RITE-HITE Eclipse 620G Manuel utilisateur

Eclipse®Dock Shelter

(620G, 620NH)

Installation/Service/Owner's Manual

Document Name: 620G0001

Illustration Name: 620G0002

Manual Part #: 39500129

Model #: 620G, 620NH

Publication: AMEN00141 2019-11-22

NOTICE TO USER . . . . . . . . . . . . . . . . . . .2

SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . . .3

INSTALLATION

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Preparation. . . . . . . . . . . . . . . . . . . . . . . . . 5

Mounting Methods . . . . . . . . . . . . . . . . . . . 5

Side Frames . . . . . . . . . . . . . . . . . . . . . . . . 6

Canopy Header . . . . . . . . . . . . . . . . . . . . . 8

Side Curtains . . . . . . . . . . . . . . . . . . . . . . 12

Weighted Seal, Wear Panel . . . . . . . . . . . 13

Bumpers . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Collapsible Style Draft Pad. . . . . . . . . . . . 17

MAINTENANCE . . . . . . . . . . . . . . . . . . . .19

PARTS

Exploded View – 620G. . . . . . . . . . . . . . . 20

Exploded View – 620NH. . . . . . . . . . . . . . 22

WARRANTY . . . . . . . . . . . . . . . . . . . . . . .24

Eclipse®Dock Shelter (620G, 620NH) Installation/Service/Owner's Manual Rite‑Hite®

2Publication: AMEN00141 2019-11-22

NOTICE TO USER

Thank you for purchasing a Rite‑Hite product.

The Eclipse®620G and 620NH Dock Shelters provide a

durable, e󰀨ective environmental seal between the trailer

and building.

Instructions apply to both 620G and 620NH unless

otherwise noted.

The English version of this manual shall prevail over any

error in, or conicting interpretation of, any translations.

Rite‑Hite reserves the right to substitute and/or modify

parts and drawings. If separate prints are included with

the unit, they supersede the manual.

For best results, have this product serviced by an

authorized Rite‑Hite representative.

A Planned Maintenance Program (P.M.P.), customized to

your specic operation is available and recommended.

For a P.M.P., contact your local Rite‑Hite representative

or Rite‑Hite technical support at (U.S.) 1‑888‑456‑3625,

(S.A.) +55 21 99616 4421.

The Rite‑Hite products in this manual are covered by one or more of the

following U.S. patents: 6014844, 6044597, 6205721, 6233885, 7146673,

7185463, 7246467, 7287353, 7584517, 7695048, 7757442, 7877831,

7882663, 8042307, 8141305, 8156995, 8307588, 8327587, 8353136,

8458960, 8495838, 8540007, 8752335, 8800086, 8839842, 8887447,

8915029, 8943630, 8991467, 9003724, 9003725, 9010039, 9079713,

9162832, 9170044, 9187271, 9193543 9534372, 9534373, 9551181,

9592972, 9624049, 9751703, 9797127, 9797128 and may be covered

by additional pending U.S. and foreign patent applications.

Manufactured by Rite‑Hite Environmental Enclosure Corporation.

Rite‑Hite®Installation/Service/Owner's Manual Eclipse®Dock Shelter (620G, 620NH)

Publication: AMEN00141 2019-11-22 3

SAFETY

Safety Identifications

DANGER

Indicates a hazardous situation which, if not

avoided, will result in death or serious injury.

WARNING

Indicates a hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION

Indicates a hazardous situation which, if not

avoided, could result in minor or moderate injury.

NOTICE

Indicates a situation which can cause damage to the

equipment, personal property and/or the environment,

or cause the equipment to operate improperly.

NOTE:A note is used to inform you of important

installation, operation, or maintenance information.

Lockout Procedure

Barricade work area and post safety warnings.

Power supply and control must:

• Be disconnected or locked in OFF position

using a lockout device approved by local

codes.

• Have signage that;

−Clearly states repairs are being made.

− Identies person responsible for lockout condition.

NOTE:Only this person should be able to remove

warnings and lockout device.

−Withstands environmental conditions (weather,

wet, and damp, etc.) and remains readable.

