Robe ROBIN UV Strobe Manuel utilisateur
1
Version 1.3
2
Table of contents
1. Safety instructions ......................................................................................................... 3
2. Fixture exterior view ...................................................................................................... 5
3. Installation....................................................................................................................... 6
3.1 Connection to the mains ............................................................................................ 6
3.2 Installing the gel frame and barndoors....................................................................... 7
3.3 Rigging the xture and oor installation of the xture ................................................ 8
3.4 DMX-512 connection................................................................................................ 13
3.5 Ethernet connection ................................................................................................. 14
4. Control menu map........................................................................................................ 16
5. DMX chart...................................................................................................................... 18
6. Strobe and Special eects running ........................................................................... 20
6.1 Strobe ...................................................................................................................... 20
6.2 Special eects ......................................................................................................... 20
7. Control menu ............................................................................................................... 22
7.1 Tab " Address" .......................................................................................................... 23
7.2 Tab "Information" ...................................................................................................... 24
7.3 Tab "Personality" ...................................................................................................... 25
7.4 Tab "Manual Control"................................................................................................ 26
7.5 Tab "Stand-alone" .................................................................................................... 26
7.6 Tab "Service" ............................................................................................................ 27
8. RDM ............................................................................................................................... 28
9. Wireless DMX operation .............................................................................................. 28
10. Error and information messages .............................................................................. 29
11. Technical Specications............................................................................................ 30
12. Maintenance and cleaning......................................................................................... 32
12.1 Replacing fuse ....................................................................................................... 32
12.2 Disposing of the product ........................................................................................ 32
13.Extract from a test report of Brno University Of Technology - Light Laboratory..33
14. Appendix ..................................................................................................................... 34
14.1 Strobe and Special eects timing .......................................................................... 34
Robin UV Strobe
3
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE POWERING OR INSTALLING YOUR ROBIN UV Strobe !
Save it for future reference.
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to en-
sure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes
written in this manual.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this ma-
nual or any unauthorized modication to the device.
Please consider that damages caused by manual modications to the device are not subject to warranty.
The Robin UV Strobe was designed mainly for indoor use and it is intended for
professional applications only. It is not for household use.
1. Safety instructions
THIS LUMINAIRE IS DESIGNED WITH UV LEDS AND MUST BE INSTALLED IN COMPLIANCE WITH COM-
POTENT TECHNICAL DIRECTIONS TO PREVENT THE USER’S EYE AND BARE SKIN FROM EXPOSURE
TO HARMFUL UV RADIATION.
CE LUMINAIRE EST CONCU POUR ETRE UTILISE AVEC DES LED UV ET DOIT ETRE INSTALLE EN
STRICTE CONFORMITE AVEC LES INSTRUCTIONS AFIN D’EVITER QUE LES YEUX OU LA PEAU L’UTI-
LISATEUR NE SOIENT EXPOSES AUX EFFETS NEFASTES DES RAYONS UV.
CAUTION: Radiation exposure may cause blindness and cancer of skin!
Maximum exposure: 22 minutes at 7m(23ft) distance
29 minutes at 8m(26ft) distance
46 minutes at 10m(32.8ft) distance
103 minutes at 15m(49ft) distance
184 minutes at 20m(65.5ft) distance
Please read an extract from a test report at the end of the user manual.
Risk Group 3 LED product according to ČSN EN 62471.
Make sure that materials which are exposed to the UV radiation will not be damaged!
Make sure that the available voltage is not higher than stated on the rear panel of the xture.
This xture should be operated only from the type of power source indicated on the marking label. If you are
not sure of the type of power supplied, consult your authorized distributor or local power company.
WARNING! This unit does not contain an ON/OFF switch. Always disconnect power input cable to completely
remove power from unit when not in use or before cleaning or servicing the xture.
The power plug has to be accessible after installing the xture. Do not overload wall outlets and extension cords
4
as this can result in re or electric shock.
Do not allow anything to rest on the power cord. Do not locate this xture where the cord may be damaged by
persons walking on it.
Make sure that the power cord is never crimped or damaged by sharp edges. Check the xture and the power
cord from time to time.
Refer servicing to qualied service personnel.
Do not look at the xture´s LEDs during operation. The light beam may damage your eyes.
This xture falls under protection class I. Therefore this xture has to be connected to
a mains socket outlet with a protective earthing connection.
Do not connect this xture to a dimmer pack.
To guard against epileptic seizure:
Do not operate the xture near stairways. Provide advance notice that strobe lighting
is in use. Avoid extended periods of continuous ashing, particularly at frequencies of
10 to 20 ashes per second
If the xture has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched o until
it has reached room temperature.
When choosing the installation spot, please make sure that the xture is not exposed to extreme heat, moisture
or dust.
Air vents and slots in the xture are provided for ventilation, to ensure reliable operation of the device and to
protect it from overheating.The openings should never be covered with cloth or other materials, and never
must be blocked.
This xture should not be placed in a built-in installation unless proper ventilation is provided.
Never place lters or other materials over the front glass cover.
Only operate the xture after having checked that the housing is rmly closed and all screws are tightly fastened.
To avoid damage of the internal optical system of the xture, never let the sunlight (or other
light source) lights directly to the lens array, even when the xture is not working !
Keep ammable materials well away from the xture.
Provide a minimum clearance of 0.3 meters around air vents
Always use a secondary safety cable when rigging this xture.
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the xture.
The xture becomes very hot during operation. Allow the xture to cool approximately 20 minutes prior to ma-
nipulate with it.
Operate the xture only after having familiarized with its functions. Do not permit operation by persons not
qualied for operating the xture. Most damages are the result of unprofessional operation!
Please use the original packaging if the xture is to be transported.
Please consider that unauthorized modications on the xture are forbidden due to safety reasons!
If this device will be operated in any way dierent to the one described in this manual, the product may suer
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like
short-circuit, burns, electric shock, crash etc.
5
2. Fixture exterior view
4- Antenna
5- DMX IN
6 - DMX OUT
7 - Control buttons
8 - QVGA touch screen
9 - Fuse holder
10 - RJ 45 Input
11 - Power In
12 - Safety screw
13 - Locking mechanism
14 - Safety lock
15 - Screen cover
1- Glass cover and lens array
2 - U-holder
3- Tilt lock
The ENTER/DISPLAY ON button also serves for switching the display on when the xture is disconnected
from mains.
6
3. Installation
Fixtures must be installed by a qualied electrician in accordance with all
national and local electrical and construction codes and regulations.
3.1 Connection to the mains
For protection from electric shock, the xture must be earthed!
The Robin UV Strobe is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz
AC power source from 100-240 Volts.
Connect the xture to the mains by means of the enclosed power cord
If you need to install other plug on the power cord, note that the cores in the power cord are coloured according
to the following table. The earth has to be connected!
If you have any doubts about proper installation, consult a qualied electrician.
Core (EU) Core (US) Connection Plug Terminal Marking
Brown Black Live L
Light blue White Neutral N
Yellow/Green Green Earth
Do not overload the supply line and the connecting leads.
Wiring and connection work must be carried out by qualied sta!
7
3.2 Installing the gel frame and barndoors
Disconnect the xture from mains before the accessory installation.
Never operate the xture with barndoors closed.
1. Put the frame adaptor (1) on the xture and
secure it with four screws (2).
2. Insert the gel frame (4) into slots (3) of
the frame adaptor (1). Use the slots closer to
the glass cover of the xture.
3. Insert the barndoors (5) into second slots (3) of
the frame adaptor (1).
4. Secure inserted barndoors and (or) the gel
frame by means of the two locks (6).
Lift up a little the lock (6) to release it from
the projection (7) and move it to the position
as shown on the picture B until the projection (8)
snaps into lock (6).
Do not operate the xture with unsecured gel
frame or barndoors!
8
3.3 Rigging the xture and oor installation of the xture
A structure intended for installation of the xture (s) must safely hold weight of the xture(s) placed on it. The
structure has to be certicated to the purpose.
The xture (xtures) must be installed in accordance with national and local electrical and construction codes
and regulation..
For overhead installation, the xture(s) must be always secured with a safety wire
that can bear at least 10 times the weight of the xture(s).
When rigging, derigging or servicing the xture staying in the area below the installation place, on bridges,
under high working places and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by an
expert before taking into operation for the rst time and after changes before taking into operation another time.
The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled
person once a year.
Allow the xture to cool for ten minutes before handling.
The xture should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating working
load limits, installation material being used, and periodic safety inspection of all installation material and the
projector. If you lack these qualications, do not attempt the installation yourself, but use a help of professional
companies.
CAUTION: Fixtures may cause severe injuries when crashing down! If you have doubts concerning the safety
of a possible installation, do not install the xture!
The xture has to be installed out of the reach of public.
The xture must never be xed swinging freely in the room.
When installing the device, make sure there is no highly inammable
material (decoration articles, etc.) in a distance of min. 0.5 m.
CAUTION!
Use an appropriate clamp to rig the xture on the truss.
Follow the instructions mentioned at the bottom of the xture base.
Make sure that the device is xed properly! Ensure that the
structure (truss) to which you are attaching the xture is secure.
The xture can be placed directly on the stage oor or rigged to the truss. The xture can be rigged to the truss
via Omega holder and one clamp (two holes with 140mm spacing serve for this method of mounting) or using
stacker which allows 2-6 xtures connected in the top-to-bottom method.
For oor installation use a oor stand if two or more xtures are to be stacked
.
9
Single xture installation via the omega holder
1. Bolt the clamp (1) to the omega holder (2) with M12 bolt and lock nut through the hole in the holder.
2. Fasten the omega holder to the U-holder (4) of the xture by inserting both quick-lock fasteners (3) into
holes in the U-holder and tighten fully clockwise.
3. Clamp the xture on a truss (12) and tighten the rigging clamp (1).
4. For securing the xture to the truss, install a safety wire that can hold at least 10 times the weight
of the xture. Use only a safety wire with a snap hook with screw lock gate. Pull the safety
wire (11) through the U-holder (4) and around the truss (12) as shown on the picture below.
5. The tilt lock (7) allows to adjust the xture to desired position. In case, that the tilt lock cannot
be loosened (tightened) due to the housing of the xture, pull this tilt lock in a direction from the xture,
turn it to desired position, release it and continue in loosening (tightening) this tilt lock (principle of
a "ratcheting socket wrench").
If two and more xtures are to be connected in a top-to-bottom method, a stacker with two safety wires
has to be used - see article below.
Multiply xtures rigging
Maximum 6 xtures can be connected in the top-to-bottom method
Always use a stacker for a hanging multiply xtures installation . The position of the U-holder allows to tilt the
whole "stack" of xtures.
To change the position of the U-holder
1. In order to release the U-holder (4), press and hold the front part (1) of the pin (2) and pull it out from
the stacker. Use the same way to remove the pin (2) on the opposite side of the U-holder.
2. Move the U-holder to desired position.
3. Press and hold the top part (1) of the pin (2) and push it throw the U-holder into the hole in the stacker.
Secure the second side of the U-holder (4) by inserting the pin (2) into the stacker.
Check, that both sides of the U-holder are securely fastened.
Table of tilt angles for dierent loads of the stacker
Hole position 1 2 3 4 5 6 7 8 9
2 xtures -22 -10° 0° 10° 20° 30° 37° 45° -
4 xtures -10° -5° 0° 8° 15° 20° 25° 30° 35°
6 xtures -7.5° -3° 0° 5° 10° 15° 20° 22° 26°
.
10
To install multiple xtures in a top-to-bottom method
1. Rig the stacker to the truss (4) by means of two omega holders (2) on the U-holder (5) and two clamps (1)
and secure it with two safety wires (15). Use only safety wires with snap hook with screw lock gate.
The snap hooks have to go throw holes in the stacker.
2. Check if the locking mechanism of the rst xture is in an "unlock position" - the lever (18) is in the bottom
position and the red mark (16) is visible.
3. Connect the rst xture with the stacker in a way that feet (8) of the stacker will be
inserted into top openings (14) of the rst xture and move the rst xture in a direction as show
red arrows on the picture below until you feel a stop.
4. Secure the rst xture with the stacker by means of its locking mechanism: move both levers (18)
to the top position until the green mark (17) is visible and move the plastic levers (19) into position under
locking levers (18) until they snap. Now levers (18) cannot be moved to unlock position.
5. Make the secondary securing of the installed xture. Loosen both tilt locks (9) and move the U-holder (13)
to the horizontal position. Loosen the nuts (12) and move the segments (11) towards the stacker nuts (7).
Loosen the nuts (7) and fasten the segments (11) under them. Tighten the nuts (7) and the tilt locks (9).
Always check that locking mechanisms are locked before connecting next xture!
6. Check if the locking mechanism of the second xture is in the "unlock position" - the lever (18) is in
the bottom position and the red mark (16) is visible.
7. Connect the second xture with the rst one in a way that feet (8) of the rst xture will be
inserted into top openings (14) of the second xture and move the second xture in a direction as show
red arrows on the picture above until you feel a stop.
8. Secure the second xture with the rst one by means of its locking mechanism: move both levers (18)
to the top position until the green mark (17) is visible and move the plastic levers (19) into position under
locking levers (18) until they snap. Now levers (18) cannot be moved to unlock position.
9. Make the secondary securing of this xture. Loosen both tilt locks (9) and move the U-holder (13)
to the horizontal position. Loosen the nuts (12) and move the segments (11) towards the nuts (10).
Loosen the nuts (10) and fasten the parts (11) under them. Tighten the nuts (10) and the tilt locks (9).
10. Repeat steps 6-9 for the next xture. In this way, up to six xtures can be connected each other.
11. Check, that all nuts (7), (10) and tilt locks (9) are fully tightened.
Table des matières
Autres manuels Robe Matériel de DJ
Robe
Robe ANOLiS Eminere Remote UV 2 Manuel utilisateur
Robe
Robe Robin Tarrantula TW Manuel utilisateur
Robe
Robe Spot 575 XT Manuel utilisateur
Robe
Robe ROBIN BMFL LightMaster Side Manuel utilisateur
Robe
Robe CitySource 96 WDMX Manuel utilisateur
Robe
Robe ROBIN iParfect 150 RGBA Manuel utilisateur
Robe
Robe Anolis Calumma S MC Manuel utilisateur
Robe
Robe Anolis Calumma Remote M MC Manuel utilisateur
Robe
Robe picklePATT ES Manuel utilisateur
Robe
Robe Painte Manuel utilisateur
Robe
Robe StageQube 324 Manuel utilisateur
Robe
Robe pixelPATT Manuel utilisateur
Robe
Robe Spot 575 XT Manuel utilisateur
Robe
Robe Robin CycBar 15 Manuel utilisateur
Robe
Robe ROBIN SPIKIE Manuel utilisateur
Robe
Robe ROBIN iBeam 250 Manuel utilisateur
Robe
Robe Robin 1200 Manuel utilisateur
Robe
Robe ColorSpot 575E AT Manuel utilisateur
Robe
Robe ANOLIS Side Eminere 2 Wireles DMX Manuel utilisateur
Robe
Robe Anolis Calumma XL MC Manuel utilisateur
Manuels Matériel de DJ populaires d'autres marques
thomann
thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur
Eagletone
Eagletone 6 Eyes Flower Manuel utilisateur
EuroLite
EuroLite FLD-1508 Manuel utilisateur
Technical Pro
Technical Pro LG8xSEA Manuel utilisateur
JB Systems
JB Systems Lounge Laser DMX Manuel utilisateur
Lightmaxx
Lightmaxx Vega Halo 90 Manuel utilisateur
Elation
Elation FUZE WASH Z350 Manuel utilisateur
Maverick
Maverick MK3 WASH Manuel utilisateur
Infinity
Infinity TF-260C7 Fresnel Manuel utilisateur
Chauvet
Chauvet EVE E-50Z Manuel utilisateur
Eliminator Lighting
Eliminator Lighting E 138 Manuel utilisateur
EuroLite
EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur