RODE Microphones NT 2 Manuel

NT 2

Instruction Guide

RØDE STUDIO CONDENSER MICROPHONES

RØDE NT2

Serial Number: ……………………

Checked by: ………………………

Date: ………………………………

Thank you for purchasing a RØDE NT 2. This

precision microphone will, if you follow the basic

operational/storage information, give you years of high

performance, trouble free service.

RØDE is part of the Freedman Group of Companies

which was founded by the late Henry Freedman. Henry

was born in London England, emigrating to Stockholm

Sweden in the early 50’s where his career as an

Electronics Engineer began. In 1966 he moved his

family to Australia and established Freedman

Electronics, a pioneer in the Professional Audio Industry.

The Company Headquarters are in Sydney Australia,

home of the 2000 Olympic games. There are divisions

that import and distribute professional audio products,

and others that design and manufacture speaker

systems, amplifiers and associated electronics.

The NT 2 is part of a growing family of microphones and

accessories backed by over forty years of experience in

Professional Audio, and is the result of a two year

research and development program. Each microphone

is hand assembled in Australia using imported and

locally produced parts. The electronic components used

were selected not only for their reliability and technical

specification, but extensive listening tests were also

carried out to gauge their sonic qualities before being

included.

All wiring and solder is of Hi-Fi Industry grade and all

connecting points are Gold plated as well as being

treated with Deoxidizing Solution. The PCB’s are

sprayed with a Conformal, and the above procedures

assure long term immunity to signal degrading

corrosion.

Each microphone is ‘soak tested’ for 24 hours prior to its

final test.

We are proud of this microphone, and hope that you

are, and remain fully satisfied with your purchase.

Peter Freedman

RØDE Australia

SPECIFICATIONS:

Capsule: Dual pressure gradient

transducers.

Frequency Response: 20 - 20,000 Hz

Noise: 17dB-A SPL

Sensitivity: 16 mV/Pa

Max SPL: 135dB – 145 with pad.

Output Impedance: 200W

Power Requirement: 48V D.C.

Current Consumption: 3.5ma.

Weight: 530 gm

Features:

•Large Capsule with gold plated membrane.

•Low-Noise, transformerless circuitry.

•Omni and Cardioid polar patterns.

•High Pass Filter.

•-10db Pad.

•Full Frequency Response.

•Gold Plated Output Connector and internal

head pins.

•Designed and Manufactured in Australia.

The NT2 comes complete with:

•Flight Case.

•Shock Mount (SM-1).

•Windshield (WS-2).

•2 Spare SM-1 Rubber Bands.

•Guarantee and Instruction Guide.

•Pack of Moisture-Absorbing Crystals.

The NT2-NC comes complete with:

•Zip Pouch (ZP-1)

•Shock Mount (SM-1).

•2 Spare SM-1 Rubber Bands.

•Guarantee and Instruction Guide.

•Pack of Moisture-Absorbing Crystals.

When you open the storage box for the first time,

check that you have all the accessories listed.

•Before connecting and using the NT2 please

take a few minutes to read these instructions.

1. You will need a power supply to operate the

NT 2. For optimum results, this should be a

48V D.C. supply.

Most professional mixing consoles have an

internal 48V supply, or you can purchase

a separate supply. Make sure the power

supply you use is a professional unit that is

operating correctly. Damage due to

connection of the NT 2 to a faulty power

supply is not covered by the guarantee.

2. Set the polar pattern switch to your desired

setting either omni or cardioid.

Set the response switch to your desired

setting either flat response or low frequency

cut.

This switch also allows for a 10 db pad to be

inserted into the signal path which allows for

very high SPL operation.

3. The NT 2 comes complete with a shock

mount suspension device (SM 1). Connect

the shock mount to a stable microphone

stand (studio mic’s do not like to be dropped!).

The shock mount pivot screw should be

tightened (by hand) when you have

positioned it at the appropriate angle. To fit

the NT 2, grasp the two levers located

centrally and push them inwards, this will

open up the suspension and the NT 2 can be

placed in the mount.

4. When first connecting the NT 2 to a mixing

console we suggest that you have the gain

control adjusted to full attenuation.

5. Please make all cable connections before

applying power to the microphone. Never

remove the microphone cable while the power

is connected.