General

WARNING

To prevent unauthorized use, barricade the work

area at dock and ground level while service work

is being performed.

190820

Eclipse®Dock Shelter (620G, 620NH) Installation/Service/Owner's Manual Rite‑Hite®

4Publication: AMEN00141 2019-11-22

INSTALLATION

Overview

1. Unpack and inspect unit.

2. Install side frames and bracket anchors.

3. Install side arms, front bar and canopy top.

4. Install side curtains and pocket straps.

5. Install gutter, roller seal, and wear panels.

6. Install draft pads.

Instructions assume that the installer is outside the building facing the loading dock.

Figure 1

Rite‑Hite®Installation/Service/Owner's Manual Eclipse®Dock Shelter (620G, 620NH)

Publication: AMEN00141 2019-11-22 5

INSTALLATION

Preparation

Verify all components were received. Notify your Rite‑Hite

Representative if parts are missing or damaged.

Mounting Methods

NOTE:Any additional fasteners, backer plates and

materials for additional structure are supplied by others.

Concrete Block or Brick Wall

Through bolt fastening is required.

• Bore a hole through the building wall.

• Use a 3/8in [9mm] diameter threaded rod with

a washer, nut, and jam nut on each end.

• Install a backer plate inside the building wall when

the wall will not support the bolt.

Concrete Tilt-Up Walls (Precast)

Use 3/8in [9mm] lag bolts with expansion shields,

3/8in [9mm] 1 piece anchor bolts with expansion collar, or

equivalent fastener.

If building wall is too thin to e󰀨ectively hold the lag bolt or

anchor bolt, through bolt method of attachment is required.

NOTE:To determine anchor length, use anchor

manufacturer’s recommendation for minimum anchor

embedment.

Metal Sided Building

Through bolt fastening is required.

• Use a 3/8in [9mm] diameter bolt with a washer and

lock nut to fasten the unit to the structural member of

the building or to the backer plates. If necessary, use a

3/8in [9mm] diameter threaded rod with a washer and

lock nut on each end.

• Install a backer plate that is fastened directly to

structural member when it is not possible to fasten

directly to structural building members.

NOTE:See "Figure 2" for recommendations.

Uninsulated Wall Building

Building Structural Member

Filler Boards*

Min. 3/8in Fasteners*

Corrugated

Metal Siding

Head Frame

2x6 or Structural Steel Channel Backer

Angle Bracket*

Insulated Wall Building

Building Structural Member

Angle Bracket*

2x6 or Structural Steel Channel Backer*

Insulation

Filler Boards*

Head Frame

Pipe Spacers*

Corrugated

Metal Siding

Min. 3/8in Fasteners*

*Supplied by others.

Figure 2

Eclipse®Dock Shelter (620G, 620NH) Installation/Service/Owner's Manual Rite‑Hite®

6Publication: AMEN00141 2019-11-22

INSTALLATION

Side Frames

1. Before mounting side frames, install canopy mounting

brackets (A) to top of side frames (B).

• Position bracket so notches at top of bracket are

ush with the top of the wood, side pad backer (C).

• Secure in place with 6 hex head wood screws (J)

provided.

NOTE:Brackets (A) are not part of the overall unit

width. Unit width when mounting side frames should

be measured from outside edge of side frames.

Brackets add ≈ 1/4in [6mm] to unit's overall footprint.

Allowance is accounted for in the header installation.

2. Measure and mark:

• Measure dock door opening width (D). Divide in

half and mark the centerline of the opening at

dock level (E).

• Measure unit width and divide in half. Compare to

PAF (Product Application Form) specs.

• Measure from door centerline (E) to half of the head

frame dimension (F) and mark the outside wall (at

the bottom of the door opening or at dock level).

This mark is for the outside edge of the side frame.

• Measure (at dock level) from this mark (outside

edge of the side frame) across the door opening to

the unit width (G). Mark this measurement for the

outside edge of the second side frame.

• Consult PAF or sales representative for mounting

height to the bottom of the side pads (H). Measure

up from grade on the dock face and mark.

NOTE:Typically, the bottom of the side pad is

mounted at dock height. Some applications may

require mounting them at a di󰀨erent location.

Example: When dock bumpers are mounted

above dock height or above the pit oor (on vertical

leveler applications) it may be required to mount

the bottom of the side pads/side frames at a height

even with the top of the bumpers.

3. Dry fit and shim:

• Using carpenter’s level, plumb up the wall the height

of the side frame and mark the outside edges of the

side frames on the wall at top.

• Measure full width, etc. Using a plumb bob or

carpenter’s level make sure that the outside wall

is plumb from the highest point on the side frame

location to dock level.

• Shim side frames as required.

Figure 3

Rite‑Hite®Installation/Service/Owner's Manual Eclipse®Dock Shelter (620G, 620NH)

Publication: AMEN00141 2019-11-22 7

INSTALLATION

Side Frames Continued

Flush Mounting

Flush Mount

Bracket

O󰀨set =

‑1/4in [‑6mm] to

1/4in [6mm]

‘L’ Bracket

O󰀨set Mounting

‘L’ Bracket

Bent

‘L’ Bracket

O󰀨set =

1/2in to 3 1/2in

[13mm ‑ 89mm]

‘L’ Bracket

‘L’ Bracket O󰀨set =

4in [102mm] or

Greater

9in

[225mm] max.

Equal

9in

[225mm] max.

Equal

4. Install brackets:

NOTE:

– Side frames are supplied with brackets that

match the application (Figure 4).

– If blockouts were supplied with the unit,

reference the blockout installation manual

(Document 1321‑0008) and this manual to

ensure proper installation of the blockouts and

the side frames.

• Position the side frames on their marks.

• Mark the side frame for bracket installation (3 on

each side of each side pad) (Figure 5).

Example: Line up the mounting hole on the

bracket with a mortar joint on the wall and attach

the mounting bracket to the side frame backer

board.

• Attach the brackets to the side frame backer. Use

(supplied) 1/4in x 1 1/4in wood screws for wood

backers.

NOTICE

4in [102mm] width side frames require protective

bumpers to be installed below the side pads.

Reference "Bumpers" on page 17.

If the 4in [102mm] side frame (including blockout) has

an overall projection greater than 40in [1016mm], the

bottom, front of the blockout must be secured to either

the bumpers, the building foundation, or any other

solid rigid structure underneath the blockout. This is

required to stabilize the side frames.

5. Attach the side frames to the building wall, ensuring

they are aligned with the marks made in step 1.

NOTICE

It is critical to mount the side frames plumb and per

the building style (Mounting Methods, page 5).

Figure 4

Figure 5

Eclipse®Dock Shelter (620G, 620NH) Installation/Service/Owner's Manual Rite‑Hite®

8Publication: AMEN00141 2019-11-22

INSTALLATION

Canopy Header

NOTE:Installation procedure is the same for Standard

Pitch and Integral Hood, except that the canopy mounting

bracket is longer for the Integral Hood.

Side View

Bracket for Reference Only

Side Arm

Front Bar

1. Attach the side arms to the front bar. Before inserting

the attachment bolts, confirm orientation of the side

arms is correct (A).

2. Lift the side arm/front bar assembly together and

position across the installed side frames and

mounting brackets. Position it on top so the side arms

on the top frame are facing the wall and land between

the mounting brackets on side frames (Figure 7).

3. Connect bracket and side arm with bolt (B) on each

side of unit. Secure with (supplied) nylock nut (C).

4. Install the installation chains on both sides of the

canopy frame. The chains hold the front bar up so the

canopy cover can be attached.

• First attach quick link side (D) of the chains to the

inside legs of the canopy mounting brackets.

• Next, lift up canopy front bar and attach the "S" hook

side (E) of the chains to holes on the inside face of

the side arms.

Figure 6

Figure 7

Figure 8

Rite‑Hite®Installation/Service/Owner's Manual Eclipse®Dock Shelter (620G, 620NH)

Publication: AMEN00141 2019-11-22 9

INSTALLATION

Canopy Header Continued

Endcap Endcap

5. Unroll and then lift and lay the canopy cover (top bar

attached) on top of the side arms at the wall.

