RP LIGHTING 1073LED-PC Manuel utilisateur
1073-PC
For Models:
Installation Guide
1073LED-PC
SAFETY INFORMATION
CANOPY ASSEMBLY
BLADES INSTALLATION
ATTACHING SWITCH HOUSING MOUNTING PLATE
TOOLS REQUIRED 2
1
2.3
UNPACKING FAN
INSTALLING MOUNTING BRACKET 4
DOWNROD / BALL ASSEMBLY 5
HANGING THE FAN MOTOR ASSEMBLY 5
MAKING ELECTRICAL CONNECTIONS 6
9
8
7
8
8
10
11.12
9
13
13
TROUBLESHOOTING
CARE OF YOUR FAN
OPTIONAL LIGHT KIT INSTALLATION
OPERATING YOUR FAN
ATTACHING SWITCH HOUSING
LIGHT KIT INSTALLATION
ELECTRICAL CONNECTIONS (FOR OPTIONAL WALL CONTROL)
1
SAFETY INFORMATION
1. To reduce the risk of electric shock, turn the electricity off at main fuse box or circuit breaker
before beginning fan installation or servicing the fan.
2. Read all instructions and safety information carefully before installing your fan and save this
manual.
3. All electric connections must be complied with local electrical code and the National Electrical
Code. If you are unfamiliar with electrical wiring, please have a qualified licensed electrician
perform the installation.
4. The fan must be mounted with a minimum of 7 Ft (2.1M) clearance from the trailing edge of the
bales to the floor.
5. The metal outlet box and ceiling support joist must be securely mounted, and capable of reliably
supporting a minimum of 50 lbs ( 23 kgs).
Use only UL - listed outlet boxes marked “Acceptable For Fan Support.”
6. To reduce the risk of personal injury, use only approved hanging brackets and screws supplied
with the fan for mounting to the outlet box.
7. After completing installation, check all setscrews and make sure they are firmly secured.
WARNING: To reducethe risk of fire or electric shock, do NOT usethis fan with any solid-state speed control
device.
WARNING: To reduce the risk of personal injury, do NOT insert foreign objects in between rotating fan
blades.
CAUTION: To reduce the risk of personal injury, use only set screws provided with the fan for mounting to
the outlet box.
Most outlet boxes commonly used for supporting of the lighting fixture are not acceptable for fan
support and may need to be replaced. Consult a qualified electrician if in doubt.
8. Wooden blades are not intended for storage or installation in spaces that are not
temperature controlled. To avoid issues with blade warping do not store or install ceiling
fans in areas without air conditioning.
9. Do not operate reversing switch while fan blades are in motion. Fan must be turned off
and blades stopped before reversing blade direction.
WARNING: To reduce the risk of personal injury, use only parts provided with fan.
The use of parts other than those provided with fan will void the warranty.
2
#
Parts
Quantity
1
Mounting bracket
1
2 Downrod & ball assembly
1
3
Ceiling canopy
1
4
Coupling cover 1
5
Fan motor assembly 1
6
Switch housing mounting plate
Switch housing
1
7
3
8
Fan blades
1
9. Hardware bag included:
#
Quantity
a.
Wood screws
2
b.
Mounting bracket screws
2
c.
Wire nuts
2
d.
Blade holder screws
2
e.
Flat washers
7
f.
Spring washers
3
g.
Blade kit
3
h.
Pull chain (wood tassel) 1
i.
Balance kit
1set
Model:1073-PC
TOOLS REQUIRED
．Ladder
·Wire Strippers
·Phillips Screwdriver
·Pliers
UNPACKING FAN
Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing
and place on clean floor or Styrofoam to avoid damage to finish.
Do not discard fan carton or Styrofoam inserts should this fan will need to be returned for repairs.
Check against parts list that all parts have been included.
1
5
6
7
8
9
2
3
4
f.
a.
b.
c.
d.
e. g. h.
i.
3
#
Parts
Quantity
1
Mounting bracket
1
2 Downrod & ball assembly
1
3
Ceiling canopy
1
4
Coupling cover
1
5
Fan motor assembly
1
6
Mounting plate
1
7
LED Light kit 3
8
Fan blades
1
Model:1073LED-PC
1 4
5
6
7
8
9
2
3
f.
a.
b.
c.
d.
e. g. h.
i.
9. Hardware bag included:
#
Quantity
a.
Wood screws
2
b.
Mounting bracket screws
2
c.
Wire nuts
2
d.
2
e.
Flat washers
7
f.
Spring washers
3
g.
Blade kit
4
h.
Pull chains (wood tassels) 2
i.
Balance kit
1set
Blade holder screws
4
INSTALLING MOUNTING BRACKET
Shut the power off at the circuit breaker box before beginning.
Warning: Failure to disconnect power supply prior to installation may result in serious injury.
For safety and best operating results, installation must be undertaken by qualified electrician.
Before installing the fan make sure the outlet box is properly installed to house structure.
Ensure the metal outlet box is securely fastened by at least two points to a structural ceiling
member, a loose box will cause the fan wobble.
Secure mounting bracket to outlet box by tightening mounting bracket screws & spring washers.
If not mount to ceiling outlet box, use wood screws and flat washers and mount securely to
ceiling beam. Note: Do not mount directly to sheet rock or ceiling tiles.
The ceiling fan must be installed in a location with a minimum of 18” spacing from the tip
of the blade to the nearest objects or walls.
Secure the mounting bracket to the ceiling joist or structure that is capable of carrying
a load of at least 40kgs, use two wood screws provided.
BEAM must be able to support up to 40kg.
120V Wires
Mounting bracket screws
UL Listed
Outlet box
Ground wire
Washers
Note: Picture is for representation only and
do not represent the actual bracket.
WARNING:
TO REDUCE THE RISK OF FIRE,
INJURY. MOUNT FAN ONLY ON AN OUTLET
BOX OR SUPPORTING SYSTEM MARKED
“ACCEPTABLE FOR FAN SUPPORT”.
5
DOWNROD / BALL ASSEMBLY
Slide the canopy and yoke cover on the downrod. Thread the power wires from the fan through
the canopy, and downrod (take extra care not to pull power wires damage).
Set downrod into yoke. Rotate until the holes match.
Insert connector bolt through the holes. Be careful not to damage wiring.
Tighten the two downrod set screws to make sure the fan run stable.
HANGING THE FAN MOTOR ASSEMBLY
Lift the fan assembly onto the mounting bracket.
Ensure the notch of the ball joint is positioned on the stopper of the mounting bracket to
prevent the fan from rotating when in operation.
Mounting bracket
Stopper of bracket
Notch of ball joint
Canopy
Coupling cover
Lock pin
Cross bolt
Downrod
Security screw
6
MAKING ELECTRICAL CONNECTIONS
(Fig.A)
Connect Black(Hot) fan wire to Black outlet wire,
white (Neutral) fan wire to white outlet wire.
Connect green or bare copper wire from outlet
box to the hanger bracket and downroll ball
green ground wires together. (Fig.A)
If an additional blue lite kit wire is present,
then also connect the blue wire to black wire.
Secure all connections with electrical tape.
Make sure there are no loose strands or
connections.
Follow the steps below to connect the fan
to your household wiring. Use the wire
connecting nuts supplied with your fan.
BEFORE YOU BEGIN, TURN OFF THE ELECTRICITY.
Step 1.
Step 2.
After completing wiring connections, turn all
splices upward and carefully push into outlet
box.
Separate blue and black wires on one side of
the outlet box, the white and green wires on
the other side.
7
ELECTRICAL CONNECTIONS (FOR OPTIONAL WALL CONTROL)
Fig. B & C
illustrate the wiring connections for
optional wall control (The wire color out of wall
control may vary, see wall control’s installation
manual for correct wire connections.)
NOTE: Only use an optional wall switch
designed for use with ceiling fans.
If you select to control the motor from a wall
switch, remember the wall switch will only turn
your fan ON or OFF. The speed can be adjusted
by pull chain.
If you select to control the light of ceiling fan
from a wall switch, you must pull the light chain
to the “ON” position.
If you select to control the speeds of ceiling fan
from a wall switch, you must set the speed switch
on ceiling fan to HIGH speed and leave it in that
setting.
(Fig.B)
(Fig.C)
Follow this wiring diagram. Fan & Wall control sold separately, choose wall dimming control
compatible with LED light only.
8
BLADES INSTALLATION
ATTACHING SWITCH HOUSING
MOUNTING PLATE
ATTACHING SWITCH HOUSING
Remove 3 screws on underside of the
motor, attach the switch housing mounting
plate by using these 3 screws.
After completing fan blades installation,
processed with this process.
Plug 9-pin connector together carefully.
Locate 3 screws on switch housing mounting
plate, attach switch housing to mounting plate
by using these 3 screws and tighten securely.
Model:1073-PC
Insert the blade screws through blade kit
and blade then secure by tightening two
blade screws.
Repeat this process to install the other
blades to the motor.
Blade holder screws
Blade
Switch Housing
mounting plate
Switch Housing
mounting plate
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels RP LIGHTING Ventilateur
RP LIGHTING
RP LIGHTING 1060 Manuel utilisateur
RP LIGHTING
RP LIGHTING 1070W Manuel utilisateur
RP LIGHTING
RP LIGHTING 1052 Manuel utilisateur
RP LIGHTING
RP LIGHTING 1021-PC Manuel utilisateur
RP LIGHTING
RP LIGHTING 1070 Manuel utilisateur
RP LIGHTING
RP LIGHTING 1076 Manuel utilisateur
RP LIGHTING
RP LIGHTING 1070W Manuel utilisateur
RP LIGHTING
RP LIGHTING 1088 Manuel utilisateur
RP LIGHTING
RP LIGHTING 1072-PC Manuel utilisateur