6. Check that you have the NT 2 correctly

connected. You can connect the microphone

directly into the mixer without an external

supply if 48V is available on the mixer.

Always use a balanced (3 pin XLR style)

microphone cable. Note: Ensure that the

cable is a wired pin 1 screen, pin 2+ pin 3-.

We suggest you purchase a lead with gold

plated plugs, as contact resistance due to

corrosion is a major cause of problems in all

sound systems. Note: All contact points on

the NT 2 are gold plated.

7. Switch the power supply/mixer on. The

microphone will take about six seconds to

stabilise. Adjust the mixer gain so that the

Peak light flashes on the peaks of the program

source to be recorded (Voice or Instrument).

You are now ready to use the microphone.

8. Microphone technique, or how to get the

sound you want requires experimentation.

We suggest that you start with the channel

EQ set to ‘off’ or flat (no boost or cut). Try to

get the sound you are after by changing the

mic’s position using either the omni or

cardioid selection (depends on application),

and/or by placing either reflective or

absorbent panels at various angles adjacent

to the source being recorded. Changing the

acoustic properties of the space the

microphone is in, is our recommended initial

approach for obtaining the best sound quality.

(Remember you can not change a room’s

acoustic properties with EQ.) After you have

the best sound quality achievable with this

approach, then equalisation and effects such

as reverb or indeed any other signal

processing can be used for enhancement,

but should be used sparingly! We have

designed the NT 2 to exhibit a rising

response centered around 12K. This

characteristic is found in many of the 50’s

classics, and is a very desirable quality in

vocal and other applications. Because of this

inherent ‘presence’, high frequency

equalisation, with its signal degrading

consequences, is not usually required to

restore clarity lost in the recording/mixing

process.

Some tips that may be helpful:

1. Condenser microphones do not like moisture!

Never take the NT 2 into the shower, never

sing in the rain or go swimming with one.

Seriously, the NT 2, like all studio mics,

should be kept dry at all times. The capsule

will be subjected to a lot of moisture in vocal

applications, and we suggest the Windscreen

be used for all vocal work.

2. Never subject the NT 2 to mechanical shock

by hitting or dropping the mic as this can

cause it to be severely damaged and is not

covered by your warranty.

3. After every use, the NT 2 should be removed

from its suspension, wiped down with a dry

soft cloth, and placed in its case. Be sure to

place the moisture absorbent crystals (white

pouch) at the head end of the mic. The

crystals will absorb any moisture present.

Eventually, this pack needs to be dried out.

When the crystals have turned pink, the pack

should be placed in an oven set to between

100 to 150oC. They will be activated when

they turn blue.

4. The body of the NT 2 is finished in a matt nickel

plating over brass. To clean the body, carefully

unscrew the bottom angled end piece, remove

the end piece, the barrel will now be able to be

removed. Place the mic back in its case while

you are cleaning the barrel.

Use a non abrasive ‘kitchen style’ solution to

clean the barrel, rinse with clean water and

then fully dry before replacing the barrel.

There is a pin guide on the end of the main

mic body that locates the barrel in the correct

position. Replace the end piece and tighten

until the barrel does not move. Be sure not to

over-tighten as this may damage the

microphone.

5. Never remove the cage that surrounds the

capsule!!! The temptation to touch the

delicate membrane will be too much to bear

and you will have ruined your microphone.

If you are rich and have ‘a few roo’s loose in

the top paddock’, and really want to do this,

go ahead, we can replace the capsule at

great cost, which of course includes renewing

your warranty that you made void by sticking

your fingers where they don’t belong.

6. Never be tempted to let the local electronics

‘genius’ modify the microphones’ electronic

circuit! Even if they guarantee to achieve

what he/she may call a ‘great improvement’

in sonic quality. At best this will void your

warranty, and at worst???

7. Never use the NT 2 as a hammer or

football.

8. Never lend the NT 2 to anyone! Tell them to

buy one of their own.

Warranty Service:

All RØDE products are warranted for one year

from date of purchase and the warranty card

should be used to register that purchase.

The warranty covers parts and labour that may

be required to repair the microphone during the

warranty period. The warranty excludes defects

caused by normal wear and tear, modification,

shipping damage, or failure to use the micro-

phone as per the instruction guide.

If you experience any problem, or have any

questions regarding your RØDE microphone,

first, contact the Dealer who sold it to you. If the

microphone requires Factory authorised service,

return will be organised by that Dealer. We have

an extensive Distributor/Dealer network, but if you

have difficulty getting the advice or assistance

you require, do not hesitate to contact us directly.

The warranty excludes defects caused by normal

wear, modification, shipping damage or failure to

use the microphone as per the instruction guide.

If you experience any problems, or have any

questions regarding your RØDE microphone, first

contact the dealer who sold it to you. If your

microphone requires factory authorised repair,

you will be given a return authorisation number

and an address where to send the unit. Please

include all accessories, your name, address and

contact number.

Except to the extent precluded by applicable

state law, the manufacturer of this product

will have no liability for any consequential,

incidental or special damages; any warranty

of merchantability or fitness for particular

purpose expires when this warranty expires.

This warranty gives you specific legal rights, and

you may have other rights which vary from state

to state.

International Tel: 61 -2 8765 9333

Fax: 61 -2 8765 9444

Australia Tel: (02) 8765 9333

Fax: (02) 8765 9444

USA: Tel: 310-328-7456

Fax: 310-328-7180

e-mail information: [email protected]

www.rodemicrophones.com

or contact your local RØDE Distributor

Table des matières

Autres manuels RODE Microphones Microphone

RODE Microphones

RODE Microphones NTK Manuel utilisateur

RODE Microphones

RODE Microphones Broadcaster Manuel utilisateur

RODE Microphones

RODE Microphones NT-USB Manuel utilisateur

RODE Microphones

RODE Microphones M1 Manuel utilisateur

RODE Microphones

RODE Microphones NTG-1 Manuel utilisateur

RODE Microphones

RODE Microphones PODCASTER Manuel utilisateur

RODE Microphones

RODE Microphones NT5 Manuel utilisateur

RODE Microphones

RODE Microphones VideoMic Manuel utilisateur

RODE Microphones

RODE Microphones M1-S Manuel utilisateur

RODE Microphones

RODE Microphones iXY Manuel utilisateur

RODE Microphones

RODE Microphones NT2-A Manuel utilisateur

RODE Microphones

RODE Microphones NT2-A Manuel utilisateur

RODE Microphones

RODE Microphones NT 3 Manuel utilisateur

RODE Microphones

RODE Microphones Broadcaster Manuel

RODE Microphones

RODE Microphones NTG-2 Manuel utilisateur

RODE Microphones

RODE Microphones NT-USB+ Manuel utilisateur

RODE Microphones

RODE Microphones NTV Manuel utilisateur

RODE Microphones

RODE Microphones STEREO VIDEOMIC PRO Manuel utilisateur

RODE Microphones

RODE Microphones S1 Manuel utilisateur

RODE Microphones

RODE Microphones STEREO VIDEOMIC PRO Manuel utilisateur

RODE Microphones

RODE Microphones NT6 Manuel utilisateur

RODE Microphones

RODE Microphones VideoMic NTG Manuel utilisateur

RODE Microphones

RODE Microphones PSA-1 Manuel utilisateur

RODE Microphones

RODE Microphones NT1A-MP Manuel utilisateur

Manuels Microphone populaires d'autres marques

IK Multimedia

IK Multimedia iRig Stream MIC PRO Manuel utilisateur

DAPAudio

DAPAudio RM-101 Manuel utilisateur

AKG

AKG CHM 21 Manuel utilisateur

Sennheiser

Sennheiser evolution wireless series EM 100 Manuel utilisateur

Sony

Sony C-48 Manuel utilisateur

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Manuel utilisateur

Shure

Shure WH30TQG Manuel utilisateur

auna PRO

auna PRO MIC-900 Manuel utilisateur

AKG

AKG D 3800 Manuel utilisateur

Shure

Shure KSM141 Manuel utilisateur

MAIIN SOUND

MAIIN SOUND IIN style Manuel utilisateur

Earthworks

Earthworks TC25 Manuel utilisateur

Sennheiser

Sennheiser evolution D1 Manuel utilisateur

Alesis

Alesis MicLink Wireless Manuel utilisateur

DSPPA

DSPPA D6234 Manuel utilisateur

Monacor

Monacor IMG STAGELINE ECM-300B Manuel utilisateur

Ansr Audio

Ansr Audio Scan16 Manuel utilisateur

Shure

Shure MXA710 Series Manuel utilisateur