Rosco X24 Manuel utilisateur
www.rosco.com
X24 Projector
Original Instructions
(Revision: Feb2015)
TABLE OF CONTENTS
Introduction........................................................................................................................... 3
Warnings ................................................................................................................................ 4
Modules .................................................................................................................................. 6
Base Unit .........................................................................................................................................................6
Wheel Module...............................................................................................................................................8
Lens Module ................................................................................................................................................10
Analog Control Panel................................................................................................................................11
Preparing for Use................................................................................................................. 12
Installing the Lamp (Base Unit).............................................................................................................12
Installing a Glass Pattern (Wheel Module) .......................................................................................13
Installing a Lens Barrel (Lens Accessory) ...........................................................................................14
Unit Operation (Analog,Wheel, Lens) ................................................................................ 15
Mounting .....................................................................................................................................................15
Powering Up................................................................................................................................................15
Adjusting Brightness ...............................................................................................................................16
Adjusting Focus..........................................................................................................................................16
Adjusting Wheel Speed and Direction ..............................................................................................16
Adjusting Shutters on the Wheel Module.........................................................................................16
DMX Control Module........................................................................................................... 17
Dowser...........................................................................................................................................................18
Manual Mode ..............................................................................................................................................19
DMX Mode ...................................................................................................................................................20
Troubleshooting .................................................................................................................. 22
Specifications....................................................................................................................... 24
Mechanical Specifications ......................................................................................................................24
Electrical Specifications ...........................................................................................................................24
Wheel Module Specifications................................................................................................................24
Lamp Specifications..................................................................................................................................24
Lens Module Specification .....................................................................................................................24
Warranty............................................................................................................................... 25
Certificate of Conformity .................................................................................................... 26
2X24 PROJECTOR ORIGINAL INSTRUCTIONS
www.rosco.com 3
INTRODUCTION TO YOUR X24 PROJECTOR
Congratulations on your purchase of the Rosco Laboratories X-24 Projector. (Also known as the
X-Effects).
This modular projector is intended to provide a range of unique lighting effects with high
brightness in a compact package.
These effects include, but are not limited to, light reflecting off water and fire of varying
intensities.
A variety of lenses provide a wide range of beam angles suitable for any situation.In reality,the
effects are limited only by your imagination.
WARNINGS
The light beam near the front of the unit (< 1m / 3.3 ft.) is very
concentrated.
Make sure that no object or person comes into the light beam at this range as
burns or fire may result.
The top lid of the unit may become hot to the touch during operation.
Contact during or immediately following operation may result in burns.
The lamp is subject to high temperatures and pressures during operation. Do
not attempt to operate unit with lid open. Also do not attempt to handle lamp
within 1 hour of operation.
High voltages are produced when the unit attempts to strike the lamp. Only
apply power to the unit when a lamp is attached properly seated in the unit,
and the lid is closed.
High voltages and stored energy are present inside the unit. Only trained
service personnel should engage in repairs or replacements beyond the
modules or lamp.
At very cold temperatures the lamp may need to warm up close to room
temperature before it will properly strike.
The use of a safety cable is strongly recommended when hung overhead. Also
make sure not to block the top, bottom, or rear vents when mounted during
operation.
Ventilation openings are not to be obstructed during the operation of the
appliance.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children shall be supervised to ensure that they do not play with the appliance.
4X24 PROJECTOR ORIGINAL INSTRUCTIONS
www.rosco.com 5
This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without
supervision.
Disconnect The X24 from power before maintenance, servicing or replacing
parts.
Units in outdoor settings may need to be shielded from the elements and/
or heated. There are commercially available enclosures that can serve this
purpose, please call Rosco for more information. 1-800-767-2669.
6X24 PROJECTOR ORIGINAL INSTRUCTIONS
Yoke Tilt Knob Yoke
Cap Screw
MODULES
Base Unit
The base unit contains the lamp, electronic ballast, and accessory power supply. The yoke
attaches to the side of the base unit in slots for positional adjustment. It also has a slot for
special optical filters.
Note: In older versions of the X24 an aspherical lens was fitted behind the front plate.
If this lens is fitted please note when handling the base unit alone, be aware that it extends
slightly beyond the front plate, and is subject to being scratched.
SIDE VIEW
BACK VIEW
Line
Connection Fan
Top Lid
Power Switch
Control Panel -
Analog or DMX
www.rosco.com 7
TOP VIEW
Lamp
Special Optics Slot
Lamp Mount
Lamp Clip
8X24 PROJECTOR ORIGINAL INSTRUCTIONS
Wheel Module
The wheel module is made up of motors for rotating two overlapping glass patterns.
It also has four shutters and a slot for placing an E-size gobo.
Note: In older versions of the X24 the glass discs were made to a thinner specification.
These should not be used in the latest version of the unit as this may result in damage to the
drive pulley.
BACK VIEW
Top Lid
Bottom Lid
Connector
Alignment
Pin
Motor
www.rosco.com 9
FRONT VIEW
FRONT VIEW (with wheels fitted)
Idler Wheel
Pull Tab
Glass Pattern
(Standard Water)
Top Shutter
(Not in View)
Bottom Shutter
(Not in View)
Drive Pulley
Side Shutter
Side Shutter
Damper
10 X24 PROJECTOR ORIGINAL INSTRUCTIONS
Lens Module
The lens module provides the mounting for the various lens barrels.
At the present time there are barrels available in 19°, 30°, 50° and 70° beam angles.
It provides screw focusing and a lock-down knob.
The lens barrels themselves also have a slot for inserting a dichroic filter. (See page 14).
FRONT VIEW
# 20 Screw
Lens Mount
Ring
Thumb Screw
Locking Knob
Table des matières
Autres manuels Rosco Projecteur
Manuels Projecteur populaires d'autres marques
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur
NEC
NEC NP600S EDU Manuel utilisateur
BenQ
BenQ SH753P Manuel utilisateur
Eiki
Eiki EK-623U series Manuel utilisateur
Epson
Epson PowerLite Pro Cinema 6020UB Manuel utilisateur
Epson
Epson PowerLite Home Cinema 705HD Manuel utilisateur
