Salter Brecknell B220 Manuel utilisateur
B220
User Instructions
Brisch number 76103-383 Issue 1 11/07/01
ENGLISH *76103-383*
Counting Scale
Table of Contents
Warnings 1
Cleaning the scale 1
Installation 1
Switching the scale on 2
Bleeps 3
Testing the display/Selecting sleep mode 3
Error messages 3
4
Zeroing the scale 4
Using the clear key 4
Clearing a numeric entry 4
4
Creating a tare 4
Creating a keyboard entered tare 4
Cancelling a tare 5
5
Fast sampling 5
Normal sampling 6
Re-sampling 6
Keyboard entered item weights 6
Viewing the item weight 6
Clearing the item weight 6
7
Setting an item limit 7
Viewing the item limit 7
Clearing the item limit 7
Forward counting 7
Reverse counting 7
Batch counting 8
Using the scale
Using tares
Sampling
Counting
i
Batch counting 8
Totalising 8
9
Programming a PLU hot key 9
Programming a keyboard PLU 9
Using a PLU hot key 9
Using a keyboard entered PLU 9
Clearing a PLU hot key 9
Clearing a keyboard entered PLU 10
Clearing a keyboard entered PLU 10
User Calibration Adjustment 10
To Cancel A User Calibration Adjustment 10
Weights For Calibration Adjustment 10
11
Zero Indicator 11
Zero Tracking 12
Automatic Zero Self Balance 12
Standard Filter 12
Intelligent Filter Setup 12
Weight Steady 12
Switching the bleeper alarm on/off 13
Switching the keyboard bleeper on/off 13
Weight limit bleep 13
Error bleeper 13
Changing the bleeper volume 13
Changing the backlight time 13
Changing the sleep time 13
Using PLUs
Management mode
ii
Changing the duration of a ‘Long’ press 14
Changing the minimum sample weight 14
Changing the manual re-sampling range 14
Changing the automatic re-sampling range 14
14
Changing a PLU item weight 14
Changing a PLU tare 15
Protecting a PLU 15
16
17
Changing PLUs
Declaration of Conformity non-approved
Declaration of Conformity approved
iii
Warnings
Cleaning the scale
Installation
For your protection, all mains (110V or 230V) equipment used where
damp or wet conditions may occur, must be supplied from a correctly
fused source and protected by an approved RCD to BS7071 or BS7288
or IEC1008-2-2 BS EN 61008:1995. IF IN DOUBT SEEK ADVICE
FROM A QUALIFIED ELECTRICIAN.
To avoid the possibility of electric shock or damage to the machine,
always isolate from the mains power supply before carrying out any
routine maintenance.
Harsh abrasives, solvents, scouring cleaners and alkaline cleaning
solutions, such as washing soda, should not be used especially on the
display windows. Under no circumstances should you attempt to wipe
the inside of the machine.
The outside of the machine may be wiped down with a clean cloth
moistened with water containing a small amount of washing up liquid.
Make sure that the work surface is firm, steady and free from vibration
and draughts.
To avoid the risk of RSI (Repetitive Strain Injury) it is important to
ensure that the machine is placed on a surface which is ergonomically
satisfactory to the user. In cases where usage is prolonged EN614-1
recommends frequent breaks for the user.
1
Switching the scale on
Connecting to the mains - Plug the adaptor lead into the scale,
replace the cover and weighplate and then plug the adaptor into the
power supply.
: Do not use the mains adaptor if it is damaged.Warning
Using batteries
Caution:
- Plug the battery pack into the scale and place the
pack into the recess. Replace the cover and weighplate.
To avoid damage to the scale caused by leaking batteries,
remove flat or damaged batteries immediately.
When you see the symbol flashing on the display, then you must
either replace the batteries (or recharge the rechargeable batteries).
NiCad
Using a rechargeable battery pack
Recharging the battery pack
Note:
- Plug the rechargeable
battery pack into the scale and place the pack into the recess. Replace
the cover and weighplate.
- Plug in the mains cable to the
bottom of the scale, then switch on using the mains ON/OFF switch.
You can still use the scale while the battery is being charged.
2
Bleeps
Short press (Press once) Long press (Press and hold)
Testing the display/Selecting sleep mode
1
101d
0-6-0
Service
information:
SLEEP
Short
press x 2
Short
press
Long
press
Short
press
Error messages
If a persistent error message appears or the scale locks up,
disconnect then reconnect the scale to the power supply. If
the scale remains inoperative, contact your authorised
service agent.
E 0 Disconnect then reconnect the scale to the power supply.
E 5 Disconnect then reconnect the scale to the power supply.
E 10 Battery failure. Recharge or replace the batteries.
E 11 Power supply voltage is too high.
E 15 Contact your authorised service agent.
E 20 Weight error. Remove all items from the weighplate and press
the clear key (long press).
E 100 Invalid PLU contents. Re-program the PLU.
E 101 Transaction failed. Remove all items from the weighplate and
press the clear key (long press).
Error codes:
E 30 Contact your authorised service agent.
E 35 Contact your authorised service agent.
E 102 PLU write failed. The PLU is protected in management mode
(see Page 15).
E 103 Tare failed. Remove all items from the weighplate and press the
clear key (long press).
E30
Temporary
error
Weight
unsteady
Balance
failed
Under
range
Over
range
3
Wake up:
Using the scale
Zeroing the scale
Make sure that the scale is at zero before weighing.
Short
press
0.000
Using tares
Creating a keyboard entered tare
0.000
CE
Long
press
Using the clear key
To clear all active PLUs, tares and item weights:
Clearing a numeric entry
Enter
value
1.26 1.2 0
CE
Short
press
To clear the
last entry:
CE
Long
press
To clear the
entire entry:
Creating a tare
Short
press
TT
Tare value
(kg)
T
Short
press
T
0.150
0.000
NET
PT
4
Cancelling a tare
T
Short
press
T
-0.150
NET
0.000
Sampling
The method that you use to sample will depend on whether the items
that you intend to count are high or low value and whether the items
vary slightly in weight:
Small
Sample weight*
Large
Sample weight*
Gold
coins
Nuts/
bolts
Currency
notes
Plastic
Mouldings Weight
variation
Value
Normal
sampling
Fast
sampling
*See management mode.
When sampling items that have a large weight variation it is advisable
to use a large sample size and either manual or automatic re-sampling.
Fast sampling
The greater the number of items used to sample with, the more
accurate the scale will be.
Short
press
Short
press
=15 Short
press
1.0
1.345
10
Add 15 The scale is now
ready for counting.
Note: If the minimum sample weight in management mode is active
(see Page 14), then If the sample weight is too light, the scale will ask
you to put some more items onto the scale:
5
Autres manuels pour B220
2
Table des matières
Autres manuels Salter Brecknell Échelle
Salter Brecknell
Salter Brecknell B220 Manuel utilisateur
Salter Brecknell
Salter Brecknell TME0221 Instructions d'installation
Salter Brecknell
Salter Brecknell S122 Manuel utilisateur
Salter Brecknell
Salter Brecknell SBI-100 Manuel utilisateur
Salter Brecknell
Salter Brecknell 302 BP Series Manuel d'utilisation et d'entretien
Salter Brecknell
Salter Brecknell PS250 Manuel utilisateur
Salter Brecknell
Salter Brecknell LPS-400 Manuel utilisateur
Salter Brecknell
Salter Brecknell B 130 Manuel utilisateur
Salter Brecknell
Salter Brecknell S122 Manuel utilisateur
Salter Brecknell
Salter Brecknell 405 Manuel utilisateur
Salter Brecknell
Salter Brecknell BS150 Guide de dépannage
Salter Brecknell
Salter Brecknell MS-20 Manuel utilisateur
Salter Brecknell
Salter Brecknell B 120 Manuel utilisateur
Salter Brecknell
Salter Brecknell SPC Series Manuel utilisateur
Salter Brecknell
Salter Brecknell EG1500 Manuel d'installation
Salter Brecknell
Salter Brecknell Pegasus Floor Scale Manuel utilisateur
Salter Brecknell
Salter Brecknell CS Manuel utilisateur
Salter Brecknell
Salter Brecknell 405 Manuel utilisateur
Salter Brecknell
Salter Brecknell HTS-150 Manuel utilisateur
Salter Brecknell
Salter Brecknell B220 Manuel utilisateur
