Riverlea Rustics NEBRASKA Manuel utilisateur
NEBRASKA
ASSEMBLY INSTRUCTIONS
BASE SIZE: 3.600m x 2.490m
• Baery Drill
• Riveter
• Hammer
• Tape Measure
• Ladder
• Skillsaw
• Level
• Screwdriver - Flat
• 3/8 Hex Drive bit
• 8mm Hex Drive bit
• Drill Bit 3.2mm
• Socket Set
• Read all instrucons carefully.
• Idenfy all parts and check quanes against checklist.
• Do not aempt to build your shed in high winds.
• Beware of sharp edges.
• Protect your eyes and ears.
• Use electric tools with care. Use a Safety Trip Switch.
• It is easier and quicker if this shed is erected by two people.
• Your shed must be level. Achieve this by either levelling the
ground or by using blocks.
Tools Required:
Select your site:
Safety:
Before you start:
PG 1
NEBRASKA
Descripon Size Qty
PACK ONE - SHED
Standard Door 895 x 1780 1
Std Wall Panels 1200 x 1877 5
Front Wall Panel 300 x 1877 1
End Wall Panels (L/H) 1200 x 2389 2
End Wall Panels (R/H) 1200 x 2389 2
Door Lintel 110 x 900 1
Cedar Corner Clashings 85 x 17 x 1902 4
30 x 17 Std Cedarbead 30 x 17 x 1877 3
15 x 17 Std Cedarbead 15 x 17 x 1877 2
30 x 17 Gable Cedarbead 30 x 17 x 2389 2
Silicone Tube 300g 2
Roof Truss 535 x 2490 2
Barge Flashings 85 x 40 x 2960 2
Temporary Door Stop 45 x 45 x 900 1
Roof Sheets 845 x 1450 10
Ridge Flashing 175 x 2010 2
15mm Packer 15 x 45 x 1740 1
Hardware Pack
Tek Screws 14G x 75mm, CL4 50
Framing Nails 75 x 3.15mm 80
Bead Nails 50 x 2.5mm 60
Galv Clouts 30 x 2.5mm 50
Colour Rivets 3.2 x 8.2mm 50
Roong Screws and Washers 50mm 30
Padbolt and Keeper 1
Padbolt Screws 32 x 8g 6
Instrucons 1
Oponal
Building Paper (Roof + 20 clouts) 1370 x 7500 1
Clear Roof Panel (Panel replaces roof sheet) Qty
PACK TWO - STIFFENERS (& FLOOR if required)
Purlins (Top) 100 x 25 x 3740 2
Purlins (Boom) 50 x 25 x 3740 2
Spoung 3735mm 2
Seners 45 x 45 x 3600 2
Floor Joists 70 x 45 x 3590 5
Floor Boards 150 x 19 x 2480 24
Floor Nails 50 x 2.5mm 240
Packed by: Date: / /
NEBRASKA PARTS LIST
PG 2
PG 3
Step 1: Establish size of shed and excavate sucient area. Re-
member to allow for rear roof overhang up to 150mm, and
120mm on each end.
Step 2: Ensure that the base substrate is compacted rmly.
We suggest that the slab should be 80mm thick in the middle
and 100mm thick around the edges.
Step 3: Lay boxing to the required size, the raised slab
size should be 3585 x 2475mm and at least 30mm
above the ground line.
Step 4: Lay plasc sheeng if required. Plasc sheeng under slab
will prevent moisture coming through from underneath.
Step 5: Pour concrete and screed ush
Building a Raised Concrete Base
100mm
80mm
100mm
NEBRASKA CONCRETE FLOOR OPTION
PG 4
NEBRASKA FLOOR OPTION
Step 1: Lay out oor joists, spacing them evenly
as shown. Using 50mm ooring nails, nail a oor
board on each end, ensuring ends are ush with
joists. Make sure oor is level and joists are sup-
ported at 1240mm centres.
Step 2: Lay out remaining oor boards. Measure
diagonals to ensure measurements are equal (I.e.
oor is square). Rip down last oor board to suit
gap, and nail o oor with 50mm ooring nails
(10 nails per board).
Step 3: Unpack panels and idenfy wall panels
and door posions as per the wall plan located
on page 5.
Select two panels that go either side of a corner
(gable and standard panel) and stand together.
Example: R (standard) and LG (Gable)
Located on the boom plate of each wall.
PG 5
NEBRASKA WALL PLAN
NEBRASKA
WALL PLAN
1200RG
1200LG
1200 L
300
1200 R
1200RG
1200LG
1200 R
1200 C
1200 L
15 x 17mm Std Cedar bead
30 x 17mm Std Cedar bead
30 x 17mm Gable Cedar bead
Corner Clashing
45 x 20mm Packer
Tek Screws (To secure Walls to Floor)
Truss Locaon
Please note: The walls are not screwed down to the oor unl all the walls
are erected, the roof is in place and the door is about to be installed.
The Boom Plate of each wall will be labelled L, R, C, LG or RG based on
the posion it goes in the wall plan.
Step 4: Screw wall panels together using 75mm tek
screws (3 per low connecon, 4 per high connecon),
ensuring gable walls are inside the standard walls as
per the wall plan on the previous page.
Step 5: Silicone edge of weatherboards on the stand-
ing panel, and lying your next wall down silicone the
connecng edges weatherboards. Nail the bead to the
laid down panel. ( 4 bead nails per standard bead, 5
per gable bead)
Make sure bead is properly sealed to avoid leaks.
Note: On standard panels only, top of bead is bevelled
to allow for slope of roof.
