Rockford Fosgate SSC-500 Manuel utilisateur

INSTALLATION MANUAL FOR

SSC-500 CONTROL SYSTEMS

ON HYDRAULIC PRESSES

IMPORTANT: PLEASE REVIEW THIS ENTIRE

PUBLICATION BEFORE INSTALLING, OPERATING OR

MAINTAINING THE SOLID-STATE HYDRAULIC PRESS

ELECTRICAL CONTROL SYSTEM.

SSC-500 Control Box

(Not Shown)

Operator Interface

Keypad/Display

5795 Logistics Parkway • Rockford, Illinois 61109 • Toll Free 1-800-922-7533 (USA only) • Phone (815) 874-7891

Fax (815) 874-6144 • Web Site: www.rockfordsystems.com • E-Mail: [email protected]

Manual No. KSL-249

Program/Run

Selector Switch

Remote Operator

Station (Optional)

Rockford Systems, LLC

2Call: 1-800-922-7533

TABLE OF CONTENTS

SSC-500 Hydraulic Press Solid-State Control

SECTION 1—IN GENERAL ..................................................3 - 9

SECTION 2—INTRODUCTION .........................................10 - 14

SECTION 3—INSTALLATION OF SSC-500 CONTROL SYSTEM

COMPONENTS ............................................................14 - 24

Literature Packetr......................................................14 - 15

Control Box ...............................................................15 - 18

Palm Button Assembly...............................................18 - 20

Foot Switch (Optional)........................................................20

Supervisory Control Station ................................................21

Presence Sensing Device...................................................21

Main Power Disconnect Switch ..........................................22

Motor Starter ....................................................................22

Custom or Special Control Box...........................................22

Flywheel and Gear Covers..................................................22

Collateral Equipment..........................................................22

Point-of-Operation Safeguards ...........................................22

Other Installation Considerations .................................23 - 24

SECTION 4—PROGRAMMING ........................................24 - 33

Setup of Control System .......................................................24

Initial Setup Procedure ........................................................24

Programming Overview.........................................................25

Clear Stroke......................................................................26

Clear Batch.......................................................................27

Batch Preset .....................................................................27

Bottom Dwell ....................................................................28

Decompress Timerl ...........................................................28

Anti-tiedown ms................................................................29

Single Return Mode...........................................................28

Asing tmr sec....................................................................29

PSDI Timer........................................................................30

Asing Mode.......................................................................30

Asing Timer ......................................................................31

User Inputs ...............................................................31 - 32

Options edit ......................................................................33

SECTION 5—PSDI ....................................................................34

SECTION 6—OPERATING CONSIDERATIONS..............................35

SECTION 7—FAULT MESSAGES ....................................36 - 37

SECTION 8—MAINTENANCE & INSPECTION..................... 38 - 39

SECTION 9—METHODS OF SAFEGUARDING ......................40 - 41

SECTION 10—LAYOUT SKETCH...............................................42

SECTION 11—RETURN AUTHORIZATION FORM......................43

SECTION 12—ORDER FORM ....................................................44

FIGURES, PHOTOS, AND TABLES

Figure 2.1 Block Diagram ........................................................12

Figure 4.1 Initial Setup Procedure Flowchart .............................24

Figure 4.2 Initial Information on Display ....................................24

Figure 4.3 Main Program Menu Flowchart ................................25

Figure 4.4 Clear Stroke Flowchart ............................................26

Figure 4.5 Clear Batch Flowchart .............................................26

Figure 4.6 Batch Preset Flowchart............................................27

Figure 4.7 Bottom Dwell Flowchart...........................................27

Figure 4.8 Anti-tiedown Flowchart............................................28

Figure 4.9 Asingle Mode Flowchart ..........................................28

Figure 4.10 Asingle Tmr Flowchart...........................................29

Figure 4.11 User Input Fault Messages Chart............................29

Figure 4.12 Input # 1 - 4 Flowchart .........................................30

Figure 4.10 Speed Change Flowchart.......................................31

Photo 1.1 Inside view of Control box...........................................8

Photo 1.2 Control box with danger labels....................................9

Photo 3.1 Standard control box with keypad/display .....................15

Photo 3.2 Inside view of standard control box ...........................15

Photo 3.3 Top view of control module with cover.......................16

Photo 3.4 Top view of control module without cover ....................16

Photo 3.5 Operator interface keypad.........................................17

Photo 3.6 Back side of keypad/display......................................18

Photo 3.7 Palm button assembly ..............................................18

Photo 3.8 Red emergency stop palm button..............................19

Photo 3.9 Yellow emergency return inch up ..............................20

Photo 3.10 Prior-action pushbutton stations..............................20

Photo 3.11 Foot switch ............................................................20

Photo 3.12 Supervisory control station......................................21

Photo 7.1 Main EPROM ...........................................................36

Table 3.1 Depth Penetration Factor ..........................................21

Table 4.1 Quick Reference Table..............................................25

Table 6.1 Fatal Fault Messages .......................................33 - 34

Table 6.2 General Fault Messages ...........................................34

SECTION 1 — IN GENERAL

SSC-500 Hydraulic Press Solid-State Control

Rockford Systems, LLC

Call: 1-800-922-7533 3

Efficient and safe machine operation depends on the development, implementation and enforcement of a safety program. This program requires,

among other things, the proper selection of point-of-operation guards and safety devices for each particular job or operation and a thorough safety

training program for all machine personnel. This program should include instruction on the proper operation of the machine, instruction on the

point-of-operation guards and safety devices on the machine, and a regularly scheduled inspection and maintenance program.

Rules and procedures covering each aspect of your safety program should be developed and published both in an operator’s safety manual, as

well as in prominent places throughout the plant and on each machine. Some rules or instructions which must be conveyed to your personnel and

incorporated into your program include:

Danger is used to indicate the presence of a hazard which WILL cause SEVERE

personal injury if the warning is ignored.

THIS SAFETY ALERT SYMBOL IDENTIFIES IMPORTANT SAFETY MESSAGES IN THIS MANUAL.

WHEN YOU SEE THIS SYMBOL , BE ALERT TO THE POSSIBILITY OF PERSONAL INJURY, AND

CAREFULLY READ THE MESSAGE THAT FOLLOWS.

A company’s safety program must involve everyone in the company, from top management to operators, since only as a group can any operational

problems be identified and resolved. It is everyone’s responsibility to implement and communicate the information and material contained in catalogs

and instruction manuals to all persons involved in machine operation. If a language barrier or insufficient education would prevent a person from

reading and understanding various literature available, it should be translated, read or interpreted to the person, with assurance that it is understood.

Never place your hands or any part of your body in this machine.

Never operate this machine without proper eye, face and body protection.

Never operate this machine unless you are fully trained, instructed, and you have read the instruction manual.

Never operate this machine if it is not working properly—stop operating and advise your supervisor immediately.

Never use a foot switch to operate this machine unless a point-of-operation guard or device is provided and

properly maintained.

Never operate this machine unless two-hand trip, two-hand control or presence sensing device is installed at the proper

safety distance. Consult your supervisor should you have any questions regarding the proper safety distance.

Never tamper with, rewire or bypass any control or component on this machine.

DANGER

“ ”

Safety Precautions

DANGER

FOR MAINTENANCE AND INSPECTION ALWAYS REFER TO THE OEM’s (ORIGINAL EQUIPMENT

MANUFACTURER’S) MAINTENANCE MANUAL OR OWNER’S MANUAL. If you do not have an owner’s

manual, please contact the original equipment manufacturer.

SECTION 1 — IN GENERAL

SSC-500 Hydraulic Press Solid-State Control

Rockford Systems, LLC

4Call: 1-800-922-7533

(Continued on next page.)

ANSI SAFETY STANDARDS FOR MACHINES

The most complete safety standards for machine tools are published

in the ANSI (American National Standards Institute) B11 series. The

following is a list of each ANSI B11 Standard available at the printing

of this publication.

B11.1 Mechanical Power Presses

B11.2 Hydraulic Presses

B11.3 Power Press Brakes

B11.4 Shears

B11.5 Iron Workers

B11.6 Lathes

B11.7 Cold Headers and Cold Formers

B11.8 Drilling, Milling and Boring

B11.9 Grinding Machines

B11.10 Sawing Machines

B11.11 Gear Cutting Machines

B11.12 Roll Forming and Roll Bending

B11.13 Automatic Screw/Bar and Chucking

B11.14 Coil Slitting Machines

B11.15 Pipe, Tube and Shape Bending

B11.16 Metal Powder Compacting Presses

B11.17 Horizontal Hydraulic Extrusion Presses

B11.18 Coil Processing Systems

B11.19 Performance Criteria for the Design, Construc-tion, Care

and Operation of Safeguards as Referenced in the Other

B11 Machine Tool Safety Standards

B11.20 Safety Requirements for Manufacturing Sys-tems/Cells

B11.21 Lasers

B11.22 CNC Turning Machines

B11.23 Machining Centers

B11/TR1 Ergonomic Considerations for the Design, Installation and

Use of Machine Tools

B11/TR2 Mist Control

B11/TR3 Hazard ID and Control

B11/TR4 Control Reliability

R15.06 Robotic Safeguarding

These standards can be purchased by contacting:

American National Standards Institute, Inc.

11 West 42nd Street

New York, New York 10036

Phone: (212) 642-4900

Fax: (212) 302-1286

www.ansi.org

Association of Manufacturing Technology (AMT)

7901 Westpark Drive

McLean, Virginia 22102

Phone: (703) 827-5211

Fax: (703) 893-1151

www.mfgtech.org

Safety References

OSHA’S ACT AND FEDERAL REGULATIONS

Since the enclosed equipment can never overcome a mechanical defi-

ciency, defect or malfunction in the machine itself, OSHA (Occupational

Safety and Health Administration) has established certain safety regula-

tions that the employers (users) must comply with so that the machines

used in their plants, factories or facilities are thoroughly inspected

and are in first-class operating condition before any of the enclosed

equipment is installed.

1. An Act – Public Law 91 - 596, 91st Congress, S. 2193,

December 29, 1970

Duties:

Sec. 5. (a) Each employer —

(1) shall furnish to each of his employees employ-

ment and a place of employment which are free from recog-

nized hazards that are causing or are likely to cause death or

serious physical harm to his employees;

(2) shall comply with occupational safety and health standards

promulgated under this Act.

(b) Each employee shall comply with occupational safety and

health standards and all rules, regulations, and orders issued

pursuant to this Act which are applicable to his own actions

and conduct.

2. OSHA’s Code of Federal Regulations, Subpart O, that an

employer (user) must comply with include:

Section 1910.211 Definitions

Section 1910.212 (a) General Requirements for all Machines

Section 1910.217 Mechanical Power Presses

Section 1910.219 (b)(1) Mechanical Power-Transmission Apparatus

(Flywheel and Gear Covers)

3. OSHA’s 29 Code of Federal Regulations, Subpart J 1910.147

The Control of Hazardous Energy (Lockout / Tagout)

4. OSHA’s Publications

“General Industry Safety and Health Regulations Part 1910,” Code

of Federal Regulations, Subpart O

“Concepts and Techniques of Machine Safeguarding,” OSHA 3067,

Revised 1992

These publications can be obtained by contacting:

Superintendent of Documents

US Government Printing Office

P.O. Box 371954

Pittsburgh, PA 15250-7954

Phone: (202) 512-1800

Fax: (202) 512-2250

www.gpo.gov

SECTION 1 — IN GENERAL

SSC-500 Hydraulic Press Solid-State Control

Rockford Systems, LLC

Call: 1-800-922-7533 5

(Continued on next page.)

WARRANTY

Rockford Systems, LLC warrants that this product will be free from defects in material and workmanship for a period of 12 months from the date of shipment

thereof. ROCKFORD SYSTEMS LLC’S OBLIGATION UNDER THIS WARRANTY IS EXPRESSLY AND EXCLUSIVELY LIMITED to repairing or replacing such products

which are returned to it within the warranty period with shipping charges prepaid and which will be disclosed as defective upon examination by Rockford

Systems, LLC This warranty will not apply to any product which will have been subject to misuse, negligence, accident, restriction and use not in accordance

with Rockford Systems, LLC’s instructions or which will have been altered or repaired by persons other than the authorized agent or employees of Rockford

Systems, LLC Rockford Systems, LLC’s warranties as to any component part is expressly limited to that of the manufacturer of the component part.

LIMITATION OF LIABILITY

Under no circumstances, including any claim of negligence, strict liability, or otherwise,

shall Rockford Systems, LLC be liable for any incidental or consequential damages, or

any loss or damage resulting from a defect in the product of Rockford Systems, LLC

Warranty, Disclaimer and Limitation of Liability

NATIONAL SAFETY COUNCIL SAFETY MANUALS AND DATA

SHEETS

Other good references for safety on machine tools are the National

Safety Council’s Safety Manuals and Data Sheets. These manuals and

data sheets are written by various committees including the Power

Press, Forging and Fabricating Executive Committee. Copies of the

following publications are available from their library:

Manuals

Power Press Safety Manual - 4th Edition

Safeguarding Concept Illustrations - 6th Edition

Forging Safety Manual

Data Sheets

Bench and Pedestal Grinding Wheel Operations 12304-0705

Boring Mills, Horizontal Metal 12304-0269

Boring Mills, Vertical 12304-0347

Coated Abrasives 12304-0452

Cold Shearing Billets and Bars in the Forging Industry

12304-0739

Degreasing (Liquid), Small Metal Parts 12304-0537

Dies, Setup and Removal of Forging Hammer 12304-0716

Drill Presses, Metalworking 12304-0335

Drills, Portable Reamer 12304-0497

Drop Hammers, Steam 12304-0720

Electrical Controls for Mechanical Power Presses 12304-0624

Forging Hammer Dies, Setup and Removal of 12304-0716

Forging Presses, Mechanical 12304-0728

Gear-Hobbing Machines 12304-0362

Handling Materials in the Forging Industry 12304-0551

Kick (Foot) Presses 12304-0363

Lathes, Engine 12304-0264

Milling Machines, Metalworking 12304-0364

Planers, Metal 12304-0383

Power Press (Mechanical) Point-of-Operation Safeguarding, Concepts of

12304-0710

Power Press Point-of-Operation Safeguarding: Two-Hand Control and

Two-Hand Tripping Devices 12304-0714

Power Press Point-of-Operation Safeguarding: Type A and B Movable Barrier

Devices 12304-0712

Power Press Point-of-Operation Safeguarding: Point-of-Operation Guards

12304-0715

Power Press Point-of-Operation Safeguarding:

Presence Sensing Devices 12304-0711

Power Press Point-of-Operation Safeguarding:

Pullbacks and Restraint Devices 12304-0713

Power Presses (Mechanical), Inspection and

Maintenance of 12304-0603

Power Presses (Mechanical), Removing Pieceparts

from Dies in 12304-0534

Power Press, Setting Up and Removing Dies 12304-0211

Press Brakes 12304-0419

Robots 12304-0717

Saws, Metal (Cold Working) 12304-0584

Shapers, Metal 12304-0216

Shears, Alligator 12304-0213

Shears, Squaring, Metal 12304-0328

Upsetters, 12304-0721

Copies of these manuals and data sheets can be obtained by contacting:

National Safety Council

1121 Spring Lake Drive

Itasca, IL 60143-3201

1-800-621-7619 ext. 2199

Fax: (630) 285-0797

www.nsc.org

OTHER SAFETY SOURCES

National Institute of Occupational Safety and Health (NIOSH)

4676 Columbia Parkway

Cincinnati, OH 45226

Phone: (513) 533-8236

Robotic Industries Association (RIA)

P.O. Box 3724

Ann Arbor, MI 48106

Phone: (734) 994-6088

www.robotics.org

For additional safety information and assistance in devising,

implementing or revising your safety program, please contact the

machine manufacturer, your state and local safety councils, insurance

carriers, national trade associations and your state’s occupational

safety and health administration.

DISCLAIMER

The foregoing Warranty is made in lieu of all other warranties, expressed or

implied, and of all other liabilities and obligations on the part of Rockford

Systems, LLC, including any liability for negligence, strict liability, or otherwise,

and any implied warranty of merchantability or fitness for a particular purpose

is expressly disclaimed.

SECTION 1 — IN GENERAL

SSC-500 Hydraulic Press Solid-State Control

Rockford Systems, LLC

6Call: 1-800-922-7533

(Continued on next page.)

Accompanying this equipment is an 8-1/2” x

11” operator safety precaution pamphlet, Part

No. KSC-000, for anyone operating the machine

where this equipment will be installed. This

precaution pamphlet is to be given to all oper-

ators, including setup people, maintenance

personnel and supervisors.

This pamphlet should also be attached to the

machine, readily accessible and visible to the

operator. (A hole in the corner of this precau-

tion pamphlet is provided for attaching pur-

poses.) Additional copies of this precaution

are available. Please call, e-mail, write, fax,

or use the order form found on a later page in

this manual.

When a language barrier or insufficient edu-

cation prevents a person from reading or

understanding the contents of this operator

safety precaution pamphlet, you should either

translate this information or have it read or

interpreted to the person. Make sure that the

person understands the information. To order

this pamphlet in Spanish, use Part No. KSC-

000S; in French, use Part No. KSC-000F.

This precaution pamphlet must be reviewed daily.

Operator Safety Precaution Pamphlet - (Attachment for machine operators)

Part No. KSC-000

Front

Back

SECTION 1 — IN GENERAL

SSC-500 Hydraulic Press Solid-State Control

Rockford Systems, LLC

Call: 1-800-922-7533 7

(Continued on next page.)

Danger Sign(s) to be Mounted on Machine

Never operate this machine unless the danger sign(s) is in place.

If any danger sign becomes destroyed or unreadable, the sign must be replaced immediately. Contact factory for replacement danger sign(s).

“Mechanical Power Press Safety” Booklet

A copy of Booklet No. MPPS (“Mechanical Power Press Safety”) is available upon request. This booklet is copied verbatim from the CFR (Code

of Federal Regulations) and contains all relevant sections of the OSHA Regulations concerning power presses with which an employer (user) must

comply. The enclosed equipment must be installed, used and maintained to meet these regulations. Specifically, any time a foot switch is used,

a suitable point-of-operation safeguard or device must be used to prevent bodily injury. In addition, every press must be provided with

a point-of-operation safeguard! Please review this booklet and the appropriate ANSI (American National Standards Institute) Safety Standard

before installing the enclosed equipment. If you are unfamiliar with these detailed safety regulations, which include regulations on safeguarding the

point of operation properly, you may want to attend our regularly scheduled machine safeguarding seminar. To obtain detailed information about

this training seminar, please call, fax, write, or check our web site. Our address, telephone, fax number, and web site address are on the front

cover of this manual.

Part No. KSC-054 Danger Sign - Standard

Part No. KSC-054S - Spanish

Part No. KSC-054F - French

Reverse Side

Part No. KSC-055 Danger Sign

(Foot) - Standard

Part No. KSC-055S - Spanish

Part No. KSC-055F - French

See page 6 for

details on this

pamphlet.

OPERATOR

SAFETY PRECAUTIONS

Handout for Anyone Operating This Machine

Before You Operate This Machine

You Must Read and Understand

These Safety Precautions

See Reverse Side for Other Safety Precautions.

OVER

Place Your Hands

or Any Part of 

Your Body in This 

Machine

Sign No. KSC-000

DANGER

OPERATOR

SAFETY PRECAUTIONS

Handout for Anyone Operating This Machine

Before You Operate This Machine

You Must Read and Understand

These Safety Precautions

See Reverse Side for Other Safety Precautions.

OVER

Place Your Hands

or Any Part of 

Your Body in This 

Machine

SIGN NO. KSC-000

Accompanying this equipment is a 5” x 6” polyethylene danger sign, Part No. KSC-054. This sign MUST BE PERMANENTLY

MOUNTED IN A PROMINENT LOCATION on the machine where this equipment is installed. This sign must be in a LOCATION

THAT IS EASILY VISIBLE to the operator, setup person, or other personnel who work on or around this machine. ALWAYS

mount this sign with screws or rivets when installing the enclosed equipment. If a foot switch is ordered, a 5” x 6”

polyethylene danger sign, Part No. KSC-055 is provided. This sign must also be mounted according to the above instructions.

Front Side

DO NOT REMOVE OR COVER THIS SIGN - SEE BACK FOR MOUNTING

Part No. KSC-054

Do not remove or cover this sign–see back for mounting instructions

Part No. KSC-054

You are exposed to moving

machine parts that can crush,

dismember and cause death.

DO NOT operate this machine with-

out safeguards in place.

This sign does not cover all dangers that

could happen while operating this machine.

CLOSING RAM AND DIE

NEVER place your hands or any

part of your body in this

machine.

FAILURE to obey will result in loss

of fingers or limbs, or

could cause death.

Front Side

SECTION 1 — IN GENERAL

SSC-500 Hydraulic Press Solid-State Control

Rockford Systems, LLC

8Call: 1-800-922-7533

(Continued on next page.)

Danger and Warning Labels Provided on Control Box

The illustrated danger and warning labels are affixed to all control boxes provided. All personnel operating or

working around the machine, where this control box is installed, must be required to read, understand and

adhere to all dangers and warnings. If any of these labels become destroyed or unreadable, labels MUST be

replaced. Contact factory immediately for replacement labels and do not operate the machine until the danger

and warning labels are all in place.

KSS - 027

Photo 1.1

Inside View of

SSC-500 Control Box

SECTION 1 — IN GENERAL

SSC-500 Hydraulic Press Solid-State Control

Rockford Systems, LLC

Call: 1-800-922-7533 9

FOR REPLACEMENT SIGNS

CALL, FAX, E-MAIL, OR FACTORY OR USE ORDER

FORM ON A LATER PAGE OF THIS MANUAL.

Rockford Systems, LLC

5795 Logistics Parkway

Rockford, Illinois 61109

Toll Free: 1-800-922-7533 (USA only)

Phone: (815) 874-7891

Fax: (815) 874-6144

Web Site: www.rockfordsystems.com

E-Mail: [email protected]

Photo 1.2

SSC-500 Control Box

SECTION 2 — INTRODUCTION

SSC-500 Hydraulic Press Solid-State Control

Rockford Systems, LLC

10 Call: 1-800-922-7533

(Continued on next page.)

General Description of Components in the System

A complete control package for hydraulic machines includes the following:

1. Literature folder (see page 14) containing installation manuals, “Operator Safety Precaution” Pamphlet, danger sign(s), electrical control

schematics, and our latest catalog

2. Control box - standard (custom or special includes motor controls and/or disconnect switch) with danger and warning signs

3. Palm button assembly (Includes two black palm buttons, two palm button guards, one red emergency-stop button, and mounting boxes. When

the “automatic” mode of operation is included, one yellow return/inch-up button with mounting box is furnished.) If multiple operator stations

are on a machine, more than one assembly is furnished.

4. Foot switch (optional) - If multiple operator stations are on a machine, more than one foot switch is furnished

5. Supervisory control station (Required when multiple operator stations are used on the machine; one station is required for each operator.)

6. Other required components and safeguarding that may be necessary for machine (See packing list for details.)

Individual packages may vary in contents. However, a packing list is always enclosed showing exactly what material was shipped on this order.

Please check the components actually received against this packing list immediately. In most cases, this control package system includes two-hand

control which can be used as a point-of-operation safeguarding device provided the palm buttons are mounted correctly and at the proper safety

distance (see formula on page 19 of this manual). If the optional foot switch is provided, a safeguard must always be used. Examples of safeguards

include barrier guards, presence sensing devices, pullbacks, restraints, gates, or two-hand control. The hands or any other part of the body of an

operator, maintenance person, setup person, etc., must never be put into the point-of-operation hazard for any reason, at any time.

These controls can neither cure nor overcome a malfunctioning machine. They cannot compensate for or prevent

a mechanical defect or failure of a machine part. These controls cannot prevent a repeat or unintended stroke

(cycle) resulting from a mechanical or hydraulic component malfunction, defect or failure of the machine itself.

Preliminary Steps Before Installation

Before proceeding with the installation of the enclosed equipment, you should undertake the following preliminary steps.

1. Read and make sure you understand this entire Installation Manual.

2. Refer to the front cover, other line drawings and photos, then make a rough sketch of your installation to plan the location of the enclosed

equipment on the machine.

3. This may be an opportunity to strip down the entire machine by removing all components, piping, wire,etc. Clean, paint and check the entire

electrical, hydraulic, and mechanical systems of the machine for proper adjustment and required replacement parts before proceeding with the

installation of the furnished equipment.

4. Please make sure the machine is in first-class condition. Before starting any installation, it is essential that the machine is thoroughly

inspected. Be sure that all mechanical components and all collateral equipment are in first-class operating condition. Your inspection should be

done according to the machine manufacturer’s installation and maintenance instruction manual. If you have any doubts or questions concerning

the condition of the machine, contact the machine manufacturer for assistance. Repair or replace all parts not operating properly before

proceeding.

Inspection and maintenance programs must be established and implemented to keep machines in first-class

condition. Programs must include thorough inspections of each machine on a weekly basis and records kept of

these inspections. Any part of the machine that is worn, damaged or is not operating properly must be replaced

immediately or repaired before the machine is used.

5. Verify that the machine is in first-class condition and operating properly; shut off all power to the machine. All trapped hydraulic pressure must be