Attaching the cutting blade.
Attaching the safety guard---bent shaft.
Attaching the trimmer head
Replacing trimmer line - bent shaft
Attaching the pruner
Attaching the hedge trimmer attachment
Starting your multi tool
Using your accessories.
Technical Specifications
Fast trouble shooting
Basic maintenance made easy
Maintenance Chart
EC Declaration of Conformity
Sanli products are monitored and enhanced on an on-going basis to comply with
changing
technical standards and requirements. As a result, Sanli reserves the right
to alter design and
specifications at any time without prior notice.
Multi Tool Features.
1.
Fuel tank
2.
Air cleaner
3.
Starter
4.
Housing
5.
Throttle cable
6.
Throttle interlock
7.
Throttle trigger
8.
Engine switch
9.
Operate handle
10.
Harness hook
11.
Handle
14
12.
Shaft
13.
Blade guard
14.
Gear case
15.
Blade
16.
Cutting line spool
17.
Gear case
18.
Blade
19.
Oil tank
20.
Saw chain
21.
Guide bar
22.
Gear case
23.
Connector
12
13
15
16
17
18
19
22
20
21
WARNING! The information contained within this safety section is extremely
important. Personal injury to the user and to others may result if this section
is not read and acted upon at all times.
Tips on Multi Tool Safety.
1.
Before starting your multi tool inspect it carefully to ensure that there are no
loose parts
and that it is in good working order.
2.
Be sure of your footing. Always walk, never run, when operating the multi tool.
3.
Clear the area of any stones, sticks, wire and debris before beginning, and
Always ensure
that you operate your multi tool a safe distance away (over 14
metres) from adults,
children and animals.
4.
Keep hands, feet and clothing away from the multi tool’s moving parts, and
always
wear appropriate footwear (avoid sandals or open shoes).
5.
Never put your hands or feet underneath the guard of the multi tool while the
engine is
running.
6.
Be aware that the machine’s exhaust area and other parts of the multi tool get
very hot
during, and right after use.
7.
Turn off the engine and disconnect the spark plug cap before cleaning,
transporting or making adjustments.
8.
We recommend you avoid trimming when it is raining, or after nightfall.
9.
Do not fill the tank, or start the multi tool indoors, or in a poorly ventilated area, as
exhaust
gases contain poisonous substances and petrol fumes are flammable
and dangerous.
10.
Never open the fuel filter cap, or fill the tank, if the engine is still hot after use.
Please ensure that you securely tighten the petrol cap after filling.
11.
Do not transport the multi tool in a vehicle, if there is any petrol in the tank.
12.
Store fuel and oil in a cool well-ventilated place, away from direct sunlight and
not near gas
cylinders or hot water heater systems.
14.
Sanli recommends that you wear ear protectors, safety goggles and safety boots
when using a
multi tool.
15.
All servicing and repair work under warranty must be carried out by an Authorised
Sanli Dealer,
otherwise the warranty may be void.
WARNING! The information contained within this safety section is extremely
important.
Personal injury to the user and to others may result if this section
is not read and acted
upon at all times.
Attaching the handle
- straight shaft.
Place the upper ergonomic handle in the
desired
position (Fig 1) then while
holding the lateral
handle underneath in
position, insert the screws
and tighten with
the allen key provided.
Insert the attachment shaft into the engine
shaft,
ensure the locator on the engine
shaft meets the
hole on the attachment
shaft (Fig 2).
Fig 1
Fig 2
Tighten handwheel securely. (Fig 3)
Fig 3
Attaching the safety guard
- straight shaft.
While placing the multi tool on the ground,
place
the guard as shown in (Fig 4)
and locate the
screws through the tension
plates as indicated
and tighten screws.
Attaching the cutting blade.
(straight shaft model only).
When heavy duty cutting is required
utilise the cutting blade (Fig 5).
Remove the trimmer bump head
& rotate clockwise.
Then place the cutting
blade as shown
and tighten in anti-clockwise
direction.
Order of components to attach the
cutter blade (Fig 6).
Attaching the safety guard
- bent shaft.
While placing the brushcutter on its back,
clip the
guard onto the shaft lining the
holes up with the
guides see (Fig 7)
then locate the bolt through
the guard and
guide plate as indicated. Place the
washer
over the bolt and tighten nut.
Fig 4
Fig 5
Fig 6
Fig 7
Attaching the trimmer head - bent shaft.
Tighten clockwise the trimmer head. Use the black plastic spanner provided on the
nylon head to
tighten it (Fig 8).
Fig 8
Replacing trimmer line –
bent shaft.
Take approximately 4-5 metres of 2.0-
2.4mm diameter trimmer line, fold in half to
make a loop. Hold the spool as shown
in (Fig
9) and hook the loop onto the divider plate
as shown and wind the
line, one on either
side of the divider
plate.
Wind both lines anti-clockwise on both
sides
of spool ensuring that both lines
remain in
their respective channels as shown in
(Fig 10).
Fig 9
Fig 10
In order to stop the line from
unraveling, slip
each end into the lugs
on the bottom edge
of the spool, shown in
(Fig 11).
Fig 11
Insert ends of the trimmer line through the
holes in
side of the spool casing and place
the
spool into the centre of the casing (Fig
12).
When in position pull the ends further
out of
the casing, then return the lid,
click into
place and return to hub.
Attaching the pruner
1.
Remove the cap on the end of
shaft.
2.
Remove the screw on
the end of the
gear case.
3.
Insert the the shaft into end of the
gear case.
4.
Line up the hole on the end of
the gear case into which the screw
is to
be inserted with the hole on
the shaft &
tighten the screw firmly. (Fig 13)
Fig 12
Fig 13
5.
Using an Allen key. Tighten the bolt
provided, to fix the mechanism into
place (Fig 14).
Filling up with oil
Fill the oil tank with chainsaw oil before
using.
(Fig 15)
Fig 14
Attaching the hedge trimmer
attachment.
1.
Remove the screw from
the end of the
hedgetrimmer
a
ttachment.
2.
Insert the end of the shaft into the
hedgetrimmer head.
3.
Line up the hole on the end of the
hedgetrimmer head with
the hole on the shaft.
4.
Using an Allen key, tighten the bolts
provided
to fix the hedgetrimmer attachment into place.
(See Fig 16 & Fig 17)
Fig 15
Fig 16
Fig 17
Table des matières