Step 6: Silicone and nail remaining beads on each panel. Screw panels together us-
ing 3 tek screws per join and 4 on the longer joins on gable panels as menoned
above.
PG 6
NEBRASKA WALL INSTALLATION
PG 7
NEBRASKA DOOR LINTEL
Step 8: Using 75mm framing nails, nail both top
plate seners into standard wall panels studs, as
shown using 2 nails per each end stud, and 1 nail
for each remaining stud. Ensure ends are evenly
spaced before nailing.
Step 9: Using 30mm clouts nail top cedar boards
to seners (2-3 nails per board). Predrill holes to
stop boards from spling.
NEBRASKA STIFFENERS
Step 7: Using the 15mm Packer screw the door
lintel into place, using 2 x 75mm tek screws at
each end. Screwing though the stud into the
lintel.
Tip: Using the screw to predrill a hole before
aempng to screw into the lintel will make this
easier.
Above Lintel from the outside, below Lintel from
the inside.
PG 8
NEBRASKA CORNER CLASHINGS
NEBRASKA ROOF
Step 11: Posion roof trusses over the join of
the panels on the front and back walls, as
shown in the wall plan. Using 75mm framing
nails, nail the truss to the seners. Predrill the
truss as to avoid spling the mber.
Refer to Wall Plan on page 5 for correct truss locaon.
Step 12: Posion purlins on roof. (Top Purlins
100mm, boom purlins 50mm) Top purlins
should be together and boom purlins should
be against the Seners. Using 75mm framing
nails, predrill then nail purlins into top of gable
end panels and truss (2 nails per join).
Check that overhangs are even all around.
Condensaon can form on the under side of shed roof. If
building paper is required, t now. Nailing to the purlins with
the clouts provided.
Please note: The image above has one truss, this
model requires two.
Please note: The image above has one truss, this
model requires two trusses.
Step 10: Ensuring the clashing is ush at the top.
Silicone and nail corner clashings on all corners as
shown using 4 x bead nails per clashing.
Silicone both edges where the clashing meets the
weatherboards to ensure this doesn't leak.
PG 9
NEBRASKA ROOF
Step 13: Ensure shed is square, by measuring
diagonals at top corner of wall panels.
Step 14: Posion rst full sheet with rib ush with
end of purlins and top of sheet ush with the top
of the purlin.
Tack top of the sheet into the top purlin using a
30mm clout through the pan. Using a 35mm
Roong Screw with Washer, screw through the
rst full rib into the boom purlin to a depth of
approximately 10mm.
Tip: Predrilling with a 3mm drill bit may make this easier.
First full Rib
Pan
Step 15: Lay out remaining full roof sheets, with
sucient overlap that the last lip lines up with
the opposite ends purlins.
This may require overlapping mulple ribs.
Rivet these sheets together, 3 rivets per join, to
make 1 large roof panel as shown in photo.
Rivet top, middle and boom.
Tack remaining top corner and screw the boom
corner ensuring edge of sheet is ush with end of
purlins and height is correct.
Ensure purlins are straight, Nail through every
fourth pan using 30mm clouts into the top purlin,
using 35mm roong screws with washers screw
through every fourth rib into the boom purlin.
Tip: If you have string or a long piece of mber use it as a
guide to screw on a straight line.
Table des matières
Autres manuels Riverlea Entreposage extérieur
Riverlea
Riverlea Duratuf SS1510 Manuel utilisateur
Riverlea
Riverlea Duratuf KIWI KS2 Manuel utilisateur
Riverlea
Riverlea Duratuf Garrison Sheds PL64 Manuel utilisateur
Riverlea
Riverlea SmartStore SM2015 Manuel utilisateur
Riverlea
Riverlea SmartStore SM2515 Manuel utilisateur
Riverlea
Riverlea SmartStore SM1520 Manuel utilisateur
Riverlea
Riverlea DURATUF Sentry SL2015 Manuel utilisateur
Riverlea
Riverlea SmartStore SM2007 Manuel utilisateur
Riverlea
Riverlea SmartStore SM2525 Manuel utilisateur
Riverlea
Riverlea Duratuf KIWI SHEDS MK4C Manuel utilisateur
Riverlea
Riverlea Duratuf KIWI SHEDS MK3A Manuel utilisateur
Riverlea
Riverlea Duratuf Guardian SHED SGS73 Manuel utilisateur
Riverlea
Riverlea Duratuf Guardian Sheds GG101 Manuel utilisateur
Riverlea
Riverlea SmartStore SM1515 Manuel utilisateur
Riverlea
Riverlea Duratuf Guardian SHEDS GS63 Manuel utilisateur
Riverlea
Riverlea SmartStore SM3020 Manuel utilisateur
Riverlea
Riverlea Duratuf SENTRY SHEDS SG2020 Manuel utilisateur
Riverlea
Riverlea Smart Store SM2010 Manuel utilisateur
Riverlea
Riverlea Duratuf KIWI SHEDS MK4A Manuel utilisateur
Riverlea
Riverlea Duratuf Garrison Sheds PS62 Manuel utilisateur
Manuels Entreposage extérieur populaires d'autres marques
Lifetime
Lifetime 6418 Manuel utilisateur
rollaway container
rollaway container ARPCA24 Manuel utilisateur
Duratuf
Duratuf Havelock Manuel utilisateur
X-METAL
X-METAL 4065 Manuel utilisateur
Outdoor Life Products
Outdoor Life Products FP2030 F Manuel utilisateur
Royalcraft
Royalcraft Faro 295L Storage Box Manuel utilisateur
