Samsung IES4028F Manuel de programmation

iES4028F/4028FP/4024GP

iES4028F

iES4028FP

iES4024GP

E082008/ST-R03

149100041800A

149100040200A

149100041700A

149100000020A

iii

This manual is proprietary to SAMSUNG Electronics Co., Ltd. and is protected

by copyright.

No information contained herein may be copied, translated, transcribed or

duplicated for any commercial purposes or disclosed to third parties in any form

without the prior written consent of SAMSUNG Electronics Co., Ltd.

TRADEMARKS

Ubigate iES4028F, Ubigate iES4028FP and Ubigate iES4024GP are registered

trademarks of SAMSUNG Electronics.

All other company and product names may be trademarks of the respective

companies with which they are associated.

This manual should be read before the installation and operation, and the

operator should correctly install and operate the product by using this manual.

This manual should be read before the installation and operation, and the

operator should correctly install and operate the product by using this

manual.

This manual may be changed for the system improvement, standardization

and other technical reasons without prior notice.

For further information on the updated manual or have a question for the

content of manual, contact the homepage below.

Homepage: http://www.samsungnetwork.com

For A/S and Tech. support: http://www.samsungnetwork.com

For Manual: http://www.samsungdocs.com

This page is intentionally left blank.

About This Guide

Purpose

This guide gives specific information on how to operate and use the management

functions of the switch.

Audience

The guide is intended for use by network administrators who are responsible for operating

and maintaining network equipment; consequently, it assumes a basic working

knowledge of general switch functions, the Internet Protocol (IP), and Simple Network

Management Protocol (SNMP).

Conventions

The following conventions are used throughout this guide to show information:

Note: Emphasizes important information or calls your attention to related features or

instructions.

Caution: Alerts you to a potential hazard that could cause loss of data, or damage the

system or equipment.

Warning: Alerts you to a potential hazard that could cause personal injury.

Related Publications

The following publication details the hardware features of the switch, including the

physical and performance-related characteristics, and how to install the switch:

The Installation Manual

Also, as part of the switch’s software, there is an online web-based help that describes all

management related features.

Revision History

This section summarizes the changes in each revision of this guide.

August 2008 Revision

This is the third revision of this guide. It combines information for the Ubigate iES4028F,

iES4028FP and iES4024GP. This guide is valid for software release v1.1.0.14. Other than

the addition of information about the iES4024GP, it also includes the following updated

and additional information in the indicated tables or sections:

• Table 1-1, “Differences in Switch Models,” on page 1-1.

• Single image and dual image support in “Managing Firmware” on page 3-21.

• Access Level attribute in “Configuring User Accounts” on page 3-58.

• MAC Address Aging attribute in “Configuring the MAC Authentication Reauthentication

Time” on page 3-103.

• SYM and FC attributes in “Configuring Interface Connections” on page 3-130.

• “Setting Multicast Storm Thresholds” on page 3-149.

• “Setting Unknown Unicast Storm Thresholds” on page 3-150.

• Updated descriptive text under “Power Over Ethernet Settings” on page 3-157.

• Updated descriptive text under “Configuring Port PoE Power” on page 3-160.

• Command Usage notes in “Switch Clustering” on page 3-273.

• “show memory” on page 4-33.

• “show gvrp statistics” on page 4-251.

• “clear gvrp statistics” on page 4-252.

• Updated Command Usage section under “power inline priority” on page 4-216.

July 2008 Revision

This was the second revision of this guide. It combines information for the Ubigate

iES4028F and iES4028FP. This guide is valid for software release v1.1.0.13. Other than

the addition of information about the iES4028F, it also includes the following updated and

additional information in the indicated tables or sections:

• Table 1-2, “Key Features,” on page 1-2.

• “Description of Software Features” on page 1-3.

• Table 1-3, “System Defaults,” on page 1-7.

• “Dynamic Configuration” on page 2-5.

• “Managing System Files” on page 2-8.

• “Saving Configuration Settings” on page 2-9.

• “Configuring Power over Ethernet” on page 2-10.

• VLAN Learning under “Displaying Bridge Extension Capabilities” on page 3-16.

• Removal of default IP address under “Setting the Switch’s IP Address” on page 3-17.

• Change to jumbo frame size under “Enabling Jumbo Frames” on page 3-20.

• “Managing Firmware” on page 3-21.

• Command Usage and Command Attributes under “Specifying Trap Managers and Trap

Types” on page 3-43.

• NAS IP Address under “Configuring Local/Remote Logon Authentication” on page 3-59.

• Size of Secret Text String under “Configuring Encryption Keys” on page 3-64.

• Private Password under “Replacing the Default Secure-site Certificate” on page 3-78.

• Public Key Type under “Importing User Public Keys” on page 3-84.

• Command Usage under “Configuring Port Security” on page 3-97.

• Notes under “Web Authentication” on page 3-98.

• Note under “Network Access (MAC Address Authentication)” on page 3-102.

• Guest VLAN, Dynamic VLAN, and removal of Dynamic QoS under “Configuring MAC

Authentication for Ports” on page 3-104.

• Removed Security, Network Access, Port Link Detection Configuration web page.

• Command Usage under “Access Control Lists” on page 3-108.

• Removed references to static bindings for DHCP Snooping under “DHCP Snooping” on

page 3-116.

• Command Usage and Command Attributes under “Configuring VLANs for DHCP

Snooping” on page 3-118.

vii

• Command Usage and Command Attributes under “Configuring the DHCP Snooping

Information Option” on page 3-118.

• Command Usage under “Configuring Ports for DHCP Snooping” on page 3-120.

• Command Usage under “IP Source Guard” on page 3-123.

• Command Usage under “Configuring Static Binding for IP Source Guard” on page

3-125.

• Command Usage and Command Attributes under “Configuring Interface Connections”

on page 3-130.

• “Configuring Parameters for LACP Groups” on page 3-141.

• Flooding Behavior Field Attributes under STA - “Displaying Global Settings” on page

3-168.

• Spanning Tree BPDU Flooding Command Attribute under STA - “Configuring Global

Settings” on page 3-171.

• BPDU Flooding Field Attribute under “Displaying Interface Settings” on page 3-175.

• Admin Path Cost Command Attribute under “Configuring Interface Settings” on page

3-178.

• Forwarding Tagged/Untagged Frames under “IEEE 802.1Q VLANs” on page 3-187.

• Untagged Command Attribute under “Adding Static Members to VLANs (VLAN Index)”

on page 3-195.

• Ingress Filtering Command Attribute under “Configuring VLAN Behavior for Interfaces”

on page 3-198.

• Mode Access Command Attribute under “Configuring VLAN Behavior for Interfaces” on

page 3-198.

• 802.1Q Tunnel Status Command Attribute under “Enabling QinQ Tunneling on the

Switch” on page 3-204.

• “Traffic Segmentation” on page 3-206.

• Removed Isolated VLAN option from “Private VLANs” on page 3-209.

• Introduction and Command Usage under “Protocol VLANs” on page 3-214.

• Command Usage under “Configuring the Protocol VLAN System” on page 3-216.

• Field Attributes under “Displaying LLDP Local Device Information” on page 3-222.

• Field Attributes under “Displaying LLDP Remote Port Information” on page 3-225.

• Field Attributes under “Displaying LLDP Remote Information Details” on page 3-226.

• Introduction and Field Attributes under “Displaying Device Statistics” on page 3-228.

• Field Attributes under “Displaying Detailed Device Statistics” on page 3-229.

• Introduction, Command Usage and Command Attributes under “Selecting the Queue

Mode” on page 3-234.

• Introduction under “Setting the Service Weight for Traffic Classes” on page 3-234.

• “Mapping Layer 3/4 Priorities to CoS Values” on page 3-235.

• Action Command Attribute under “Creating QoS Policies” on page 3-242.

• Introduction under “Multicast Filtering” on page 3-251.

• Introduction and Command Usage under “Enabling IGMP Immediate Leave” on page

3-255.

• New Multicast Address Range List Command Attribute under “Configuring IGMP Filter

Profiles” on page 3-262.

• Command Usage and MVR Running Status Command Attribute under “Configuring

Global MVR Settings” on page 3-266.

viii

• Command Usage and Command Attributes under “Configuring MVR Interface Status”

on page 3-270.

• Command Usage under “Switch Clustering” on page 3-273.

• Introduction under “UPnP” on page 3-277.

• Command Usage under “jumbo frame” on page 4-33.

• Command Usage under “copy” on page 4-35.

• Syntax under “show log” on page 4-55.

• Using Switch Clustering under “Switch Cluster Commands” on page 4-73.

• Introduction under “UPnP Commands” on page 4-77.

• “Debug Commands” on page 4-80.

• Syntax for “radius-server host” on page 4-105.

• Introduction, Default Setting and Command Usage under “radius-server attribute 4” on

page 4-107.

• Syntax for “radius-server key” on page 4-107.

• Syntax for “tacacs-server host” on page 4-110.

• Syntax for “tacacs-server key” on page 4-111.

• Introduction for “aaa group server” on page 4-114.

• Syntax for “show accounting” on page 4-122.

• “ip telnet server” on page 4-126.

• Authentication section of Configuration Guidelines under “Secure Shell Commands” on

page 4-127.

• Command Usage under “dot1x re-authenticate” on page 4-140.

• Command Usage under “dot1x re-authentication” on page 4-140.

• Command Usage under “port security” on page 4-149.

• Introduction under “Network Access (MAC Address Authentication)” on page 4-150.

• Removed network-access dynamic-qos, network-access link-detection,

network-access link-detection link-down, network-access link-detection link-up, and

network-access link-detection link-up-down commands from “Network Access (MAC

Address Authentication)” on page 4-150.

• Removed web-auth login-fail-page-url, web-auth login-page-url, and web-auth

• Command Usage under “ip dhcp snooping information option” on page 4-169.

• Removed reference to static DHCP Snooping entries from Command Usage under “ip

source-guard” on page 4-172 and “ip source-guard binding” on page 4-174.

• Introduction, Syntax and Command Usage under “permit, deny (Extended ACL)” on

page 4-179.

• Removed Command Usage from “ACL Information” on page 4-187.

• Command Usage under “speed-duplex” on page 4-189.

• “media-type” on page 4-193.

• “giga-phy-mode” on page 4-194.

• Default Setting under “switchport packet-rate” on page 4-195.

• “lacp active/passive” on page 4-209.

• Software Version parameter in Table 4-60, “show power mainpower parameters,” on

page 4-218.

• Syntax and Command Usage under “port monitor” on page 4-219.

• “spanning-tree system-bpdu-flooding” on page 4-231.

• Syntax and Default Setting under “spanning-tree cost” on page 4-237.

• “spanning-tree port-bpdu-flooding” on page 4-240.

• Syntax and Default Setting under “spanning-tree mst cost” on page 4-244.

• Syntax for “switchport mode” on page 4-257.

• Removed note under “switchport ingress-filtering” on page 4-258.

• Removed note under “switchport allowed vlan” on page 4-260.

• Command Usage under “switchport allowed vlan” on page 4-260.

• Syntax for “show vlan” on page 4-262.

• Limitations for QinQ under “Configuring IEEE 802.1Q Tunneling” on page 4-263.

• Command Usage under “switchport dot1q-tunnel mode” on page 4-264.

• “Configuring Port-based Traffic Segmentation” on page 4-267.

• Removed references to isolated VLAN option from “Configuring Private VLANs” on

page 4-271 and related commands which had supported this option.

• Removed switchport private-vlan isolated command.

• Command Usage under “switchport voice vlan” on page 4-282.

• Command Usage under “queue mode” on page 4-308.

• Removed queue bandwidth command.

• Configuration guidelines under “Quality of Service Commands” on page 4-316.

• Introduction and Syntax for “set” on page 4-320.

• Command Usage under “mvr (Global Configuration)” on page 4-341.

• Command Usage under “mvr (Interface Configuration)” on page 4-343.

• Command Usage under “ip default-gateway” on page 4-348.

• General Security Measures under “Software Specifications” on page A-1.

• Updated entries for Standards under “Software Specifications” on page A-1.

• Updated entries for Management Information Bases under “Software Specifications” on

page A-1.

April 2008 Revision

This was the first revision of this guide for the Ubigate iES4028FP.

This page is intentionally left blank.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Samsung Routeur réseau

Samsung

Samsung Ubigate iBG1000 Manuel utilisateur

Samsung

Samsung DIR-640LA1 Manuel utilisateur

Samsung

Samsung iES4028FP Manuel utilisateur

Samsung

Samsung Ubigate iBG1000 Manuel utilisateur

Samsung

Samsung SmartThings Wifi ET-WV525 Manuel utilisateur

Samsung

Samsung Connect Home Pro ET-WV530 Manuel utilisateur

Samsung

Samsung MWR-SH00N Manuel utilisateur

Samsung

Samsung Connect Home Pro ET-WV520 Manuel utilisateur

Samsung

Samsung 5G CPE Manuel utilisateur

Samsung

Samsung 5G CPE Manuel utilisateur

Samsung

Samsung SmartThings Wifi ET-WV525 Manuel utilisateur

Samsung

Samsung DIR-518L Manuel utilisateur

Samsung

Samsung Techwin SPN-10050 Manuel utilisateur

Samsung

Samsung OFFICESERV 500 Series Manuel utilisateur

Samsung

Samsung Ubigate iBG2006 Manuel utilisateur

Samsung

Samsung iES4028FP Manuel utilisateur

Samsung

Samsung Ubigate iBG2016 Manuel de programmation

Samsung

Samsung Ubigate iBG1003 Manuel utilisateur

Samsung

Samsung DCS-Compact II Manuel utilisateur

Samsung

Samsung AHT-E300 Manuel utilisateur

Samsung

Samsung MagicLAN SWL-2200U Manuel utilisateur

Samsung

Samsung SCC-RC130 Manuel utilisateur

Samsung

Samsung Connect Home Pro ET-WV532 Manuel utilisateur

Samsung

Samsung Connect Home Pro ET-WV533 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité

Samsung iES4028F Manuel de programmation

Manuels Routeur réseau populaires d'autres marques