RS PRO IPM 3600N Manuel utilisateur

INSTRUCTION MANUAL

IPM 3600N

3 Phase Power Analyser

3 4

1 2

MAG.

U12 Y-M

-h

NO.

U23 D-h U31 m-s

3 Phase Power Analyser / EN

09/30/16 Version No. 00

CONTENTS

Title Page

I. SAFETY INFORMATION..........................................................................1

II. INTRODUCTION.......................................................................................3

III. SPECIFICATIONS ....................................................................................4

3-1 Environmental Conditions .........................................................................4

3-2 Safety Specifications .................................................................................4

3-3 General Specifications...............................................................................5

3-4 Electrical Specification...............................................................................5

IV. PARTS & CONTROLS .............................................................................9

4-1 Description of Parts & Control keys...........................................................9

4-2 Description of Display..............................................................................13

V. OPERATING INSTRUCTIONS...............................................................16

5-1 ICA 3600N AC Current Probe Connection ..............................................16

5-2 Single-Phase 2-Wire (1P2W) Power System Measurement...................18

5-3 Single-Phase 3-Wire (1P3W) Power System Measurement...................20

5-4 Three-Phase 3-Wire (3P3W2M) Power System Measurement ..............22

5-5 Three-Phase 3-Wire (3P3W3M) Power System Measurement ..............25

5-6 Three-Phase 4-Wire (3P4W) Power System Measurement...................27

5-7 Single Phase Current Measurement.......................................................29

5-8 Manual Data Memory and Read Function Operation..............................30

5-9 Auto Data logging Function Operation ....................................................30

5-10 Phase Sequence Measurement............................................................31

5-11 Voltage, Current Waveform and Harmonic Analyzer.............................33

5-12 Enable Auto Power Off Function...........................................................33

VI. MAINTENANCE......................................................................................34

6-1 General Maintenance..............................................................................34

6-2 Battery Replacement...............................................................................34

VII. SOFTWARE INSTALLATION AND OPERATION..................................35

3 Phase Power Analyser / EN

1 09/30/16 Version No. 00

I. SAFETY INFORMATION

The following symbols may appear on the instrument and in this instruction manual:

Caution refer to this manual before using the instrument.

This mark indicates explanation, which is particularly important that the user should

read before using the instrument.

Risk of electric shock

Instrument is protected bydouble insulation or reinforced insulation.

Conforms to relevant EU directives

Dispose of in accordance with local regulations.

Safety Information

Read and understand this instruction manual completely before using this instrument. Failure to

observe the warnings and cautions in this instruction manual may result in injury, death or damage

to the instrument and other equipment or property.

If this instrument is used in a manner not specified in these instructions, the protection provided by

the instrument may be impaired

DANGER

•Do not store or use the instrument where it will be exposed to direct sunlight, high temperature,

high humidity, or condensation

•The instrument is designed for indoor use and can be safely used at temperatures ranging from

0°C to 40°C

•To prevent electric shock, do not allow the instrument to come into contact with water, do not

use in damp conditions and do not use the unit with wet hands

•Do not use the instrument in hazardous areas or around explosive or corrosive gases or vapours

•Examine the instrument and probes before use, do not use them if they are damaged

•Do not apply more than the rated voltage, as marked on the instrument and probes, between

terminals or between any terminal and earth ground

•To prevent electric shock, de-energise power systems before making connections whenever

possible

•Whenever possible, make connections to the output side of a circuit breaker to provide

better short circuit protection.

•Use caution with voltages above 30 Vac rms, 42 Vac peak, or 60 Vdc. These voltages pose a

shock hazard

•Use extreme caution when working around bare conductors or bus bars. Accidental contact with

the conductor could result in electric shock.

•Wear suitable personal protective equipment when working around or near hazardous live

conductors which could be accessible

3 Phase Power Analyser / EN

09/30/16 Version No. 00 2

WARNING

•Do not hold the test leads or probes beyond the finger guards or tactile barriers

•Remove all probes, test leads and accessories that are not required for the test

•Always use proper terminals, switch position, and range for measurements

•Verify the instrument is operating correctly by measuring a known voltage before use. If in doubt,

have the instrument serviced

•To avoid false readings that can lead to electric shock and injury, replace battery as soon as the

low battery indicator “

”

appears

•Follow all legal requirements

•Obey posted instructions

•Never assume that a circuit is de-energized, check it first

•Always set up the measurement first, then connect the test leads and probes to the

instrument before connecting to the circuit under test

•Connect the ground lead first, then the voltage leads and the current probe, Disconnect in

the reverse order

•Route all test leads carefully

•Remove test leads from instrument before opening the battery door or instrument case

CAUTION:

The measurement inputs U1, U2 and U3 are not isolated from each other, input

N is the common reference point. Connecting either U1, U2 or U3 to the circuit

means that the others are also live and therefore a danger of electric shock is

present. To avoid electrical shock, connect only the probes and test leads

required for the test.

3 Phase Power Analyser / EN

3 09/30/16 Version No. 00

II. INTRODUCTION

The IPM 3600N is a 3 phase power analyser for portable measurement within public mains

supplies.

The analyzer can be used to analyse and trouble shoot power quality issues, improve power

efficiency, manage energy costs, analyze harmonics, optimize power system performance,

improve power quality and analyze system data to design optimal upgrades.

Features

•10 display LCD screen, capable of showing many power quality parameters at the same time.

•4 current probes included for measuring 3 phase and neutral line current.

•Measures single-phase 2-wire, single-phase 3-wire, three-phase 3-wire and three-phase 4-wire

systems.

•All true-RMS sensing, V,A, KW, KVAR, KVA, PF, θ, Hz, KWh, KVARh and KVAh measurements.

•Phase sequence indicator function.

•Backlight display function.

•Manual Data Memory and Read (50 sets).

•Data logging (micro SD CARD 4GB).

•USB optical PC interface with three phase voltage / current waveform display and harmonic

analysis.

Supplied accessories

•ICA 3600N AC current probe x 4

Category Rating: CAT III 600V per IEC61010-1, Pollution Degree2.

: IEC 61010-1 2nd Edition and IEC61010-2-032

Input : AC 1000A maximum.

Output : 0.35mV/A

•Voltage test lead x 4

Model no : TL 202I

Manufacturer : Hong Kai Co., Ltd.

Category Rating : CAT III, 1000V AC 10A Max.

•Alligator clip x 4

Model no : FC-A26

Manufacturer : Fu Chyi Enterprise CO., Ltd.

Category Rating : CAT III, 1000V AC 10A Max.

•AC Adaptor (IN-OUT Isolated type, Input 230V AC 50Hz)

Model : MWD48-1200300GS

Input : 230V AC 50Hz

Output : 12V DC 300mA

Manufacturer : MAW WOEI Enterprise CO., Ltd.

•Battery 1.5V “AA” x 8

•Instruction manual x 1

•PC software CD-R x 1

•Carrying case x 1

•Optical USB interface x 1

3 Phase Power Analyser / EN

09/30/16 Version No. 00 4

III. SPECIFICATIONS

3-1 Environmental Conditions

•Altitude up to 2000 metres

•Indoor use only

•Ambient operating temperature: 0 to 40°C

•Operating humidity : Max 80%RH ≤31°C decrease linearly to 50% relative humidity at 40°C

(non-condensing).

•Storage temperature and humidity : -10 to 60°C R.H. < 70% non-condensing.

3-2 Safety Specifications

IPM 3600N Power Analyser

Category Rating : CAT III 1000V per IEC 61010-1

Pollution Degree 2

: IEC 61010-1 2nd Edition

ICA 3600N AC current probes:

Current Clamps, model ICA3600N, to be used only with the Three-Phase power analyzer,

model IPM 3600N.

Category Rating: CAT III 600V per IEC61010-1,

Pollution Degree2.

: IEC 61010-1 2nd Edition and IEC61010-2-032

Input : AC 1000A maximum.

Output : 0.35mV/A

Voltage test leads:

Category Rating : CAT III, 1000V, AC 10A Max.

Alligator clip:

Category Rating : CAT III, 1000V, AC 10A Max.

Category definitions

Measurement

Category Application

I Measurements on circuits not directly connected to mains.

Examples include: Measurements on battery powered equipment and

specially protected (internal) mains-derived circuits.

II Measurements on circuits directly connected to the low voltage installation.

Examples include: Household appliances, portable tools and similar equipment.

III Measurements performed in the building installation.

Examples include measurements on distribution boards, junction boxes,

socket-outlets and wiring and cables in the fixed installation.

IV Measurements performed at the source of the low-voltage installation.

Examples include measurements on primary over current protection devices

and electricity meters

3 Phase Power Analyser / EN

5 09/30/16 Version No. 00

3-3 General Specifications

•Maximum voltage between voltage input terminals and earth ground : 1000 Vrms

•Maximum rated working voltage for current input : 0.35 Vrms

•Maximum current for current probe : 1000Arms

•Numerical display : 10 display 4 digit LCD maximum reading 9999.

•Battery life : approx. 50 hours.

•Auto power off : approx. 30 minutes.

•Low battery indication : The “

” symbol is displayed when the battery voltage drops below

the operating voltage.

•Backlight display time : Auto off approx. 30 seconds.

•Sampling rate : Approx. 1 time per 2 seconds (Digital display).

•Harmonic analyzer : 1 ~ 63th order.

•Manual data memory and read capacity: 50 sets.

•Data logger capacity: micro SD CARD 4GB (Maximum 99 blocks).

•Current probe jaw opening diameter : Cables φ40mm.

•Storage temperature and humidity : -10 to 60°C R.H. < 70% non-condensing.

•Dimensions :

Instrument: 235x117x54 mm.

Current probe: 193x88x40 mm.

•Weight :

Instrument including battery: ~ 730g

Current probe: ~ 333g

3-4 Electrical Specification

Accuracy : ±(% of reading + number of digits) at 23°C ± 5°C ≤80%RH

Temperature coefficient : 0.1 ± (specified accuracy)

/ °C (<18 or >28°C)

1. Position the conductor within the jaws at the intersection

of the indicated marks as much as possible in order to

meet this meter’s accuracy.

2. If the conductor is positioned elsewhere within the jaws,

the maximum additional error is 1.5 percent.

Figure 1. Current Probe Positional Error



AC Voltage Trms measurement (Vrms) :

Range Resolution

Accuracy Input

impedance

Overload

protection

Nominal power

system frequency

10 to 999.9V

0.1V ±(0.3%rdg±10dgts)

2MΩ1000Vrms

50Hz

•Display item : RMS voltage value for each channel.

3 Phase Power Analyser / EN

09/30/16 Version No. 00 6

AC Current Trms Measurement (Arms) :

Range Resolution

Accuracy

(including current probe)

Current probe

output Overload

protection

Nominal power

system frequency

10 to 299.9A

±0.5%rdg±15dgts

300 to 999.9A

0.1A ±1.2%rdg±15dgts 0.35mV/A

1000Arms

50Hz

•Display item : RMS current value for each channel.

Active Power measurement P (KW) :

Range Resolution Accuracy

0.1 to 999.9KW 0.1KW ±1.0%rdg±20dgts (10 to 299.9A)

±1.5%rdg±20dgts (300 to 999.9A)

•Display items : Active power of each channel and its sum of multiple channels.

•Polarity display : For influx (consumption) No symbol, For outflow (regenerative) “ - ”.

Apparent Power measurement S (KVA) :

Range Resolution Accuracy

0.1 to 999.9KVA 0.1KVA ±1.0%rdg±20dgts (10 to 299.9A)

±1.5%rdg±20dgts (300 to 999.9A)

•Measurement method : Calculated from RMS voltage U and RMS current I.

•Display item : Apparent power of each channel and its sum of multiple channels.

•Polarity display : No polarity.

Reactive Power measurement Q (KVAR) :

Range Resolution Accuracy

0.1 to 999.9KVAR 0.1KVAR ±1.0%rdg±20dgts (10 to 299.9A)

±1.5%rdg±20dgts (300 to 999.9A)

•Measurement method : Calculated from apparent power S and active power P,

Q =

2 2

−

•Display item : Reactive power of each channel and its sum of multiple channels.

•Polarity display : For phase lag : No symbol.

For lead phase : “-”



Power Factor measurement (COSφ) :

Range Resolution CalculatedAccuracy

-1

+1 0.001 ±10dgt

•Measurement method : Calculated from apparent power S and active power P,

PF = COSφ=

P S/

•Display item : Power factor of each channel and its sum of multiple channels.

3 Phase Power Analyser / EN

7 09/30/16 Version No. 00



Phase angle measurement (φ) :

Range Resolution CalculatedAccuracy

0.1°

to +180°, 0.1°

to -180°0.1°±15dgt

•Measurement method : Calculated from power factor COSφ,φ= COS

-1

PF.

•Display item : Phase angle of each channel and its sum of multiple channels.

•Polarity display :

For phase lag : No symbol

For phase lead : “-”.

Frequency measurement (Hz) :

Range Resolution Accuracy Measurement source

50Hz 0.1Hz ±0.1%rdg±2dgt Voltage U1 > 50V

•Measurable input range : > 50V

Three Phase Sequence Detection :

Input voltage range

Normal phase indication

Reverse phase indication

Measurement source

3P > 50V to 1000V

U1, U2 and U3

Active Power Energy measurement (kWh) :

Range Resolution Active power accuracy

Timer interval

TimerAccuracy

0.001 to 9.999KWh

0.001KWh

0.01 to 99.99KWh

0.01KWh

0.1 to 999.9KWh

0.1KWh

0.001 to 9.999MWh

0.001MWh

0.01 to 30.59MWh

0.01MWh

±1.0%rdg±20dgts

(10 to 299.9A)

±1.5%rdg±20dgts

(300 to 999.9A)

1 sec ±50ppm (25°C)

•Measurement display : Display all active power consumption energy (sum of absolute values).

Apparent Power Energy measurement (kVAh) :

Range Resolution

Apparent power

accuracy Timer interval

TimerAccuracy

0.001 to 9.999kVAh

0.001kVAh

0.01 to 99.99kVAh

0.01kVAh

0.1 to 999.9kVAh

0.1kVAh

0.001 to 9.999MVAh

0.001MVAh

0.01 to 30.59MVAh

0.01MVAh

±1.0%rdg±20dgts

(10 to 299.9A)

±1.5%rdg±20dgts

(300 to 999.9A)

1 sec ±50ppm (25°C, 77°F)

•Measurement display : Display all apparent power energy (sum of absolute values).

Table des matières

Autres manuels RS PRO Instrument de mesure

RS PRO

RS PRO 2377271 Manuel utilisateur

RS PRO

RS PRO RS-1013 Manuel utilisateur

RS PRO

RS PRO RS-1260 Manuel utilisateur

RS PRO

RS PRO RS-92 Manuel utilisateur

RS PRO

RS PRO RS-3381 Manuel utilisateur

RS PRO

RS PRO ILOM-508A Manuel utilisateur

RS PRO

RS PRO RS-8890D Manuel utilisateur

RS PRO

RS PRO ICM A6N Manuel utilisateur

RS PRO

RS PRO 877-1791 Manuel utilisateur

RS PRO

RS PRO RS-5322 Manuel utilisateur

RS PRO

RS PRO RS-90 Manuel utilisateur

RS PRO

RS PRO LCR-6000 Series Manuel utilisateur

RS PRO

RS PRO RS-96 Manuel utilisateur

RS PRO

RS PRO ICM 134 Manuel utilisateur

RS PRO

RS PRO 623-883 Manuel

RS PRO

RS PRO IM-502 Manuel utilisateur

RS PRO

RS PRO RS-9985 Manuel utilisateur

RS PRO

RS PRO RS-1360A Manuel utilisateur

RS PRO

RS PRO RS-9968BT Manuel utilisateur

RS PRO

RS PRO IM-740 Manuel utilisateur

RS PRO

RS PRO RSST-2000 Series Manuel utilisateur

RS PRO

RS PRO RS-1361C Manuel utilisateur

RS PRO

RS PRO RS-8890 Manuel utilisateur

RS PRO

RS PRO RS-326 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur