Robertshaw RS4110 Manuel utilisateur

Thank you for purchasing a Robertshaw®thermostat. This manual will

describe how to install and test the Robertshaw single stage thermostats

RS4110, RS5110, RS6110, and two stage RS4220, RS5220, RS6220

thermostats. For complete operation instructions, refer to the Robertshaw

User Manual.

Use the model number to identify your thermostat.

These thermostats have three main parts:

A. The backplate – mounts to the wall and has wire connections.

B. The body – snaps to the backplate and contains the electronics and

programming buttons.

C. The cover – snaps to the top of the body and swings up to give access

to the programming buttons.

Recycling Thermostat

If this thermostat is replacing a thermostat that contains mercury in a sealed

tube, do not place your old thermostat in the garbage. Contact your local

waste management authority for instructions regarding proper disposal of the

thermostat. If you have any questions, call Robertshaw technical support at

1-800-445-8299.

RS4110

RS5110

RS6110

RS4220

RS5220

RS6220

R S X 1 1 0

4 = Non-Programmable

Value Series

5 = Programmable Value Series

with 5-2 Day Schedule

6= Programmable Value Series

with 7 Day Schedule and

Copy Feature

Application

0 = Standard Thermostat

Number of Cooling Stages

Number of Heating Stages

INSTALLATION MANUAL

RS4000 Series RS5000 Series RS6000 Series

352-00060-001 Rev. A

IMPORTANT SAFETY INFORMATION WARNING:

• Always turn off power at main fuse or circuit breaker panel before

installing, removing, cleaning, or servicing thermostat.

• Read all the information in this manual before installing this thermostat.

• This is a 24 VAC low-voltage thermostat. Do not install on voltages

higher than 30 VAC.

• All wiring must conform to local and national building and electrical

codes and ordinances.

• To take advantage of the Pop-Up Wizard, power should be applied when

the settings are ready to be entered. Fill in the chart in the Pop-Up

Wizard section before applying power.

• This is a dual powered thermostat that will operate on 24 VAC or batteries.

• Do not short (jumper) across terminals on the gas valve or at the

system control to test installation. This will damage the thermostat and

void the warranty.

• Do not connect ground to any terminal in this unit.

• This thermostat is configured with automatic compressor protection to

prevent damage because of short cycling or extended power outages.

Short cycle protection provides a delay between compressor cycles on

heat pumps.

Replacing Existing Thermostat

1. Turn off power to heating and cooling system.

2. Remove cover from old thermostat to expose wires.

3. Disconnect wires one at a time from existing terminals. Use enclosed

labels to mark existing wires. Refer to cross references in Table 1 if

existing wiring does not directly match the labels.

4. Remove existing thermostat base from wall.

Table 1

Old Terminal New Label Description

R, RH/R, V-VR or VR-R R/RH 24V AC Return

RC RC 24V AC Cooling Transformer

Y, Y1 or M Y1 1st Stage Cooling Circuit

F or G G Fan Control Relay

Y2 Y2 2nd Stage Cooling Circuit

W2 or W-U W2 2nd Stage Heating Control

C, X or B C 24V AC Transformer Common Side

W1 or W W1 1st Stage Heating Circuit

Installing the Robertshaw Thermostat Base

NOTE: For new installations, mount the thermostat on an inside wall, five feet

above the floor. Do not install behind a door, in a corner, near air vents,

in direct sunlight, or near any heat or steam generating fixtures.

Installation at these locations will affect thermostat operation.

1. Be certain power is off to the heating and cooling systems.

2. Remove the backplate by placing your finger through the wire opening.

Pull the backplate straight out from the body.

3. Place the backplate in position on the wall. Pull the wires through the

wire opening.

4. Hold the backplate level and mark the mounting holes on the wall.

5. Drill the marked holes using a 5 mm (3/16 in.) drill bit.

6. Tap in the wall anchors and secure the base to the wall with the

supplied screws.

NOTE: The thermostats are designed to also mount on a single gang

junction box.

Providing Power to the Thermostat

To take advantage of the Pop-Up Wizard, power should be applied when the

settings are ready to be entered. Fill in the chart in the Pop-Up Wizard

section before applying power.

These thermostats will run on either two AA batteries or 24 VAC. If the

common wire from the transformer is not available, the unit must be powered

by two AA batteries.

Thermostats with batteries and powered by 24 VAC will continue to function if

the 24 VAC fails.

Maintaining the Batteries

When the batteries are low, the thermostat will enter a low power mode. Low

battery mode has two levels.

• LEVEL 1: The low battery icon will be displayed.

• LEVEL 2: The low battery icon will flash indicating

that THE SYSTEM WILL NOT OPERATE.

Wiring Terminals

Mounting Holes

Wire Opening

RH/R

System Switch Selection

The body of the thermostat has two switches on the backside. They are

accessible by removing the backplate from the body. The installer should set

these to match the system.

If the thermostat is controlling a heat pump system, set the first switch to

Heat Pump. The second switch can be left as is.

If the thermostat is controlling a non-heat pump system, set the first switch to

Non-Heat Pump. The second switch must be set to match the system as Gas

or Electric.

If Non-Heat Pump and Gas are selected, the heating system will control the fan.

If Non-Heat Pump and Electric are selected, the thermostat will control the fan.

Connecting the Wires

1. The wire ends should be stripped back 8 mm (5/16 in.).

2. Use the Wiring Diagrams and secure the wires into the terminal strip.

If replacing another thermostat, the wires should have been labeled.

Match the labels to the terminals. Tighten the screws.

3. Pull lightly on each wire to ensure the connection is secure.

NOTE: Nightlight feature is only enabled when the RH/R and C terminals

are connected.

Non-Heat

Pump Gas

Electric

Heat

Pump

Heat Pump or Non-Heat Pump Gasor Electric

Terminal Function

One Stage Models RS4110, RS5110 and RS6110

TERMINAL EQUIPMENT TO

CONNECTDESCRIPTION

C24V AC

Common Connection

For input of 24V AC common side of transformer.

Connect to provide always-on backlight/nightlight.

RH/R 24V AC

Hot Connection For input of 24V AC hot side of transformer.

RC 24V AC

Hot Connection

When cooling transformer is used for input of 24V

AC hot side of transformer.

Jumper from RH to RC must be removed.

Y1*

First stage

compressor

connection

Energizes on a call for first stage of cooling.

Energizes on a call for first stage of heating when

configured as a HP.

W1* First stage

heat connection

Energizes on a call for first stage of heating when

configured as a Non-HP.

GIndoor fan

connection

Energizes with Y1 and Y2.

Energizes with W1 and W2 if the Gas/Elec switch is

set to electric.

Energizes when fan is switched to ON.

OEnergizes for heat pump cool reversing valve.

BEnergizes for heat pump heat reversing valve.

* This thermostat can be used as a heat-only or cool-only thermostat. Therefore, it is not

always necessary to use both W1 and Y1.

Two Stage Models RS4220, RS5220 and RS6220

TERMINAL EQUIPMENT TO

CONNECTDESCRIPTION

24V AC

Compressor Fault

Output

For input of fault signal from a compressor.

Second stage

cooling

connection.

Energizes on a call for second stage cooling (aux.).

W2 Second stage

heat connection Energizes on a call for second stage heating (aux.).

EEmergency Heat

Connection Energizes on a call for emergency heat.

Compressor

Contactor

Reversing

Valve

Fan

Relay

RH/R

Transformer

Hot

120 Vac

Remove jumper if

separate cooling

transformer is

present.

When used as

Heat Pump with Cool Active Reversing Valve With Battery

Make certain the HP switch isin the HP position.

24 Vac

Compressor

Fault Output

(24VAC)

Second

Stage Cool

Second

Stage Heat

Emer Heat

Not used

for RS4110,

RS5110 and

RS6110

Not used

for RS4110,

RS5110 and

RS6110

Compressor

Contactor

Reversing

Valve

Fan

Relay

RH/R

Transformer

Hot

120 Vac

Remove jumper if

separate cooling

transformer is

present.

When used as

Heat Pump with Heat Active Reversing Valve With Battery

Make certain the HP switch isin the HP position.

24 Vac

Compressor

Fault Output

(24VAC)

Second

Stage Cool

Second

Stage Heat

Emer Heat

Not used

for RS4110,

RS5110 and

RS6110

Not used

for RS4110,

RS5110 and

RS6110

Compressor

Contactor

Fan

Relay

RH/R

Heat

Transformer

Hot

120 Vac

Remove jumper if

separate cooling

transformer is

present.

When used as

Non-Heat Pump With Battery

Make certain the HP switch isin the Non-HP position.

24 Vac

Second

Stage Cool

Second

Stage Heat

First Stage

Heat

Hot

120 Vac

24 Vac

Cooling

Transformer

Cooling transformer isnot required

Not used

for RS4110,

RS5110 and

RS6110

Not used

for RS4110,

RS5110 and

RS6110

Wiring Diagrams

Compressor

Contactor

Fan

Relay

RH/R

Transformer

Hot

120 Vac

Remove jumper if

separate cooling

transformer is

present.

When used as

Non-Heat Pump With Battery Backup

Make certain the HP switch isin the Non-HP position.

24 Vac

Second

Stage Cool

Second

Stage Heat

First Stage

Heat

Not used

for RS4110,

RS5110 and

RS6110

Not used

for RS4110,

RS5110 and

RS6110

Compressor

Contactor

Reversing

Valve

Fan

Relay

RH/R

Transformer

Hot

120 Vac

Remove jumper if

separate cooling

transformer is

present.

When used as

Heat Pump with Cool Active Reversing Valve With Battery Backup

Make certain the HP switch isin the HP position.

24 Vac

Compressor

Fault Output

(24VAC)

Second

Stage Cool

Second

Stage Heat

Emer Heat

Not used

for RS4110,

RS5110 and

RS6110

Not used for

RS4110, RS5110

and RS6110

Compressor

Contactor

Reversing

Valve

Fan

Relay

RH/R

Transformer

Hot

120 Vac

Remove jumper if

separate cooling

transformer is

present.

When used as

Heat Pump with Heat Active Reversing Valve With Battery Backup

Make certain the HP switch isin the HP position.

24 Vac

Compressor

Fault Output

(24VAC)

Second

Stage Cool

Second

Stage Heat

Emer Heat

Not used

for RS4110,

RS5110 and

RS6110

Not used

for RS4110,

RS5110 and

RS6110

Wiring Diagrams

Applying Power

Before applying power, fill in the chart in the Pop-Up Wizard section of

this manual.

When 24V AC power or battery power is first applied to the thermostat, the

display will show the model number followed by the Pop-Up Wizard.

The thermostat will start normal operation following the Pop-Up Wizard.

Power is applied to the thermostat two ways:

1. Installing the batteries.

2. Not installing the batteries and connecting the thermostat body to a

backplate that has the C terminal connected and 24V AC present.

Note: A thermostat powered by 24V AC will use the batteries as backup

power if the 24V AC fails.

Installing Batteries

To remove the battery compartment

gently squeeze the ribbed edges on

both sides.

The battery compartment will pull down

from the thermostat body and will

detach. Install two AA batteries

following the polarity as shown inside

the compartment. Place compartment

back into the thermostat.

Connecting The Body

Attach the thermostat body to the backplate by holding it directly in front of

the backplate. The edges will match and the wiring connections will make

contact. Push the body in until it snaps in place.

Pop-Up Wizard

The Wizard routine will display factory default settings. Each setting will

display for ten seconds. Use the or buttons to change the setting.

Settings that are not changed will operate with the values that are displayed.

To fast forward through the Wizard, press Edit Schedule. The Wizard can be

exited by pressing Start/Stop Schedule. This will save the settings and place

the thermostat into operation.

Use this chart to write down the desired settings before applying power.

Displayed Details Default Change To

SCAL (choose F° or C°) °F _______

CLOC* (choose 12 or 24 hour) 12 _______

LITE (1 = always on, 0 = off) 0 _______

DIFF (differential, set between 0.5 to 3.0 F°

or 0.5 to 1.5 C°) 1F° _______

DIF2** (2nd stage differential,

added to first stage differential) 2F° _______

DLY2** (2nd stage delay, in minutes) 20 _______

DEDB (auto changeover deadband

in degrees) 3F° _______

HI (heat setting limit in degrees) 90°F _______

LO (cool setting limit in degrees) 45°F _______

VAC HEAT* (vacation heat setpoint in degrees) 62°F _______

VAC COOL* (vacation cool setpoint in degrees) 85°F _______

CHECK*** (check filter timer in hours) OFF _______

CYCL (compressor short cycle delay in minutes) 5 _______

CAL (calibration offset in degrees) 0 _______

* Not displayed on RS4000 and RS6000 models.

** Will not be displayed if the thermostat is single stage.

*** On RS4000 models, the Filter Check feature can be turned to OFF (0) or ON (1).

The number of hours cannot be set.

After the Wizard has configured the thermostat, the settings can be edited by

pressing and simultaneously. This will allow you to change settings.

Factory settings that have not been changed will use the default settings

for operation.

Additional Default Settings for RS4000

The RS4110 and RS4220 are single setpoint non-programmable (no clock)

thermostats and do not have a schedule.

Default settings that are not set in the Pop-Up Wizard are:

The fan setting is auto.

The setpoint is 70°F.

The keypad has no password protection.

Default EnergyStar™Settings for RS5000 and RS6000

The RS5110, RS5220, RS6110 and RS6220 are programmable thermostats

and are preprogrammed with a schedule that is recommended by

EnergyStar™. The schedule is designed to lower energy costs year-round.

Setting Time and Day for RS5110, RS5220, RS6110

and RS6220

To adjust the time and day settings press the SET TIME button. The hour will

flash. To change the settings:

1. Use the and buttons to change the flashing number.

2. Press the SET TIME button to move through hours, minutes and days

of week.

3. Make changes as needed. They will be saved automatically.

NOTE: THE THERMOSTAT WILL NOT CORRECT FOR

DAYLIGHT SAVING TIME.

Installation Test Utility

WARNING: The installation test procedures can damage the

heating/cooling equipment if used incorrectly. These procedures should only

be performed by trained HVAC personnel.

The following instructions may be used to test the heating/cooling system for

correct function.

To enter the test mode press and hold and for ten seconds.

While in test mode, only the , and Start/Stop Schedule buttons

are active.

Short Cycle protection is disabled when using the test utility.

Push the Start/Stop schedule button at any time to exit test mode.

In the test mode:

Press to force the fan on or off. The fan icon will rotate. If the selector

switches are set for NON-HP and GAS, the fan icon will not be displayed.

Pressing repeatedly will allow testing of the system modes. See

following tables. The display will show appropriate animated icons.

EnergyStar™ Temperature Settings

Winter (Heating) Summer (Cooling)

Morning (6:00 am) 70°F (21°C) 78°F (25°C)

Day (8:00 am) 62°F (17°C) 85°F (29°C)

Evening (6:00 pm) 70°F (21°C) 78°F (25°C)

Night (10:00 pm) 62°F (17°C) 82°F (28°C)

Autres manuels pour RS4110

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Robertshaw Thermostat

Robertshaw

Robertshaw 9420 Manuel utilisateur

Robertshaw

Robertshaw 9801I Manuel utilisateur

Robertshaw

Robertshaw 9701i Manuel utilisateur

Robertshaw

Robertshaw Smart Sense SMART 1000 Manuel utilisateur

Robertshaw

Robertshaw 9801I Manuel utilisateur

Robertshaw

Robertshaw RS9320T Manuel utilisateur

Robertshaw

Robertshaw 900 series Manuel

Robertshaw

Robertshaw 5300 Series Guide d'installation et d'utilisation

Robertshaw

Robertshaw RS4110 Manuel utilisateur

Robertshaw

Robertshaw 9420 Manuel utilisateur

Robertshaw

Robertshaw RS8210 Manuel utilisateur

Robertshaw

Robertshaw 300-224 Caractéristiques techniques

Robertshaw

Robertshaw RS9220 Manuel utilisateur

Robertshaw

Robertshaw RS3110 Series Manuel utilisateur

Robertshaw

Robertshaw 9620 Manuel utilisateur

Robertshaw

Robertshaw 9520 Manuel utilisateur

Robertshaw

Robertshaw 9725i2 Instructions d'installation et d'utilisation

Robertshaw

Robertshaw 8600 Manuel utilisateur

Robertshaw

Robertshaw 9505 Manuel utilisateur

Robertshaw

Robertshaw RS3210 Series Manuel utilisateur

Robertshaw

Robertshaw 9620 Manuel utilisateur

Robertshaw

Robertshaw 9901i Manuel utilisateur

Robertshaw

Robertshaw 9801i2 Manuel utilisateur

Robertshaw

Robertshaw 300-224 Caractéristiques techniques

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur