RODE Microphones VideoMic Manuel utilisateur

80Hz

VideoMicTM

Parts Guide

Mic Controls

quickstart

guide

VideoMicTM

www.rodemic.com

1. Foam windshield

2. Camera shoe mount

3. Battery cover

4. PAD switch (inside battery compartment)

warranty.rodemic.com/videomic

Scan the QR code to

Don’t FORGET

to register for your

FREE ten year warranty!

The RØDE VideoMicTM features an integrated

shock mount based on Rycote®Lyre®technology.

Constructed from a single piece of hard-wearing

thermoplastic, the Lyre®provides superior acoustic

suspension to traditional elastic solutions,

and will never wear out, sag or snap.

RØDE SOUNDBOOTH

now for Broadcast mics

Hear and compare RØDE microphones

at www.rodemic.com/soundbooth or on your iPad®

5. LED power indicator

6. Power and HPF switch

7. Integrated Rycote®Lyre®suspension

8. 3.5mm dual mono output cable

The High Pass Filter (HPF ) is a low frequency cut-off setting, which you can use

to remove rumble, camera noise or other low frequency noise while recording.

Mic ON

using High Pass Filter

Mic ON

Flat setting

Battery OFF

Mic mute

LED power

indicator

028_952_1_Videomic_Quickstart.indd 1028_952_1_Videomic_Quickstart.indd 1 17/12/2012 8:45:19 AM17/12/2012 8:45:19 AM

0dB

-10dB

-20dB

The LED power indicator next to the

On/Off switch will turn red when the

battery is running low. The mic will

work for approximately one hour once

the red indicator is lit, however with

reduced performance.

1. Turn the tightening ring counter-

clockwise to loosen the camera shoe

connection, before attaching to camera.

Securing the cable will

eliminate undesired noise

caused by cable movement.

The cable can be secured

in one of two orientations,

depending on the location

of your camera’s “Audio In”

socket.

See diagram 1 for cameras

with mic socket on the left.

See diagram 2for cameras

with mic socket on the right.

2. Slide the camera-shoe into place on the

camera mount. When the mic is in place,

secure it by gently tightening the ring

clockwise.

3. Connect the VideoMic’s audio lead to

the camera’s “Audio In” or “Mic” socket,

and secure the cable in place using the

in-built cable clips (see below).

mounting to camera

securing the cable

PAD switchbattery

The VideoMic comes with a three-position

PAD switch which is located inside the battery

compartment.

The PAD provides a selectable 10 or 20db

reduction of the input sensitivity, reducing

the output level when recording loud sound

sources, so that the optimal level can be

achieved in a wide range of situations.

To change the battery, gently push

and slide the battery cover off. Insert a

standard 9V battery with the positive

(+) end upwards.

The VideoMic uses a standard 9V

battery. With a good quality Alkaline

or Lithium battery, the VideoMic will

run for up to 100 continuous hours. We

recommend you remove the battery

if storing your VideoMic for extended

periods without use.

–

Push the cable in from the bottom.

028_952_1_Videomic_Quickstart.indd 2028_952_1_Videomic_Quickstart.indd 2 17/12/2012 8:46:21 AM17/12/2012 8:46:21 AM

Autres manuels pour VideoMic

Ce manuel convient aux modèles suivants

Autres manuels RODE Microphones Microphone

RODE Microphones

RODE Microphones NT2000 Manuel

RODE Microphones

RODE Microphones NTG-2 Manuel utilisateur

RODE Microphones

RODE Microphones NT1 Manuel

RODE Microphones

RODE Microphones NTK Manuel

RODE Microphones

RODE Microphones NTV Manuel utilisateur

RODE Microphones

RODE Microphones Procaster Manuel utilisateur

RODE Microphones

RODE Microphones Classic II Manuel

RODE Microphones

RODE Microphones HS2 Manuel utilisateur

RODE Microphones

RODE Microphones WIRELESS GO Manuel utilisateur

RODE Microphones

RODE Microphones NT1000 Manuel utilisateur

RODE Microphones

RODE Microphones NTG-2 Manuel utilisateur

RODE Microphones

RODE Microphones NT2000 Manuel utilisateur

RODE Microphones

RODE Microphones M1-S Manuel utilisateur

RODE Microphones

RODE Microphones NT55 Manuel utilisateur

RODE Microphones

RODE Microphones PODCASTER Manuel utilisateur

RODE Microphones

RODE Microphones M2 Manuel utilisateur

RODE Microphones

RODE Microphones NT4 Manuel

RODE Microphones

RODE Microphones VideoMic Me-C Manuel utilisateur

RODE Microphones

RODE Microphones NT 3 Manuel

RODE Microphones

RODE Microphones NTG8 Manuel utilisateur

RODE Microphones

RODE Microphones NT2-A Manuel utilisateur

RODE Microphones

RODE Microphones NT2-A Manuel utilisateur

RODE Microphones

RODE Microphones STEREO VIDEOMIC PRO Manuel utilisateur

RODE Microphones

RODE Microphones NTK Manuel utilisateur

Manuels Microphone populaires d'autres marques

IK Multimedia

IK Multimedia iRig Stream MIC PRO Manuel utilisateur

DAPAudio

DAPAudio RM-101 Manuel utilisateur

AKG

AKG CHM 21 Manuel utilisateur

Sennheiser

Sennheiser evolution wireless series EM 100 Manuel utilisateur

Sony

Sony C-48 Manuel utilisateur

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Manuel utilisateur

Shure

Shure WH30TQG Manuel utilisateur

auna PRO

auna PRO MIC-900 Manuel utilisateur

AKG

AKG D 3800 Manuel utilisateur

Shure

Shure KSM141 Manuel utilisateur

MAIIN SOUND

MAIIN SOUND IIN style Manuel utilisateur

Earthworks

Earthworks TC25 Manuel utilisateur

Sennheiser

Sennheiser evolution D1 Manuel utilisateur

Alesis

Alesis MicLink Wireless Manuel utilisateur

DSPPA

DSPPA D6234 Manuel utilisateur

Monacor

Monacor IMG STAGELINE ECM-300B Manuel utilisateur

Ansr Audio

Ansr Audio Scan16 Manuel utilisateur

Shure

Shure MXA710 Series Manuel utilisateur