Roline 12.02.1091 Manuel utilisateur
1-
USB Galvanic Isolator
User’s Manual
12.02.1091
2-
1. Introduction
USB Galvanic Isolator protects PC or Laptop while connecting USB peripherals which is wired to high voltage. This small,
industrial - grade isolator is very easy to use and provides a high-voltage barrier protection against surges, noise and ground
loop errors. It is suitable for use in sensitive applications like automotive measurements.
USB isolator provides a high - voltage isolation barrier between computer and it’s connected USB device. The isolation protects
equipment from electrical over-voltages and transient voltage spikes, by eliminating ground loop currents flowing between the
PC and USB device which can cause damage and inaccurate measurements.Additionally, isolation minimizes conducted noise
from static discharge, magnetic fields and radio frequency interference.
USB isolator is USB bus powered and can provide 5V 300mA to your USB device with built-in isolated DC-DC converter. This is
possible only when the isolator is connected to a high power USB host port.
2. Features
USB isolation 5000V DC between USB host and USB device.
USB 2.0 compatible, 1.5Mbps low speed and 12Mbps full speed Bi-directional communication.
Short circuit protected for x D+ and x D- lines.
Isolated power supply in device through a DC-to-DC converter
Class 3A contact ESD performance per ANSI / ESD STM5.1-2007
High common-mode transient immunity :>25 kV/us
Supports Windows 98SE / ME / 2000 / XP / Vista / 7 / 8 / 8.1 / 10, Mac OS 8.6 or higher; no driver installation
required
3. Specifications
Model No. 12.02.1091
Isolation D+ & D- 5000V DC
Power 3000V DC
Transfer Rate 1.5 / 12 Mbps
Connector Host USB Type A Male
Device USB Type A Female
Cable Length 0.15 m
Operating Temperature 0°C to 50°C
LED 1
Downstream Power Up to 300mA
Power Mode Bus powered
Housing Plastic
Dimension ( L x W x H ) 66 x 39 x 20 mm
4. Connecting
Typical Application
The USB Isolator unit is installed in-line between the PC and a connected USB device.
PC
USB Device USB AM/AF Cable
USB Cable
Power LED (Orange)
3-
5. Installation
1. Plug the unit’s molded USB A male cable into the host computer or USB hub
2. The Power LED will light on, indicating power is being received from the host and the isolator is ready.
3. Plug the downstream device into the unit (Type A female connector). This USB cable is not included.
4. The USB Isolator is transparent to the host operating system and does not require configuration or software installation.
Note: The isolators are USB bus powered. When the USB Isolator is connected to a high power USB host port, it can
provide power current up to 300mA to the attached downstream device.
Regulatory Compliance
Disclaimer
Information in this document is subject to change without notice. The manufacturer does not make any
representations or warranties (implied or otherwise) regarding the accuracy and completeness of this document and
shall in no event be liable for any loss of profit or any other commercial damage, including but not limited to special,
incidental, consequential, or other damages.
No part of this document may be reproduced or transmitted in any form by any means, electronic or mechanical,
including photocopying, recording or information recording and retrieval systems without the express written
permission of the manufacturer.
All brand names and product names used in this document are trademarks, or registered trademarks of their
respective holders.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Roline Matériel réseau
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
