Ruckus Wireless ZoneFlex 7982 Manuel utilisateur

Published June 2012, Part Number 800-70362-001 Rev C

ZoneFlex 7982 Dual Band

802.11n Multimedia Wi-Fi

Access Point

Quick Setup Guide

This Quick Setup Guide provides step-by-step instructions

on how to set up your Ruckus Wireless ZoneFlex Access

Point. After completing the steps described in this Guide,

you will be able to place the Access Point (AP) at your site

and provide wireless network access to users.

BEFORE YOU BEGIN

Before deploying Ruckus Wireless products, please check for

the latest software and the release documentation.

• User Guides and Release Notes are available at

http://support.ruckuswireless.com/documents.

• Software Upgrades are available at

http://support.ruckuswireless.com/software.

• Open Source information is available at

http://opensource.ruckuswireless.com.

• Software License and Limited Warranty available at

http://support.ruckuswireless.com/warranty.

PACKAGE CONTENTS

• ZoneFlex 7982 Access Point

• Mounting screws and anchors (2)

• T-Bar clips and alignment spacer

• Security screw

• Regulatory flyer

•ThisQuick Setup Guide

SETUP REQUIREMENTS

• A computer running Windows 7(procedures for other OS’s

are similar)

• One or more of the following:

• A modem (DSL or cable), broadband router, or other

device provided by your Internet Service Provider

that brings Internet access to your site.

• A network switch or a DSL/Internet gateway device.

• Two Cat 5e Ethernet cables

• An AC power adapter (sold separately), or

• An 802.3af or 802.3at -compliant Power over Ethernet (PoE)

switch or PoE injector

STEP 1: CONNECT THE AP TO YOUR COMPUTER

1After removing your Ruckus Wireless AP from its pack-

age, place it next to your computer.

2Using an Ethernet cable, connect your computer’s net-

work port to one of the two ports on the AP.

3Using an AC adapter (sold separately), connect the AP to

a convenient (and protected) power source.

• Alternatively, connect the 10/100/1000 POE port to a

PoE injector or switch for both power and network

connectivity.

4Verify that the Power LED on the external enclosure is a

steady green.

STEP 2: PREPARE YOUR COMPUTER FOR AP

SETUP

1On your Windows 7 computer, configure your network

adapter from the Local Area Connection settings as fol-

lows:

• Start > Control Panel > Network and Sharing Cen-

ter > Change Adapter Settings

2Edit the TCP/IPv4 address settings as follows:

• Local Area Connection > Properties > Internet

Protocol Version 4 (TCP/IPv4) > Properties

The TCP/IPv4 Properties dialog box appears.

3Select Use the following IP address (if it is not already

selected) and then make the following entries:

•IP address: 192.168.0.22 (or any address in the

192.168.0.x network)

•Subnet mask: 255.255.255.0

•Default gateway: 192.168.0.1

Leave the DNS server fields empty.

4Click OK to save your changes.

Your changes are put into effect immediately.

STEP 3: LOG INTO THE AP

As specified earlier, the AP should be directly connected to

your computer (through one of the Ethernet ports) and

powered on, ready for setup.

1On your computer, open a Web browser window.

2In the browser, type this URL to connect to the AP:

https://192.168.0.1

3Press <Enter> to initiate the connection. When a security

alert dialog box appears, click OK/Yes to proceed.

4When the Ruckus Wireless Admin login page appears,

enter the following:

•Username: super

•Password: sp-admin

5Click Login.

IMPORTANT!

If the AP is deployed with a ZoneDirector, follow the

ZoneDirector Quick Setup Guide, and connect the AP to

your local network.

PoE In DC input

NOTE:

The following procedures assume Windows 7 as the oper-

ating system. Procedures for other OS’s are similar.

IMPORTANT!

Write down all of the currently active settings so you can

restore your computer to its current configuration later

(when this process is complete).

Published June 2012, Part Number 800-70362-001 Rev C

STEP 4: CUSTOMIZE THE WIRELESS SETTINGS

1On the Web interface menu, click Configuration >

Radio 2.4G or Configuration > Radio 5G. The Config-

ure :: Wireless :: Common options appear.

2Verify that the following options are active:

•Channel: SmartSelect

•Country Code: If you are not located in the United

States, select your current country.

3Click Update Settings if you made any changes.

4Click any of the “Wireless #” tabs at the top

of the page.

5In Wireless Availability, click Enabled.

6Delete the text in the SSID field, then type a name for

your network that will help your users identify the AP in

their wireless network connection application.

7Click Update Settings to save your changes.

8Repeat Steps 4-7 for each Wireless # interface that you

want to enable.

9Click Logout to exit the Web interface.

10 When the Ruckus Wireless Admin login page reappears,

you can exit your browser.

11 Disconnect the AP from the computer and from the

current power source, and then restore your computer to

its original network connection configuration.

STEP 5: PLACE THE AP IN YOUR SITE

1Disconnect the AP’s power adapter from the power out-

let.

2Move the AP to its permanent location (accessible to

both power and network connections). See enclosed

Mounting Instructions for physical installation.

3Use an Ethernet cable to connect the 10/100/1000 port

to your network.

4Connect the AP power adapter (or PoE power supply) to

the AP, then to a convenient power source.

5Verify that the 10/100/1000 port LED is lit.

After a short pause to re-establish the Internet connection,

you can test the AP.

STEP 6: VERIFY THE INSTALLATION

1Using any wireless-enabled computer or mobile device,

search for and select the wireless network you previously

configured.

2If you can connect, open a browser and link to any public

Web site.

Congratulations! Your wireless network is active and ready

for use.

For More Information

You can now use the wireless network to log into the AP’s

Web interface. For information on how to configure the AP

from the Web interface, refer to the Ruckus Wireless

ZoneFlex Access Point User Guide or the Online Help,

available from within the Web interface.

Default AP Settings (For Your Reference)

Network Names (SSIDs) Wireless1—Wireless8

(2.4GHz radio)

Wireless9—Wireless16

(5GHz radio)

Security (Encryption

method)

Disabled for each wireless

interface

Default Management IP

Address

192.168.0.1

OPTIONAL: IF YOU WANT TO SWITCH FROM DHCP

(DEFAULT)

If you anticipate logging into the AP regularly to perform

monitoring or maintenance (once it is in place), you may want

to consider assigning a static IP address to the AP.

In a default AP configuration, the AP uses a DHCP-

assigned IP address.

A. On the menu, click Configuration > Internet.

B. Click the Static IP option.

C. Fill in the IP Address and Mask fields.

D. Click Update Settings to save your changes.

NOTE: If you will be using PoE, you will need a Cat 5e (or

better) Ethernet cable to connect the AP to the PoE injec-

tor or switch.

Published June 2012, Part Number 800-70362-001 Rev C

(OPTIONAL) MOUNTING INSTRUCTIONS

The ZoneFlex 7982 can be mounted to a wall, ceiling or to a

T-bar using the enclosed mounting kit, or the T-bar clips built

into the bottom of the AP enclosure.

Mounting to a T-Bar: Recessed Tile Drop Ceiling

1Fasten T-Bar clips (included) to the T-Bar.

2Fit the screws protruding from the T-Bar clips through the

holes in the alignment spacer, and then thread the

included anchor sleeves onto the screws. Adjust the

height of the anchor sleeves such that the anchor heads

extend just below the ceiling tile surface.

3Insert a straightened paperclip (or similar) into the pin-

hole on the side of the AP and hold in place while

mounting (see Figure 1.).

4Place the AP over the anchor sleeves such that the heads

enter the mounting holes on the AP enclosure, and slide

the AP to lock in place.

5Remove the paperclip to release the lock mechanism

and secure the AP.

6To remove the AP, insert a straightened paperclip into

the hole on the side of the AP to unlock, and then slide

the AP to release the AP enclosure from the mounting

screws.

Figure 1. Recessed tile T-bar mounting

Mounting to a T-Bar: Flush Tile Drop Ceiling

1Orient the AP so that the T-bar is positioned between the

T-bar clips as shown in Figure 2., then rotate the AP until

the third T-bar clip catches the T-bar and the latch locks

the T-bar in place (Figure 3.).

Figure 2. Place the AP onto the T-bar

Figure 3. Rotate the AP so that it locks in place

2To remove the unit from the T-Bar, insert a straightened

paperclip into the hole on the side of the AP to unlock,

then rotate the AP to release the enclosure from the T-

Bar.

Mounting to a Flat Surface

1Use the Mounting Template on the reverse side of this

Quick Setup Guide as a template to mark the locations

for drill holes on the mounting surface. There are two

sets of keyholes available on the AP. One allows the AP

to be mounted to a wall or ceiling. The other allows the

ZoneFlex 7982 to be mounted to an accessory bracket

(not included).

2Use a 5mm drill bit to drill holes approximately 25mm

into the mounting surface.

3Insert the anchors and mounting screws into the mount-

ing surface, leaving approximately 1/4” (6 mm) of the

screw heads protruding for the AP enclosure.

4Insert a straightened paperclip (or similar) into the hole

on the side of the AP to release the locking mechanism.

5Place the AP onto the mounting screws so that the screw

heads enter the mounting holes on the AP enclosure,

and push the AP down to lock in place.

6Remove the paperclip to release the locking mechanism

and secure the AP.

7To remove the AP, insert a straightened paperclip into

the hole on the side of the AP to unlock, then push the

AP up to release the AP enclosure from the mounting

screws.

Figure 4. Wall mounting

Note: if the T-bar clips slide easily along the T-bar, use a

piece of Scotch tape or similar to secure them in place

while mounting the AP. The tape may be removed once

the AP is mounted.

Hold paperclip in

while mounting

WALL / CEILING MOUNT TEMPLATE

NTIN

DRILL HER

EILIN

BRA

Autres manuels pour ZoneFlex 7982

Table des matières

Autres manuels Ruckus Wireless Point d'accès sans fil

Ruckus Wireless

Ruckus Wireless T750 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless C500 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless R560 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex 2741 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex 7441 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex 7782-E Manuel d'instructions d'installation

Ruckus Wireless

Ruckus Wireless zoneflex t301n Manuel d'instructions d'installation

Ruckus Wireless

Ruckus Wireless ZoneFlex series Manuel utilisateur

Ruckus Wireless

Ruckus Wireless Unleashed R600 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex 7321-U Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex 7025 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless E510 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless C110 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless zoneflex t301n Manuel utilisateur

Ruckus Wireless

Ruckus Wireless R750 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex R710 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless T310c Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex 7343 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex R500 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex 7962 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex 7341 802.11n Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex 7761-CM Manuel utilisateur

Ruckus Wireless

Ruckus Wireless ZoneFlex 7982 Manuel utilisateur

Ruckus Wireless

Ruckus Wireless R610 Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur