Rimage Amigo II Manuel utilisateur

Producer Family™ Operator

Replace the Gripper Board Assembly on a Rimage Producer System

Use this procedure to replace the gripper board assembly in an Autostar II™, Protégé II™, Amigo II™, AutoPrinter II™,

Producer 7100™, Producer 8100™, Producer 7100N™, or Producer 8100N™.

Rimage approved parts must be used for this process. The product warranty may become void if parts not approved by Rimage are

used; equipment or parts are tampered with, misused, neglected, or modified in any respect without the written consent of Rimage.

Notes:

•Your system may not look exactly like the system pictured.

•The term “Producer” is used throughout this document to refer to the Autostar II, Protégé II, Amigo II, AutoPrinter II,

Producer 7100, Producer 8100, Producer 7100N, and Producer 8100N.

Before you begin

1. Stop or pause all jobs.

2. Power off the external or embedded control

center.

3. Power off the Producer.

4. Disconnect the power cord from the power outlet.

#Required tools:

•Torx T10 screwdriver

•Torx T15 screwdriver

Remove the Gripper Board Assembly

1. Access the lift arm.

•If the system has a printer cover, remove the

printer cover.

•If the system has a top access cover, open the

top access cover.

2. Open the front door.

3. Remove the carousel.

4. If there is a flex-cable clip on the lift

arm, remove the flex-cable clip by

pulling it upward.

Note: If there is no flex-cable clip,

continue with step 5.

Printer Cover

Top Access Cover

Lift Arm

(View from Rear)

Flex-Cable Clip

Producer Family™

5. Remove the gripper assembly.

a. Disconnect flex cables A and B from the lift

arm.

-Important: If the flex cables are not

labeled as shown, use a permanent

marker to label them prior to

disconnecting the cables.

nCaution! Some cables in this system

are latched. Equipment damage may

occur if cables are not disconnected

appropriately.

b. Remove the Torx T15 screw (Qty. 1) that

secures the gripper board assembly to the

lift arm cover.

Tip: To make it easier to install the new

gripper assembly, note the position of

the screw in the gripper assembly.

c. Remove the gripper board assembly by

sliding it down and to the left.

Install the Gripper Board Assembly

1. Position the gripper board assembly inside the lift arm cover.

2. Insert and tighten the Torx T15 screw (Qty. 1) to secure the gripper board assembly to the lift arm.

3. Connect flex cables A and B to the lift arm.

4. If you removed a flex-cable clip from the lift arm, install the flex-cable clip.

Tip: Hook the flex-cable clip under the lift

arm as shown, and snap the curved part of

the clip down onto the lift arm.

Flex Cables A and B

Lift Arm

Cover

Gripper

Board

Assembly

Lift Arm

(View from Rear)

Flex Cables A and B

Flex Cable Clip

Producer Family™

5. Raise the lift arm to the top of the shaft.

6. Verify that the flag is in the center of the sensor.

Tip: Use a flashlight to clearly see the sensor

and flag.

Producer II and AutoPrinter II

Producer III and Producer IIIN

Top of System

Lift Arm

Sensor

Flag

Sensor

Side of System

Flag

Prepare the Producer for Use

1. Install the carousel.

2. Install the printer cover, or close the top access cover, as necessary.

3. Close the front door.

4. Connect the power cord to the power outlet.

5. Power on the Producer.

Run diagnostic test 3 – calibrate lift home. Refer to the Operator Level Diagnostic Tests document available

at www.rimage.com/support.html. Navigate: Producer Family > Support – Your Product > Documents tab.

Note: For AutoPrinter II, Navigate: Printer Family > Support – AutoEverest / AutoPrism, 4 Bin > Documents

tab.

Tip: If, when running diagnostic test 3, the discs are rubbing on the carousel or are not being picked

properly, align the lift arm to the carousel. Refer to the Align the Lift Arm to the Carousel document available

at www.rimage.com/support.html. Navigate: Producer Family > Support – Your Product > Documents tab.

Support information

Europe When you contact Rimage Services, please provide:

Contact Rimage Services Europe:

www.rimage.com/support.html

Email: [email protected]

Tel: +49-(0) 6074-8521-0

•Unit serial number and software version.

•Functional and technical description of the problem.

•Exact error message received.

US, Asia/Pacific, Mexico/Latin America

Contact Rimage Services:

www.rimage.com/support.html

Email: http://www.rimage.com/support_form.cfm

Tel: North America: 800-553-8312

Asia/Pacific, Mexico/ Latin America: 952-946-0004

Rimage Corporation reserves the right to make improvements to the

equipment and software described in this document at any time without

any prior notice. Rimage Corporation reserves the right to revise this

publication and to make changes from time to time in the content hereof

without obligation of Rimage Corporation to notify any person or

organization of such revisions or changes.

Autres manuels pour Amigo II

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Rimage Imprimante

Rimage

Rimage Amigo II Manuel utilisateur

Rimage

Rimage Autostar II Instructions d'utilisation et de sécurité

Rimage

Rimage Amigo II Manuel utilisateur

Rimage

Rimage Everest II Instructions d'installation

Rimage

Rimage Professional 5100N Manuel de la liste des pièces

Rimage

Rimage AutoEverest AutoPrinter Manuel utilisateur

Rimage

Rimage Prism Manuel utilisateur

Rimage

Rimage Professional 3400 Manuel utilisateur

Rimage

Rimage Everest 600 Manuel utilisateur

Rimage

Rimage Everest Guide de démarrage rapide

Rimage

Rimage AutoPrism Instructions d'utilisation et de sécurité

Rimage

Rimage Desktop 360i Instructions d'utilisation et de sécurité

Rimage

Rimage Desktop 360i Manuel utilisateur

Rimage

Rimage PrismPlus! Manuel utilisateur

Rimage

Rimage Prism Manuel utilisateur

Rimage

Rimage Prism Manuel de service

Rimage

Rimage Desktop 360i Manuel d'utilisation et d'entretien

Rimage

Rimage Amigo II Instructions d'utilisation et de sécurité

Rimage

Rimage Producer IIIN+ 8100N Manuel utilisateur

Rimage

Rimage Autostar II Manuel utilisateur

Rimage

Rimage Everest 600 Manuel utilisateur

Rimage

Rimage Autostar II Manuel utilisateur

Rimage

Rimage Desktop 360i Manuel de la liste des pièces

Rimage

Rimage 480i Instructions d'utilisation et de sécurité

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur