Rosen Mazda 3 Manuel utilisateur

Multi-Media Navigation System Installation Guide

Installation Guide

NOTICE OF INTENDED INSTALLATION AND USE

THE ROSEN MULTI-MEDIA NAVIGATION SYSTEMS CONTAIN AN INTERNAL VIDEO PLAYER, WHICH IS

NOT INTENDED FOR VIEWING BY THE DRIVER. THE VIDEO PLAYER IS DISABLED WHEN THE

VEHICLE IS IN MOTION THROUGH A CONNECTION TO THE PARKING BRAKE.

THE INSTALLER OF THIS PRODUCT MUST INSURE THE VIDEO DISABLE CONNECTION IS

WORKING PROPERLY PRIOR TO DELIVERY OF THE VEHICLE.

IMPROPER INSTALLATION COULD DISTRACT THE DRIVER OR INTERFERE WITH SAFE OPERATION

OF THE VEHICLE, WHICH COULD RESULT IN SERIOUS INJURY OR DEATH, AND COULD ALSO

VIOLATE STATE AND/OR FEDERAL LAW.

ROSEN ENTERTAINMENT SYSTEMS DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY OR

PROPERTY DAMAGE THAT MAY RESULT FROM ANY IMPROPER OR UNINTENDED INSTALLATION

AND/OR USE.

STOP

Damage to the vehicle may occur

Do not proceed until process has been completed

CAUTION

Process must be carefully observed in order to reduce the

risk of damage to the accessory or vehicle

CRITICAL

Process must be carefully observed in order to ensure a

quality installation

TOOLS and EQUIPMENT

Specific tools and equipment recommended for this

process

SAFETY RISK

Observe safe practices, this process can be dangerous and

there is a risk of personal injury

TESTING and TROUBLESHOOTING

Content specific testing and troubleshooting points

DS-MZ1010 Mazda 3

Installation Guide Mazda 3

Installation Guide DP-MZ1014 Rev A

Page 2

PREPARING FOR THE INSTALLATION

Before you start, please read these critical steps below

STEP

BEFORE YOU START THE INSTALLATION,

READ THIS GUIDE!

VISIT

Rosen Dealer Central

For the latest Updates, Corrections and Technical Tips

about this product and installation

www.RosenDealerCentral.com

CHECK THE BATTERY

Test the battery voltage to make sure it’s fully charged to a

minimum of 12.8 VDC

This only takes seconds and can save hours of

troubleshooting later.

TURN THE VEHICLE

OFF

Keep the Vehicle Off during the installation to avoid setting

various Vehicle Fault sensors

Keep the Vehicle OFF during the

installation

Failure to follow this may cause the AIRBAG FAULT

SENSOR to become enabled. Dealer Service Departments

charge a significant fee to reset the Fault Sensor.

Installation Guide Mazda 3

Installation Guide DP-MZ1014 Rev A

Page 3

REMOVE THE FACTORY RADIO

You will need to remove multiple interior trim components prior to removing the factory radio.

The following steps will help guide you through this process.

STEP

Protect Dash And Radio

Protect vehicle dash from any scratches that can occur

during removing/installing radio

Remove Upper Vent Assembly

Carefully remove upper vent assembly using thin pry tool

CAUTION

Remove Radio Mounting Screws

Carefully remove 2 x phillips radio mounting screws on top

of radio

Remove Factory Radio

Carefully remove factory radio being careful not to damage

dashboard

CAUTION

Installation Guide Mazda 3

Installation Guide DP-MZ1014 Rev A

Page 4

LOCATING REMOTE COMPONENTS

You will need to mount the GPS and Optional Satellite Radio Antennas on the exterior of the vehicle.

And mount the iPod Interface Connector in the vehicle. The following steps will help guide you

through this process.

STEP

Use Caution around SRS Components

It is the installer’s responsibility to ensure that the safety

equipment in the vehicle is NOT adversely affected by installation

of this system. Ensure that the routing of the harnesses do NOT

obstruct airbags, SRS or other safety devices.

Mount the GPS and Sat Radio antenna in a

location on the exterior of the Vehicle

Route the GPS harness away from other power harnesses in the

vehicle.

This will help to ensure optimum performance of the GPS system.

“OPTIONAL”

Install the iPod interface connector in a

location accessible to the end-user

Locate the iPod interface module in an area which can be

serviced in the future.

The iPod cable is intended to be a serviceable item, which plugs

into the iPod/Sat radio Interface Module.

Install The Rosen Navigation System

You will need to prepare the Rosen Navigation System for installation in the vehicle

STEP

Remove the DVD Transport Screws

There are 2 x Phillips Transport Screws which protect the DVD

Mechanism during transportation.

Transport Screws must be removed prior to installation.

Installation Guide Mazda 3

Installation Guide DP-MZ1014 Rev A

Page 5

Connect the Power and GPS Harnesses

The GPS Harness must be tightened with a WRENCH to ensure

it is properly seated.

Be sure to use white cable clamp to secure GPS antenna cable

Failure to follow this step may result in poor GPS signal

Connect Optional Harnesses such as iPod,

Satellite Radio, Camera, Reverse Sensors

These harnesses must be fully engaged prior to the system

installation.

See the Harness Diagrams for more information

Prepare the Vehicle side harnesses for

connection to the Rosen Harness

Use care not to pinch or damage cables as this will cause

performance issues/failures

CAUTION

Mount Rosen Navigation into Dash

Insert Rosen Navigation System Into Dash and re-install

radio mounting screws that were removed. Reinstall radio

trim bezel removed in step 2

Turn the vehicle ON and confirm the unit is

fully operational

With the connectors Fully Engaged, turn the vehicle on

and press the RESET for 5 seconds on the unit.

Insert a DVD to confirm the Video Disable

Circuit is properly Operating.

The Brake Wire must be connected to the Park Brake

Indicator Wire to complete a ground when the brake is

engaged.

Installation Guide Mazda 3

Installation Guide DP-MZ1014 Rev A

Page 6

RE-INSTALL THE TRIM COMPONENTS

You will need to reinstall all trim components

STEP

Re-Install Upper Vent Assembly

Carefully re-install upper vent assembly

CAUTION

ENABLE INSTALLER SETTINGS

You will need to select certain Installer Setting based on any Optional Equipment that you may have

installed

STEP

Launch the Installer Setting Screen

From any screen with the Menu Button, follow these steps

to display the Installer Setting Screen, select:

1) From any Screen, select “Menu”

2) From the Menu Screen, select “Settings”

3) Press “Keypad,” Press “7253” and “Enter”

Select the individual Settings as needed for

the installed components

Selectable options vary by product and installation. Select

the options as applicable for the installed optional

components.

Installation Guide Mazda 3

Installation Guide DP-MZ1014 Rev A

Page 7

Perform Pre-Delivery Tests

You will need to perform several Pre-Delivery Tests to ensure customer satisfaction

Some optional equipment may not be applicable

STEP

Turn the vehicle ON and System ON

Confirm the unit starts up properly

Troubleshooting

1) Reset the System while the Vehicle is ON

2) Confirm all connectors are properly installed

3) Check the Vehicle and System Fuses

Select RADIO as the Source

Confirm that the AM and FM reception are as expected

Troubleshooting

1) Confirm Antenna is properly connected.

2) Reset the System

Select SATELLITE RADIO as the Source

Confirm Channel 001 is present after ~5 minutes

Troubleshooting

1) Confirm the SAT Radio is Turned ON in the Installer Settings

2) Confirm the antenna has unobstructed view of the Sky

3) Confirm the antenna is located on the outside of the vehicle

Select iPOD as the Source

Confirm iPod is communicating and playback is OK

Troubleshooting

1) Confirm iPod Version Compatibility – not all are compatible

2) Confirm the harnesses are properly engaged

3) Reset the System

Select CD as the Source

Confirm CD audio playback is OK

Troubleshooting

1) Confirm the Disc is Store Bought and in good condition

2) Reset the system

Installation Guide Mazda 3

Installation Guide DP-MZ1014 Rev A

Page 8

Select DVD as the Source

Confirm DVD video playback is OK

Troubleshooting

1) Ensure the Park Brake is set to view video

2) Confirm the Disc is Store Bought and in good condition

3) Reset the system

Select MP3 as the Source

Confirm MP3 playback is OK – Select Favorites

Troubleshooting

1) Confirm that a Test Track exists in the Favorites Folder

2) Reset the system

Select Phone as the Source

Confirm Phone Pairing is successful

Troubleshooting

1) Confirm the Phone has BT and is in discoverable mode

2) Confirm the Phone is compatible with the system

3) Reset the system

Select NAV as the Source

Confirm the Navigation loads and signal strength is OK

Troubleshooting

1) Confirm the antenna has an unobstructed view of the sky

2) Confirm the antenna is located on the outside of the vehicle

3) Confirm the antenna connection is properly tightened

Select Reverse Camera

Confirm the backup camera screen shows in reverse

Troubleshooting

1) Confirm the Camera is set to ON in the Installer Settings

2) Confirm the Reverse Trigger wire is attached properly

3) Confirm the Camera is receiving 12VDC as required

Installation Guide Mazda 3

Installation Guide DP-MZ1014 Rev A

Page 9

Service and Optional Parts List

Part Number Description Part Number Description

DP-MZ1011 Quick Reference Guide DP-MZ1012* Harness, Main Interconnect

DP-MZ1014 Installation Guide DP-MZ1013* Harness, Steering Wheel Cntls

DP-1047 GPS Antenna Windshield Mount DP-1001 Manual, Owner’s

DP-1008 Harness, AUX Out DP-1003 Manual, Navigation

DP-1009 Harness, AUX IN DP-1004 Remote Control

DP-1010** Harness, Sensors/Camera DP-1023 Pin, Stylus

DP-1011 Harness, Dolby 5.1/Amp DP-1020-H11 Card, SD w/ maps

DP-1022 Antenna, GPS DP-1054**** Sirius Tuner Kit

DP-1055*** Sirius Tuner/iPod Multimedia Kit DP-1053 Harness, Sirius/iPod

DP-1066 Camera, License Plate Black DP-1007 Harness, USB Adaptor

DP-1067 Camera, License Plate Chrome DP-1051 Harness, Sirius Interface

DP-1068 Camera, Universal Black DP-MZ0715 Harness, Antenna Adaptor

* DP-MZ1012/DP-MZ1013 are integrated into same harness

** Included with DP-1066, DP-1067, and DP-1068

*** Kit consists of DP-1053 iPod/Sirius combo cable and Sirius Tuner/antenna

****Kit consists of DP-1051 Sirius only cable and Sirius Tuner/Antenna

Main Harness Diagram

Installation Guide Mazda 3

Installation Guide DP-MZ1014 Rev A

Page 10

Optional Harness Diagram

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Rosen Récepteur de voiture

Rosen

Rosen RE8169D Manuel utilisateur

Rosen

Rosen AV8900H Manuel utilisateur

Rosen

Rosen XR1020U Manuel utilisateur

Rosen

Rosen DS-MZ0750 Manuel utilisateur

Rosen

Rosen DS-GM1010 GM Series Manuel utilisateur

Rosen

Rosen A10 Manuel utilisateur

Rosen

Rosen 410X Manuel utilisateur

Rosen

Rosen RE1043D Manuel utilisateur

Rosen

Rosen T10 Guide de référence

Rosen

Rosen In-Dash Multi-Media System Manuel utilisateur

Rosen

Rosen ClearVue II Manuel utilisateur

Rosen

Rosen AV7000 Guide de référence

Rosen

Rosen ClearVue II Manuel utilisateur

Rosen

Rosen DS-HD0710 Manuel utilisateur

Rosen

Rosen ZE0800D Manuel utilisateur

Rosen

Rosen DS-VW0710 Manuel utilisateur

Rosen

Rosen XR1020U Manuel utilisateur

Rosen

Rosen R6400V Manuel utilisateur

Rosen

Rosen G10 Manuel utilisateur

Rosen

Rosen RE9269D Manuel utilisateur

Rosen

Rosen DS-TY1080 Manuel utilisateur

Rosen

Rosen X10 Manuel utilisateur

Rosen

Rosen DS-TY1070 Manuel utilisateur

Manuels Récepteur de voiture populaires d'autres marques

Motorola

Motorola VWA63 Manuel utilisateur

Nextar

Nextar D3201 Manuel utilisateur

Alpine

Alpine CDE-163BT Manuel utilisateur

Pioneer

Pioneer DEH-P645R Manuel utilisateur

Axxera

Axxera XDMA7600 Mode d'emploi

XM OnyX Manuel utilisateur

Sound Storm

Sound Storm STM93R Manuel utilisateur

Soundstream

Soundstream VIR-5000 Manuel utilisateur

Avson

Avson MKT Platform Manuel utilisateur

Sony

Sony MEX-1HD - Audio Library System Manuel utilisateur

Pioneer

Pioneer DVH-P500UB Manuel utilisateur

JVC

JVC KD-AHD69 Manuel utilisateur

Blaupunkt

Blaupunkt SANTIAGO CR 87 Manuel utilisateur

Sony

Sony CDX-4160 - Cd Receiver Manuel utilisateur

XFIRE AUDIO

XFIRE AUDIO BMW42S Manuel utilisateur

VDO

VDO CD 2253 Manuel utilisateur

Volvo

Volvo 13 84 580 Manuel utilisateur

ZENEC

ZENEC ZE-160DVD Manuel utilisateur