Samsung SPO-100 Manuel utilisateur

PoE Function IP Extender

User Manual SPO-100

Trademark

is the registered logo of Samsung Techwin Co., Ltd.

The name of this product is the registered trademark of Samsung Techwin Co., Ltd.

Other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall

be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.

Disclaimer

Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no

formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own

responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.

Design and specifications are subject to change without prior notice.

PoE Function IP Extender

User Manual

English _3

overview

Please read the following recommend safety precautions carefully.

yPlease do not install the device in a location where the temperature gets higher than

50 °C or lower than -10°C, nor in a location where there is a lot of rain or snow or

where humidity is high, nor in a location that is exposed to oil or gas, nor in a location

that experiences vibration or shocks, nor in an outside area, nor exposed to direct

light, nor in a location close to strong magnetism, high frequency (RF) or power

cables. Failure to comply may cause performance degradation or malfunction.

yDo not disassemble the product or introduce a foreign substance such as the metal.

yInstall only after checking the specifications and operation manual.

yNever connect a device of more than rated capacity as it can cause a fire.

(PTZ cameras, in particular, are prohibited as they consume too much power.)

yThe operating conditions appropriate for this device are -10°C to 50°C. Be cautious

when you use it commonly indoors or outdoors.

yBe careful not to mix up the wiring during installation. Refer to the UTB cable wiring

manual.

yMake sure that the IP camera supports PoE type B before using it.

yCaution is necessary as strong impact or vibration can cause a device malfunction.

ySmoke or a smell coming from the device while it is operating can lead to a fire or

electric shock.

In that case, pull off the power cable immediately and contact the place of purchase

or A/S center and receive counseling by the technical staff.

yThe UTP cable is UTP (unshielded twisted pair) indoor cable and should not be used

outdoors but STP (shielded twisted pair) is recommended for installation outdoors. If the

UTP cable is used outdoors, problems can occur with the product such as an abnormal

voltage being applied to the cable due to lightning.

yRefer to the operating manual regarding other problems or questions and contact

the A/S center if you need help from technical staff.

overview

4_ overview

CONTENTS

OVERVIEW

4Contents

5Product Introduction

5Product Features

5Application

6What’s Included

6Connecting the UTP cable

7At a Glance

INSTALLATION &

CONNECTION

9Connecting with other Device

APPENDIX

12 Specification

13 Product Overview

English _5

PRODUCT INTRODUCTION

This device is a single channel UTP (Ethernet Data + PoE) extender and has the built-in

power supply function (PoE) to supply the power to the camera through the UTP cable.

To overcome problems caused by the short transmission distance (100m or less) of

network equipment, it can be installed in the UTP cable section between the camera and

PoE hub, extending the transmission distance to more than 100m. Since power can be

supplied to the IP camera with PoE, the construction cost can also be saved.

PRODUCT FEATURES

ySimultaneous transmission of power and IP data to the UTP cable (CAT.5)

ySupport of TCP speed of 100Mbps Full Duplex

yEach time this device is installed, the maximum transmission distance for

Ethernet data is extended by more than 100m.

M`The number of SPO-100 systems that can be added is limited by the rated capacity of

the IP camera.

yA camera with up to 11.7W power consumption can be connected when

power is supplied through the PoE HUB.

M`Refer to the maximum extensible distance table on page11.

yBuilt-in surge-protection circuit for safety

APPLICATION

yApplication for conventional IP type or Mega Pixel camera

yArea in which an IP camera is installed within 100m of a Web Viewer

yExtended connection between the IP systems (PC or NVR)

overview

6_ overview

WHAT’S INCLUDED

Please check if your network video encoder and accessories are all included in the

product package.

Appearance Item Name Quantity

Ethernet extender 1

User Manual 1

CONNECTING THE UTP CABLE

Use the cable after checking the 4P UTP cable wiring method.

Scheme of TIA / EIA 568B

a c e gb d f h

aOrange+White Tx + eBlue+White DC 48V

bOrange Tx - fGreen Rx –

cGreen+White Rx + gBrown+White GND

dBlue DC 48V hBrown GND

J `Caution is required when working with the RJ-45 jack as above.

English _7

AT A GLANCE

Front Side

Item Description

aNetwork connection

terminal

The connection terminal of the IP camera, which uses PoE,

acts as a power supply and data port .

LED Status Status indication

YELLOW On PoE IN

Off No Power

GREEN

On Linked

Flash Data Active

Off Not Linked

overview

8_ overview

Rear Side

Item Description

aNetwork connection

terminal

It receives power through the PoE switching hub / PoE injector /

NVR connection terminal and transmits camera data to the NVR.

LED Status Status indication

YELLOW On 100Mbps Linked

Off 10Mbps Linked

GREEN

On Linked

Flash Data Active

Off Not Linked

J `Take care regarding to get the production connection direction right.

When connecting a PoE hub (standard type), it must be connected to the rear port RJ-45

connector in order for the PSE system to recognize it.

English _9

installation & connection

CONNECTING WITH OTHER DEVICE

Connecting the camera

Connect the [CAMERA] terminal of the device and video output terminal of the

camera.

Camera

installation & connection

10_ installation & connection

Connecting a product

Using a switching hub, multiple devices can be connected within the available

power range (6.3W - 11.7W) of the SPO-100.

Supplying the power through the switching hub with built-in PoE function

Installing more than two SPO-100 systems

J `The maximum extensible distance depends on the rated capacity of the IP camera,

the precise characteristics of the cable, the cable type, and the number of added

SPO-100s.

`Network link-time can increase as the number of systems increases.

Camera

Extender Extender PoE Switching HUB

(Standard PoE)

Camera Extender

PoE Switching HUB

(Standard PoE)

Table des matières

Autres manuels Samsung Extenseur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Samsung

Samsung Verizon 4G LTE Network Extender Manuel utilisateur

Samsung

Samsung 4G LTE Network Extender 2 Manuel utilisateur

Samsung

Samsung SCS2U3100VER Manuel utilisateur

Samsung

Samsung Verizon SLS-BU103 Manuel utilisateur

Samsung

Samsung Verizon SLS-BU102 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Samsung

Samsung SCS-2U01 Manuel utilisateur

Samsung

Samsung Verizon SLS-BU103 Mode d’emploi

Samsung

Samsung EP68-00520A Manuel utilisateur

Samsung

Samsung SCS-26UC2 Manuel utilisateur

Samsung

Samsung Verizon Wireless Network Extender Manuel utilisateur

Samsung

Samsung Verizon 4G LTE Network Extender Manuel utilisateur

Samsung

Samsung SCS2U01VER Manuel utilisateur

Samsung

Samsung Verizon Wireless Manuel utilisateur

Samsung

Samsung SLS-BU10G Manuel utilisateur

Samsung

Samsung SEB-100 Mode d’emploi

Samsung

Samsung UbiCell Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Manuel utilisateur