Lift up and slowly position the top bar behind the tabs

on the canopy mounting brackets.

Make sure the top bar is oriented correctly.

• All 4 faces of top bar should be covered with fabric.

• Fabric should be wrapped from front face of top bar,

under the bottom, up the back (against the wall),

across the top towards the front of the unit, then

extend from the top, front corner of the top bar down

to the front bar.

• The canopy cover and end caps (at the corners

where the canopy top and end cap meet) are laying

correctly over the edge of the mounting bracket.

6. Drape canopy cover over the front bar (the

2 1/2in [65mm] square tubing). Make sure the canopy

cover at the front corners lays correctly over the

corners of the front bar.

Side View

Part of End Cap

Removed for Clarity

Pocket with Poly

Notch

7. Wrap the canopy cover front bar pocket (with poly strip

inside), down and around the bottom of the front bar.

• The pocket/poly strip will wrap back up the back

inside face of the front bar and tuck behind the steel

angle welded at back.

• The pocket is notched to t around the side arm

bracket and the edge of the pocket should line up

with the edge of the steel angle on both ends about

1/2in [13mm] away from the side arm bracket. Make

sure that the pocket/poly strip combination gets

seated all the way down in the space between angle

and front bar.

Figure 9

Figure 10

Eclipse®Dock Shelter (620G, 620NH) Installation/Service/Owner's Manual Rite‑Hite®

10 Publication: AMEN00141 2019-11-22

INSTALLATION

Canopy Header Continued

WARNING

The canopy header is a self supporting unit.

Installing less than 6 anchors and/or insu󰀩cient

anchor installation methods is dangerous and can

cause unit failure.

Metal sided buildings require special and

increased mounting support considerations.

1 anchor location is required into solid structure

(H) (Figure 11) on each side of the door opening.

All other mounting locations require a backer

plate and pipe spacers (as needed) on the inside

of the wall so the mounting bar and the wall will

ex together.

• If structure is not aligned with 1 of the

pre-drilled mounting holes. Drill new hole

which will replace the nearest pre-drilled

mounting hole.

• If no structure is existing in this area, it must

be added at the outermost pre-drilled mounting

hole, directly above the side pad. All other

locations require a backer plate and pipe

spacers (as needed).

Endcap

Drill

Side View

8. Review "Mounting Methods" on page 5.

9. Position top bar in brackets (F). Top bar must be

secured to building in 6 locations (G).

Top bar is pre‑drilled, but other holes may be drilled

in place of these in order to line up with building

structure or to avoid obstacles.

Figure 11

Ce manuel convient aux modèles suivants

Table des matières

Manuels Abri populaires d'autres marques

Tempo Fitness

Tempo Fitness S11 Manuel utilisateur

Tuindeco

Tuindeco 42.7906 Manuel utilisateur

No Butts Bin

No Butts Bin SR1605 Manuel utilisateur

TMG

TMG TMG-DT5040CG Manuel utilisateur

TMG

TMG TMG-DT3063-PRO Manuel utilisateur

EAGLE CLAW

EAGLE CLAW Shappell DX4000 Manuel utilisateur

Kampa

Kampa Poled Shelter 300 Manuel utilisateur

Harnois

Harnois TA-R Manuel utilisateur

Shelters4Less

Shelters4Less SR1551 Manuel utilisateur

TMG

TMG TMG-DT50FW8 Manuel utilisateur

Vikre Handel AS

Vikre Handel AS JIT-1216 Manuel utilisateur

VARNA buildings

VARNA buildings C2020H Manuel utilisateur

Storage Canopy

Storage Canopy C3340R Manuel utilisateur

Frabill

Frabill ICE HUNTER 195 Manuel utilisateur

Shelters4Less

Shelters4Less SR1588 Manuel utilisateur

Sealey

Sealey Power Products GSS150819SD Manuel utilisateur

Crivit

Crivit 104155 Manuel utilisateur

No Butts Bin

No Butts Bin SR1558-F Manuel utilisateur