Roland HB-12 Manuel utilisateur
DSA121
DYX362
Mode indicator
*1
• Light: Press the [Preheat] key to start preheating
• Flashing: Preheating under way
• Off: Preheating completed
Tray
Printer
(BT-12)
Finisher
(This machine HB-12)
Front Cover
Mode Switching
Lever
Time/temperature indicator [Temperature] key [Preheat] key*1 [Power] key
[Time] key [Stop/Unlock] key
Control Panel
Guide to Components of the Finisher
This guide describes the basic printing procedures using the
printer and this machine. In the next pages, the procedures
for each step and particular cautions are explained.
For safe and correct use, be sure to read Safety Information
before using the machine.
Quick Guide
Basic Usage of the Finisher
CAUTION:
• A parent or guardian must be present if infants, children, or people who need assistance use the ma-
chine, and they should be very careful when using it. Otherwise, injury or burns may result.
The finisher has “Standard mode”, “Professional mode”, and “Professional 2 mode”.
◆Standard mode
The factory-default setting is standard mode. The finisher has the following functions
to prevent children from touching the inside of the finisher accidentally when it is very
hot.
• When the inside of the finisher exceeds 70 °C (158 °F), the front cover locks. To
open the front cover, press the [Stop/ Unlock] key for at least 1 second.
The surface of the heater and the fabric are not in contact with each other during the
fixing process, so the surface of the heater does not become dirty.
◆Professional mode
To use this mode, switch from standard mode.
As this mode is for users who are accustomed to using the finisher, the front cover
does not lock even when the temperature of the inside of the finisher exceeds 70 °C
(158 °F).
However, during press processing and fixing processing, the front cover locks regard-
less of whatever mode is used to prevent erroneous operations.
The surface of the heater and the fabric are not in contact with each other during the
fixing process, so the surface of the heater does not become dirty.
◆Professional 2 mode
This mode minimizes the loss of color when T-shirts are washed.
To use this mode, switch from professional mode.
As this mode is for users who are accustomed to using the finisher, the front cover
does not lock even when the temperature of the inside of the finisher exceeds 70 °C
(158 °F).
However, during press processing and fixing processing, the front cover locks regard-
less of whatever mode is used to prevent erroneous operations.
The surface of the heater and the fabric are in contact with each other during the fixing
process, so regular cleaning of the surface of the heater is necessary.
* Refer to Operating Instructions for cleaning frequency and precautions.
◆How to Switch Modes
Press the [Temperature] key and
[Time] key simultaneously for at least
2 seconds.
DYX353
The operating mode changes as fol-
lows.
Standard mode
Professional
2 mode
Professional
mode
DYX354
◆Unlock Cover
When set to standard mode, press
the [Stop/ Unlock] key for at least 1
second.
DYX360
When set to the professional mode,
it is not necessary to hold down the
[Stop/Unlock] key.
Operating Procedure
Perform the procedures in the order of 1, 2, 3, and then 4.
The following settings and procedures are examples for major fabrics.
Depending on your environment, discoloration may occur or the ink may not be fixed prop-
erly. Before configure the settings, check the fixability of the fabric you use.
Fabric type Mode Temperature 1. Preparation 2. Pressing 3. Printing 4. Fixing
T-shirt Standard mode
Professional
mode
170°C (338°F) See next
page.
30sec See BT-12
Operating
Instructions.
3min
Professional 2
mode
180°C (356°F) 30sec 30sec
3min
Tote bag (thick) Standard mode
Professional
mode
170°C (338°F) 30sec 3min
Tote bag (thin) 150°C (302°F) 30sec 3min
Sweatshirts 170°C (338°F) 30sec 3min
© 2018 Roland DG Corporation
Printed in Japan
EN GB EN US EN AU J089-7032
R1-181105 FA01418
Preparation
Loading the fabric in the tray
For details, refer to User’s Guide provided with the printer BT-12.
You can shorten the processing time by putting a garment in the tray while preheating the
finisher.
➊
Press the [Power] key to turn on the power..
➍
Set the amount of time that the heater is on.
Set the time according to the fabric on which you
are printing. The default setting is “Medium”.
➋
Make sure the mode switching lever is set in the
center.
➎
When the [Preheat] key is lit, press the [Preheat]
key to start preheating.
When the [Preheat] key is unlit, no operation is
necessary because preheating is completed.
➌
Set the temperature of the heater.
Set the temperature according to the fabric on which
you are printing. The default setting is “High”
Procedure for ( )
➊
When you move the mode switching lever to the
left, processing starts. An alarm sounds after pre-
heating is completed.
➋
Procedure for ( )
➊
When you move the mode switching lever to the
right, processing starts. An alarm sounds after
preheating is completed.
➋
Autres manuels Roland Imprimante
Roland
Roland TrueVIS SG3-540 Manuel utilisateur
Roland
Roland CX-500 Manuel d'installation et d'exploitation
Roland
Roland CAMM-2 PNC-2300 Manuel de la liste des pièces
Roland
Roland VersaEXPRESS RF-640 Manuel d'utilisation et d'entretien
Roland
Roland Texart XT-640 Manuel utilisateur
Roland
Roland VersaUV LEF2-300 Manuel utilisateur
Roland
Roland TrueVIS MG-640 Manuel utilisateur
Roland
Roland TrueVIS SG3-540 Manuel utilisateur
Roland
Roland Metaza MPX-90 Manuel utilisateur
Roland
Roland METAZA MPX-70 Manuel utilisateur
Roland
Roland CAMM-2 PNC-2300 Manuel utilisateur
Roland
Roland XR-640 Manuel utilisateur
Roland
Roland VersaUV LEF2-200 Manuel d'utilisation
Roland
Roland PC-600 Manuel utilisateur
Roland
Roland VersaEXPRESS RF-640 Manuel utilisateur
Roland
Roland SJ-745EX Guide de démarrage rapide
Roland
Roland VersaUV LEF2-300 Manuel d'utilisation et d'entretien
Roland
Roland VersaStudio BR-20 Manuel d'utilisation et d'entretien
Roland
Roland VS-640 Manuel utilisateur
Roland
Roland XC-540MT Manuel utilisateur
