RS PRO RS 155B Manuel utilisateur



Instruction Manual

RS 155B (162-4455) / RS 156B (162-4456)

RS 157B (162-4457) / RS 158B (162-4458)

Clamp Meter

RS 158B

Press 2 sec

150B Series / EN

Warning

. . . . . . . . . .

. . . . . . . .

Safety sheet

. . . . . . . . .

. . . . . . . . . .

. . . . . . . .

. . . . . . . . .



Read First

Safety Information

Understand and follow operating instructions carefully.

Use the meter only as specified in this manual; otherwise, the

protection provided by the meter may be impaired.

 WARNING

Identifies hazardous conditions and actions that could cause

BODILY HARM or DEATH

CAUTION

Identifies conditions and actions that could DAMAGE the meter

or equipment under test

 WARNING

˙When using test leads or probes, keep your fingers behind

the finger guards.

˙ Individual protective equipment should be used if HAZARD-

OUS LIVE parts in the installation where measurement is to

be carried out could be ACCESSIBLE.

˙Remove test lead from meter before opening the battery

door or meter case.

˙Use the meter only as specified in this manual or the protec-

tion by the meter might be impaired.

˙ Always use proper terminals, switch position, and range for

measurements.

˙ Verify the meter’s operation by measuring a known voltage.

If in doubt, have the meter serviced.

˙Do not apply more than the rated voltage, as marked on

meter, between terminals or between any terminal and

earth ground.

˙Use caution with voltages above 30 V ac rms, 42 V ac peak,

or 60 V dc. These voltages pose a shock hazard.

˙To avoid false readings that can lead to electric shock and

injury, replace battery as soon as low battery indicator blinks.

˙Disconnect circuit power and discharge all high-voltage

capacitors before testing resistance, continuity, diodes, or

capacitance.

˙Do not use meter around explosive gas or vapor.

˙ To reduce the risk of fire or electric shock do not expose

this product to rain or moisture.

˙ Probe assemblies to be used for MAINS measurements

shall be RATED as appropriate for MEASUREMENT

CATEGORY III or IV according to EN 61010-031 and shall

have a voltage RATING of at least the voltage of the circuit

to be measured.

Warning Safety sheet

150B Series / EN

CAUTION

˙Disconnect the test leads from the test points before chang-

ing the position of the function rotary switch.

˙Never connect a source of voltage with the function rotary

switch in Ω, %,and position.

˙Do not expose meter to extremes in temperature or high

humidity.

˙ Never set the meter in Ω, %,and function to measure

the voltage of a power supply circuit in equipment that could

result in damage the meter and the equipment under test.

Symbols as marked on the Meter and Instruction

manual

Unsafe Voltage

To alert you to the presence of a potentially hazardous voltage,

when the Tester detects a voltage ≧30 V or a voltage overload

(OL) in V .The symbol is displayed.

Maintenance

Do not attempt to repair this meter. It contains no user

serviceable parts. Repair or servicing should only be performed

by qualified personnel.

Cleaning

Periodically wipe the case with a dry cloth and detergent.

Do not use abrasives or solvents.

Risk of electric shock

See instruction manual

DC measurement

Equipment protected by double or reinforced

insulation

Battery

Earth

AC measurement

Conforms to EU directives

EApplication around and removal from hazardous live

conductors is permitted

Do not discard this product or throw away.

150B Series / EN

Feature

˙10000 Count digital display

˙Active Backlit,Large scale display

˙VoltSeek (None Contact Voltage)

˙Analog Bar graph

˙True RMS reading on AC and AC+DC mode

˙Memory Save/Load (data amount up to 1000 )

˙Data logger (data amount up to 9999 )

˙Bluetooth wireless communication

˙Torch lightening when clamping

˙Auto AC/DC 1000 Amps capability and selection (For 158B)

˙Auto AC/DC 600 Amps capability and selection (For 156B)

˙Auto AC/DC 1000 Volts capability and selection

˙Auto Ohms/Continuity/Diode selection

˙100K Resistance capability

˙Continuity Beeper

˙Frequency Counter

˙Power and Power factor measurement

˙Total Harmonics distortion and Harmonics 1 to 25

˙Capacitance capability

˙°C / °F Temperature Function (For 158B)

˙Inrush Current

˙DCA Auto-Zeroing Button (For 156B/158B)

˙Peak Hold

˙MIN/MAX HOLD

˙Smart Data Hold

˙Phase rotation indication

˙Flex AC Current

˙High frequency rejection

˙Auto Powet Off

˙CAT.Ⅳ600V / CAT.Ⅲ1000V Safety Standard

150B Series / EN

Unpacking and Inspection

Upon removing your new Power Clamp Meter from its packing,

you should have the following items:

1. Power Clamp Meter

2. Test leads. set (1 x Black, 1 x Red)

3. Temperature Probe (For 158B)

4. User Manual

5. Carrying case

6. Battery

The Meter Description

Press 2 sec

150B Series / EN

Power On / Off

Power on

Auto Power Off

After idle 15 min

The meter can work again by turning it on from the OFF

position.

After turning on the meter,

the LCD will show Full,

half, and low to indicate

the battery capacity.

150B Series / EN

Auto Power Off (APO) disable :

Press OK button while tuning meter on from OFF position.

Push Buttons

Bluetooth

UP/DOWN

LEFT RIGHT

Menu Operation

Example

Use arrow keys to move the blinking cursor to the

target icon, and then press OK button

Use arrow keys to move the blinking cursor to the

target icon, and then press OK button for more

than 2 seconds.

The icon without underline means the function is

not executed.

The icon with underline means the function is

executed.

150B Series / EN

Making Basic Measurements

Preparation and Caution Before Measurement

: Observe the rules of Warnings and Cautions

The figures on the following pages show how to make

basic measurements.

When connecting the test leads to the DUT (Device Under Test),

connect the common test lead before connecting the live lead.

When removing the test leads, remove the test live lead before

removing the common test lead.

Measuring Voltage

150B Series / EN

Warning

To avoid electrical shock, hazard or damage to meter, do not

attempt to measurement that might exceed 1000 V dc or ac

RMS. Do not apply more then 1000 V dc or ac RMS between

the common input terminal and earth ground.

Note - If the measured voltage is greater than 30 V dc or ac

RMS, the display will show the " " symbol.

Measuring Current

- DO NOT clamp on any conductor while the meter power on.

- 155B/157B has only AC current measurement mode.

- Torch lightening when clamping.

I+(-I)=0

CAT.Ⅳ.600V

CAT.Ⅲ.1000V

with respect to

earth for the jaw.

Tactile Barrier for

hand guard.

Do not hold

the meter across

the Tactile Barrier.

150B Series / EN

AUTO SENSE mode :

Display measurement result at AC only with RMS value or

DC value, it depends on whichever is greater.

AC mode : AC only with RMS value.

DC mode : DC value.

AC+DC mode : AC+DC RMS value.

Note

- Press MODE button to enter the AC/DC/AC+DC mode.

- Press MODE button for more than 2 seconds to return to the

AUTO SENSE mode.

PEAK HOLD (AC mode only)

ACV mode

>2SEC

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels RS PRO Instrument de mesure

RS PRO

RS PRO 1389 Manuel utilisateur

RS PRO

RS PRO ISM 400 Manuel utilisateur

RS PRO

RS PRO SLM 1353M Manuel utilisateur

RS PRO

RS PRO IM-194 Manuel utilisateur

RS PRO

RS PRO RS-137 Manuel utilisateur

RS PRO

RS PRO RS-172 Manuel utilisateur

RS PRO

RS PRO RS-8890D Manuel utilisateur

RS PRO

RS PRO RS-96 Manuel utilisateur

RS PRO

RS PRO ILOM-508A Manuel utilisateur

RS PRO

RS PRO RS-8890G Manuel utilisateur

RS PRO

RS PRO IM-502 Manuel utilisateur

RS PRO

RS PRO RM-804 Manuel utilisateur

RS PRO

RS PRO IM-195 Manuel utilisateur

RS PRO

RS PRO RS-8880 Manuel utilisateur

RS PRO

RS PRO IM-740 Manuel utilisateur

RS PRO

RS PRO 877-1791 Manuel utilisateur

RS PRO

RS PRO RS-1013 Manuel utilisateur

RS PRO

RS PRO RS-1150 Manuel utilisateur

RS PRO

RS PRO ICM 20 Manuel utilisateur

RS PRO

RS PRO RS-3893 Manuel utilisateur

RS PRO

RS PRO ISM 410 Manuel utilisateur

RS PRO

RS PRO RS-1340 Manuel utilisateur

RS PRO

RS PRO RS-3809 Manuel utilisateur

RS PRO

RS PRO RS-95 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur