Salem Master Pro 6220G Guide de configuration rapide

2-Cycle Chain Saw 6220G /5820G

Assembly&Use Manual

Introduction

Operator's manual

Product overview

12 11

15 17

1. Starter handle

2. Air ﬁlter cover

3. Front handle

4. Cylinder cover

5. Chain brake

6. Muﬄer

7. Bar nose sprocket

8. Right hand guard

9. Trigger

10.Trigger lockout

11.Pumper spike

12.Guide bar

13.Saw chain

14.Pumper spike screw

15.Chain oil tank

16.Starter cover

17.Fuel tank

18.Switch button

19.Rear handle

20.Visible fuel tank

21.Choke control

22.Clutch cover

23.Guide-bar nuts

24.Chain tensioning screw

25.Guide-bar cover

26.Combination tool

282930

27.Fuel mixture container

28.Hex wrench(big/small)

29.Idle Screwdriver

30.Round ﬁle diameter

READ ALL INSTRUCTIONS BEFORE OPERATING

Assembly

WARNING: Read and understand

the safety chapter before you

assemble the product.

To assemble the guide bar and saw

chain

Pull the chain brake back oﬀ

1. Install bumper spike

Bumper spike

2. Remove the guide bar nuts and the

Clutch cover. Remove the bolt protection

3. Put the guide bar above the bar bolts.

Steer the guide bar to under clutch

position.

Bolt protection

Guide-bar nuts

Clutch cover

Guide

Bar bolts

Guide Bar Bolts

Clutch

4. Put on protective chainsaw gloves.

Drive

Sprocket

Clutch

5. Lift the saw chain above the drive sprocket

Engage chain in the groove on the guide bar.

Start on the top edge of the guide bar.

Bar Groove

Chain Drive

Links

6. Make sure that the edges of the cutting

links are turned forward on the top edge of

the guide bar.

7. Assemble the clutch cover and steer the

chain adjuster pin to the hole in the guide

bar.

8. Make sure that the drive links of the saw

chain ﬁt correctly on the drive sprocket.

Also make sure that the saw chain is

correctly engaged in the groove in the

guide bar.

9. Tighten the guide bar nuts with your

ﬁngers.

Chain-tensioning

Pin Hole

Drive

Sprocket

Chain Drive

Links

Chain

Rotation

Cutters

Clutch

10.Tighten the saw chain by turning the chain

tensioning screw clockwise with the

combination wrench

. Tighten the saw chain until it does not sag

from below the guide bar, but you can turn

Chain-tensioning Screw

11.Hold up the end of the guide bar and

tighten the bar nuts with the combination

wrench.

• Examine the chain tension frequently

after you assemble a new saw chain

and until the saw chain has been run-in.

• Examine the chain tension regularly.

Correct chain tension results in good

cutting performance and a long life.

ADJUSTING THE CHAIN TENSION

CAUTION:

The chain must be

tensioned whenever the ﬂats on the

1. Stop the engine.

drive links hang out of the bar groove.

Check for proper chain tension before starting

the unit and periodically during operation.

2. Sightly loosen the guide bar nuts.

3 . Tighten /loosen the saw chain by

tensioning screw

turning the chain

with the combination wrench.

4. lift the tip of the guide bar up to check

for proper tension

5. Hold the tip of the guide bar up securely

tighten the guide bar nuts .

If not will bent tensioning screw

NOTE: A new chain tends to stretch.

Check the chain tension frequently

and tighten as required .

Operation

WARNING: Read and understand the safety chapter before you

operate the product.

To use fuel

Fuel mixture ratio

The fuel mixture ratio for the gasoline and two-

cycle engine oil is 25:1

To make the fuel mixture

1. Determine the correct quantity of gasoline

and engine oil (mixture ratio 25:1). Do not

make more than 30 days quantity of fuel

mixture. .

2. Add half of the gasoline quantity to a clean

fuel container with an antispill valve.

CAUTION: Do not use gasoline

with more than 10% ethanol

concentration (E10). This can

cause damage to the product.

UNLEADED GAS 2 CYCLE OIL

1 GALLON US

(3.8 LITERS)

5.1 FL. OZ.

(152 ml)

1 LITER 40 ml

WARNING: Gasoline is extremely ﬂammable. Ignited vapors may explode. Always stop the engine

and allow it to cool before ﬁlling the fuel tank. Do not smoke while ﬁlling the tank. Keep sparks and open

ﬂames at a distance from the area.

WARNING: Remove the fuel cap slowly to avoid injury from fuel spray. Never operate the unit without

the fuel cap securely in place.

CAUTION: For proper engine operation and maximum reliability, pay strict attention to the oil and fuel

mixing instructions on the 2-cycle oil container. Using improperly mixed fuel can severely damage the engine.

WARNING: Add fuel in a clean, well-ventilated outdoor area. Wipe up any spilled fuel immediately.

Avoid creating a source of ignition for spilt fuel. Do not start the engine until fuel vapors dissipate.

MIXING RATIO - 25:1

25:1

Gasoline

2-cycle oil

Fuel Tank

Chain oil tank

Visible fuel tank

CAUTION: Do not use gasoline

with an octane number less than

90 RON (87 AKI). This can cause

damage to the product.

Note: Use gasoline with a higher octane

number if you frequently use the product at

continuously high engine speed.

3. Add the full quantity of the two-cycle engine

oil to the fuel container.

CAUTION: Always use air-

cooled two-cycled engine oil of

high quality. Other oils can cause

damage to the product.

4. Shake the fuel mixture to mix the contents.

5. Add the remaining gasoline quantity to the

fuel container.

6. Shake the fuel mixture to mix the contents.

7. Fill the fuel tank of the product with the fuel

mixture. See

To use fuel on page 14

To ﬁll the fuel tank

1. Make sure that the fuel mixture is correct

and that the fuel mixture is in a fuel

container with an antispill valve.

2. If fuel is on the container, remove the

unwanted fuel and let the container dry.

3. Make sure that the area near the fuel tank

cap is clean.

4. Remove the fuel tank cap.

5. Shake the fuel container before you add

the fuel mixture to the fuel tank.

6. Put back the fuel tank cap.

To lubricate the saw chain

The product has an automatic lubrication

system. The saw chain oil tank and the fuel

tank are designed so that the fuel runs out

before the saw chain oil. This safety feature

requires that the correct chain oil is used and

that the instructions are obeyed.

1. Use vegetable-based saw chain oil or a

standard chain oil.

2. Make sure that the area near the cap of the

saw chain oil tank is clean.

3. Remove the cap of the saw chain oil tank.

4. Fill the saw chain oil tank with the

recommended saw chain oil.

5. Put back the cap of the saw chain oil tank.

To start and stop

Before you start the engine

• Examine the product for missing, damaged,

loose or worn parts.

• Examine the nuts, screws and bolts.

• Examine the air ﬁlter.

• Examine the trigger lockout and the trigger

for correct operation.

• Examine the stop switch for correct

operation.

• Examine the product for fuel leaks.

• Examine the saw chain sharpness and

tension.

To start a cold engine

1. Move the front hand guard forward to

engage the chain brake.

2.Open the switch button(1 open /0 stop).

switch button

3. Pull the choke control out fully.

4. Hold the body of the product on the ground

with your left hand.

5. Put your right foot through the rear handle.

6. Pull the starter rope handle slowly with your

right hand until you feel some resistance.

7. Pull the starter rope handle with force.

CAUTION:

Note: Do not pull the throttle trigger when

you start the engine.

8. Continue to pull the starter rope handle

until the engine starts or tries to start (pull

max 5 times).

9. If the engine starts or tries to start, push the

choke control back fully position.

10.Continue to pull until the engine starts.

Choke control

11.Hold the rear handle with your right hand

and the front handle with your left hand.

12.Immediately pull the front hand guard

rearward in the direction of the front handle

to disengage the chain brake.

Don’t pull the rope to its limit .

As this may cause the rope to break.

Don’t let the rope snap back.

Hold the handle and let the rope rewind slowly

There is no need to pull the rope briskly

There is no harsh resistance when pulling

Note: The chain will move.

13.Run 20-30 seconds at elevated idle speed.

14.Pull the throttle trigger slowly but fully for

8-10 seconds, then release.

15.Run 10 seconds at normal idle speed.

16.Pull the throttle trigger slowly but fully for 5

seconds to check acceleration, then

release.

17.Use the product.

Cylinder

Table Fuel

When you pull the trigger-it turns oﬀ.

The engine doestn’t start

1. Examine the switch button position(page18)

2. Examine the choke position(step 9 )

3. Examine the muﬄer and cylinder

feel fuel in the smoke hole with you ﬁngers

Cylinder cleaning

a. Turn oﬀ the switch button.

b. Remove the air ﬁlter cover.

c. Remove the air ﬁlter.

d. Remove the spark plug .

e. Turn the machine upside down .

f. Pull the starting rope(5-8times) to let the

fuel ﬂow out of the cylinder.

g. Put back all the parts.

Note:

Make sure the fuel doesn’t spill on you body.

4. Go back step 1 start again

1. Examine the choke position(fully close).

2. Examine the brake .(make sure brake oﬀ)

Idle Adjustment Screw

4. Idle adjustment screw (T)

Use Idle screwdriver to turn the idle adjustment

screw 1/4 to 1/2 turn anticlockwise.

5. Start the engine again .

3. Examine the saw chain.

Make sure chain still in the drive sprocket

Engin runs but the chain is not running

2. Examine the choke position(fully close).

3. Examine the saw chain.

Make sure chain still in the drive sprocket.

1. Examine the brake pad (brake oﬀ).

Make sure chain turn easily by hand.

Engine runs but clutch cover smokes

1. Examine the brake pad (brake oﬀ).

2. Examine the saw chain

Make sure chain still in the drive sprocket.

The drive sprocket will melt turbine

The brake spring will melt clutch

To lubricate the cutting equipment

To do a check of the saw chain lubrication

Do a check of the chain saw lubrication each

time you refuel.

1. Point the nose of the guide bar at a light

color surface almost 20 cm (8 in) away.

2. After 1 minute of running, a line of oil

shows on the light surface.

Cylinder ﬂooded

3. If you cannot see the line of oil after 1

minute, clean the oil channel in the guide

bar. Clean the groove in the edge of the

guide bar. Make sure the guide bar nose

sprocket turns freely and that there are no

blockages in the lubrication hole. Clean

and lubricate the tip sprocket.

To stop the engine

• Push the stop switch to stop the engine.

Note: Stop engine (0)

Open engine (1)

4. Pull the starter rope handle until the engine

starts.

5. Pull the brake oﬀ

6. Pull the throttle trigger

7. Use the product.

To start a warm engine

1. Push the chain brake on

2. Open the switch button (1open/0stop)

3. Push the choke control in fully

MAX MIN

Adjusting the automatic oiler

The oiler automatically delivers the proper

amount of oil to the guide bar and saw chain.

As the engine speed increases, so does the

oil ﬂow.

The amount of oil ﬂowing to the guide bar and

saw chain maybe changed by turning the

adjustment screw with a small standard

screwdriver.

Turn the screw clockwise to decrease oil

ﬂow or turn the screw counterclockwise

to increase oil ﬂow

Clutch

Adjustment Screw

Clutch cover

Note: mpty you oil tank when you don’t use E

If not the oil will keep coming out

switch button

Choke control

Autres manuels pour 6220G

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Salem Master Pro Tronçonneuse

Salem Master Pro

Salem Master Pro 6220G Manuel utilisateur

Manuels Tronçonneuse populaires d'autres marques

Bushranger

Bushranger CS4210 Manuel utilisateur

Husqvarna

Husqvarna 136, 141 Manuel utilisateur

Echo

Echo CS-330EVL Manuel utilisateur

HART

HART HLCS01 Manuel utilisateur

Homelite

Homelite UH10817 Manuel utilisateur

Westfalia

Westfalia SCS 725 Manuel utilisateur

Nakayama

Nakayama EC2050 Manuel utilisateur

The Handy

The Handy THPCS16 Manuel utilisateur

McCulloch

McCulloch PRO MAC 54 Manuel

Husqvarna

Husqvarna 359 E-tech Manuel utilisateur

Craftsman

Craftsman 358.352162 Manuel utilisateur

Craftsman

Craftsman 358.350270 Manuel utilisateur

Craftsman

Craftsman 358.351610 Manuel utilisateur

Echo

Echo CS-8001(6digits)(36) Mode d’emploi

Poulan Pro

Poulan Pro 545047544 Manuel utilisateur

Ryobi

Ryobi RY3714VNM Manuel utilisateur

Homelite

Homelite Ranger UT10926 Manuel utilisateur

McCulloch

McCulloch TimberBear TM502 Manuel utilisateur